Lexmark Z65 Manual técnico
1
Lexmark Z65 Information Update
Cartridge packaging
Foam has been added to the packaging to give the cartridges extra protection during shipping.
Note: Remove the foam, sticker, and tape before installing your cartridges.
Printing from paper tray 1
This section replaces the information regarding the paper dimensions for printing from paper tray 1 in
the User’s Guide.
From paper tray 1, you can print on any supported paper type, such as plain, coated, photo, or glossy
paper, transparencies, envelopes, labels, iron-on transfers, or banner paper. Your paper must be within
these dimensions:
Note: Banner paper may be longer than the dimensions listed above.
Paper exit tray capacity
The paper exit tray can hold up to 150 sheets of plain paper when the printer and the paper exit tray
are both placed on one level surface.
Width: 76.2 to 215.9 mm (3.0 to 8.5 in.)
Length: 127 to 432 mm (5.0 to 17.0 in.) for Windows
127 to 355.6 mm (5.0 to 14.0 in.) for Macintosh
2
Installing additional listed printers for Windows
These steps replace the steps for installing additional listed printers for Windows in the Lexmark Z65n
Color Jetprinter User’s Guide.
After installing the first printer on your network computer, complete the following process for each
additional listed printer you want to install.
1Insert the printer software CD into the CD-ROM drive of the same network computer.
2Click Install.
3Select Install another copy of the driver software, and then click Next.
3
4From the Printer port drop-down menu, select the printer you want to install, and then click
Next.
5Follow the instructions on your screen to align the cartridges.
6From the Printer Setup is Complete screen, click Test Page to print a test page on the network
printer.
7Click Continue to complete printer software installation and for instructions about registering
your printer.
8Repeat these steps for each additional Lexmark Z65n printer you want to install on your
computer.
Replacing your printer with an identical Lexmark printer for Macintosh
Follow the steps for your operating system to replace your printer with another Lexmark Z65 printer.
Mac OS 8.6 to 9.2
1Make sure your computer is on.
2Disconnect the old printer.
3Connect the replacement printer to your computer, install the cartridges, and load plain inkjet
paper into paper tray 1. For help, refer to the setup sheet that came with your printer.
If you plug in the new printer and try to print without doing the following steps, you will get an
error message that says that there is a problem communicating with the printer. When the
message appears, click Cancel and complete the following steps to make your replacement
printer work properly.
4Select and drag the Lexmark Z65 desktop printer icon (the icon for your old printer) to the trash
can.
5From the Apple menu, choose Control Panels Lexmark Z65 Control Panel.
6From the Printer Selection screen, select your replacement printer.
4
© Copyright 2002 Lexmark International, Inc.
All rights reserved.
7Make sure Default is selected.
8Click Select.
9From the Cartridge Verification dialog box, choose whether each cartridge is old or new, and
then click OK.
If you chose old for both cartridges, Click Align Cartridges.
10 From the Alignment Screen, select Automatic Alignment and click Continue.
11 From the Alignment Status dialog box, follow the instructions on the screen.
12 After completing alignment, click the button in the upper left to close the Lexmark Z65 dialog
box.
Mac OS X version 10.0.3 to 10.1
1Make sure your computer is on.
2Disconnect the old printer.
3Connect the replacement printer to your computer, install the cartridges, and load plain inkjet
paper into paper tray 1. For help, refer to the setup sheet that came with your printer.
4From the Finder, click Applications Utilities, and then double-click Print Center to open
the Print Center.
5Select the old printer to highlight it, and then click Delete.
6Click Add Printer.
7Select your replacement printer, and then click Add.
8From the Printer menu, choose Configure Printer. The Printer Selection dialog appears.
9Double-click the name of your printer. The Lexmark Z65 Utility opens.
10 From the Cartridge Verification dialog box, choose whether each cartridge is old or new, and
then click OK.
If you chose old for both cartridges, Click Align Cartridges.
11 From the Cartridge Changed dialog, click Continue to automatically align the cartridges.
12 From the Automatic Alignment Successful dialog, click OK.
13 Click the red close button in the upper left to close the Lexmark Z65 Utility.
14 Click the red close button in the upper left to close the Print Center.
Otros manuales para Z65
3
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Impresora de Lexmark
Lexmark
Lexmark MS811 Series Manual de usuario
Lexmark
Lexmark Z730 Color Jetprinter Manual de usuario
Lexmark
Lexmark 10Z0100 Manual de usuario
Lexmark
Lexmark 4059-XXX Manual de usuario
Lexmark
Lexmark MS810 Series Manual de usuario
Lexmark
Lexmark C53x Manual de usuario
Lexmark
Lexmark T 430 Manual de usuario
Lexmark
Lexmark 7000 Color Jetprinter Manual de usuario
Lexmark
Lexmark C935 Series Manual de usuario
Lexmark
Lexmark Color Jetprinter Z55 Manual de usuario
Lexmark
Lexmark Multifunction Laser Instrucciones de instalación y mantenimiento
Lexmark
Lexmark E 450dn Manual de usuario
Lexmark
Lexmark X6100 Manual
Lexmark
Lexmark 12N0008 - C 910 Color LED Printer Instrucciones de funcionamiento
Lexmark
Lexmark X940E Manual de usuario
Lexmark
Lexmark MS315 Manual de usuario
Lexmark
Lexmark 6500E Manual
Lexmark
Lexmark 250d - E B/W Laser Printer Manual de usuario
Lexmark
Lexmark M1140 Manual de usuario
Lexmark
Lexmark C782n Manual de usuario
