Lexicon REFLEX - Manual de usuario
User Guide
DYNAMIC
REVERBERATOR
MIDI
®
Unpacking and Inspection
After unpacking the unit, save all packing materials in case you ever need to re-ship. Thoroughly inspect the unit and packing materials for signs of damage.
Report any shipment damage to the carrier at once; report equipment malfunction to your dealer.
This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause
interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in
Subpart J of Part 15 of FCC Rules, which are designated to provide reasonable protection against such interference in a residential installation. However, there is no guarantee
thatinterferencewillnotoccurinaparticularinstallation.Ifthisequipmentdoescauseinterferencetoradioortelevisionreception,whichcanbedeterminedbyturningtheequipment
OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures: reorient the receiving antenna; relocate the computer with respect
to the receiver; move the computer away from the receiver; plug the computer into a different outlet so that the computer and receiver are on different branch circuits. If necessary,
the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet prepared by the Federal
Communications Commission helpful: "How to identify and Resolve Radio/TV Interference Problems." This booklet is available from the U.S. Government Printing Office,
Washington, DC 20402, Stock No. 004-000-00345-4.
Notice
Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class B prescrites dans le Règlement sur
le brouillage radioélectrique édictépar le ministère des Communications du Canada.
Lexicon Part 070-10229 Printed in the U.S.A.
Lexicon Inc.
3 Oak Park
Bedford, MA 01730 USA
Telephone 781-280-0300
Fax 781-280-0490
Copyright 1994, Lexicon Inc.
All Rights Reserved.
Table of Contents
Getting Started .........................................................................
1
Introduction............................................................................
1
Front Panel Overview ............................................................
2
Setting Audio Levels
Rear Panel Connections........................................................
4
Footswitch Connections •Headphones
MIDI Connections •Switching from MIDI OUT to
MIDI THRU
Front Panel Operation .............................................................
7
Overview................................................................................
7
Presets and Registers ...........................................................
8
More Effects
About the Parameters..........................................................
11
Front Panel Parameter Controls
Loading an Effect.................................................................
13
Editing an Effect ..................................................................
14
Storing an Effect ..................................................................
15
Performing an Edit Compare ...............................................
16
Using Footswitches .............................................................
17
Bypass •Stepping through the Registers •Clearing
Registers •Skipping Registers and Creating Chains
Advanced Programming Mode .............................................
19
Overview..............................................................................
19
APM Utility Functions ..........................................................
20
Algorithms and Parameters .................................................
21
Hall ...............................................................................22
Plate .............................................................................23
Flanger .........................................................................24
Multi Taps.....................................................................25
Resonator.....................................................................26
Inverse..........................................................................27
Gate..............................................................................28
Chorus..........................................................................29
More about the Algorithms ...........................................30
MIDI Operation........................................................................
31
MIDI Configurations.............................................................
32
Learning a MIDI Channel.....................................................
34
Dynamic MIDI®Patching ......................................................
35
Creating a Dynamic MIDI Patch •Multiple Patches
to a Parameter •Deleting a Patch •Display of MIDI
Parameter Changes •Special Notes on MIDI
Programming •MIDI Bypass
MIDI Implementation Chart..................................................
44
Specifications.........................................................................
46
To make sure you get the most out of
Reflex, be sure to read the manual.
1
Getting Started
Introduction
Thank you for your purchase of Reflex,
Lexicon's Dynamic MIDI®Reverberator.
Reflexgivesyou8worldclassreverbera-
tion and effects algorithms to enhance any
audio performance. Sixteen preset effects
provide a wide range of superb sounds right
outofthebox,and a bank of 128registersis
available for storing your own customized
effects.—We'veloadedtheregisterswithan
additional 96 sounds to really get you going!
Reflex front panel operation is straight-
forward, with three adjustable parameters
which allow you to make subtle or dramatic
changes to each preset.
AnAdvancedProgrammingModeallows
you to access additional parameters within
each algorithm, providing fine control over
every aspect of the effects. This mode also
givesyoufrontpanelcontroloverUtilityfunc-
tions such as MIDI channel assignment and
register dumps.
Footswitch control allows you to bypass
theeffects,tostepthroughtheregisters,orto
set up register chains to suit your perfor-
mance needs
MIDI Program Change can be used to
access any register, or to bypass Reflex
processing. Beyond simple Program
Change,Reflexletsyou change parameters
in real-time, using MIDI Note Number or
continuous controllers. You can create as
many as 4 patches per effect, controlling
Predelaywith ModWheel,ReverbTimewith
MIDI Notes, etc. Dynamic MIDI™allows
exceptionally expressive performance and
sequencer control.
Two of the algorithms (Chorus and Multi
Taps)allow youtocontrolechorhythmswith
MIDI Clock, so you can synchronize delays
to drum machines and sequencers, vary the
echo repeat rate, and still maintain tempo.
Even deeper control is available through
fullMIDISysEximplementationwhichallows
bidirectional communication with a dedi-
cated controller, such as Lexicon's MRC, or
a personal computer with appropriate soft-
ware. In fact, Reflex is already compatible
withexistingeditorswhichwillrecognizeitas
a member of Lexicon's LXP series.
Front Panel Overview
2
INPUT
Sets the level of the incoming
signal.
MIX
Controls the proportion of processed
(wet) to unprocessed (dry) signals sent
to the outputs.
REGISTER/PRESET
Button selects preset or register mode.
LEDlightswhenregistermodeisselected,
turns off in preset mode.
Knob selects presets 1-16 or registers
1-128, depending on button setting.
STORE (+)/CLEAR (–)
Toggles Store and Clear functions. When "+" is
displayed, holding stores the current effect to dis-
played register. When "–" is displayed, holding
designates effect to be skipped in a footswitch step
sequence.InAdvancedProgrammingMode,clears
any patches to the displayed parameter.
INPUT
DECAY
DELAY
FX LVL
PARAMETER/LEARNSTORE (+)/CLEAR (–)
VALUE REGISTER/PRESET
9
10
11
12
13
14
15
16
8
7
6
5
4
3
2
1
RICH PLATE
DRUMPLATE
VOCAL PLATE
FLANGER
CHORUS
CANYON
MULTI TAPS
RESONATOR
GATE
INVERSE
SMALL ROOM
GUITAR STAGE
MUSIC CLUB
PIANO HALL
VOCAL HALL
LARGE HALL
DYNAMIC
REVERBERATOR
MIDI
®
OUTPUTMIX
DRY WET
VALUE
Adjusts values of selected parameter.
Displayof parametervalues isindicated
by flashing of the selected parameter
LED.
PARAMETER/LEARN
Pressing selects front panel parameters: DECAY,
DELAY or FX LVL for adjustment with the VALUE
knob.HoldingsetsReflextothe same channelasa
connecteddevice,andactivatespatchassignment.
OUTPUT
Controls Reflex's output level.
DISPLAY
Numericdisplayofdigits+1-128,anddecimalpoint.
Displayed digits indicate ID number of currently
runningeffect,orparametervalues.Decimalpointis
usedaseditindicatorandpatchindicatordepending
on mode of operation.
3
Setting Audio Levels
1. Turn Reflex INPUTand OUTPUT con-
trols all the way down (fully counter-
clockwise).
2. Connect Reflex inputs to an audio
source, and Reflex outputs to an ampli-
fier or mixer.
3. Apply an input signal at a level that you
typically use.
4. While sending audio to Reflex, gradually
turn up the INPUT control until the Input
Status LED* lights green. Continue to
advance INPUT until the LED lights red
on only the loudest peaks. If the LED is
continuously red, turn the INPUT control
down.
5. If Reflex is using a console's sends and
returns, set the MIX control fully clock-
wise (100% wet). If you are using an
instrument amplifier, start with MIX set
halfway up.
6. Gradually increase the setting of the
OUTPUT control until the audio level
from the amplifier or mixer is approxi-
mately the same as when Reflex is by-
passed.
* The Input Status LED is off when the incoming
signal is low; it lights to indicate acceptable levels
(6dB to 30dB below overload). The LED lights red
whenthesignalapproachesoverload.Acceptable
signals will trigger red flashes only on peaks.
Rear Panel Connections
4
FOOTSWITCH
Tip/Ring/Sleeve phone input, for momentary or
latching contact footswitches, allows footswitch
control of Register Step and Bypass functions.
OUPUT
Single-ended (unbalanced) stereo outputs provide
-2dBu nominal output level. Use the right output
connector for mono output. If no connection is made
attherightoutput, the leftoutputcan be usedtodrive
high-efficiency headphones at modest volume.
INPUT
Single-ended (unbalanced) inputs accept levels
as low as -30dBu. Input impedance is 50 kΩin
stereo, 25 kΩin mono. Use the right for mono
input.
POWER
Use Lexicon MSA power pack,
or 9VAC 1 amp equivalent.
MIDI
MIDI In and Out connectors are provided.
Switching an internal jumper allows selec-
tion of MIDI THRU instead of MIDI OUT.
FOOTSWITCH
POWER
OUTPUTS INPUTS
9V~, 1A,
50-60Hz
LEXICON, INC.
WALTHAM MA 02154
MADE IN U.S.A.
P/N 021-10203
SERIAL #
THIS DEVICE COMPLIES WITH PART
15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE
FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE
HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY
INTERFERENCE RECEIVED<
INCLUDING INTERFERENCE THAT
MAY CAUSE UNDESIRED OPERATION.
BYPASS
STEP
COMMON
L
(PHONES) L
R
(MONO) R
(MONO)
USE LEXICON
MSA AC ADAPTER
REFLEX
MIDI
REMOVE
RACK
EAR TO
ACCESS
MIDI
OUT/THRU
JUMPER
:TIP
:RING
:SLEEVE
OUT/
THRU IN
5
Footswitch Connections
A footswitch connected via the rear-panel
footswitchjacks allows youtoperform regis-
ter STEP and BYPASS functions. Two mo-
mentary foot-switches can be wired to a tip-
ring-sleeveconnector.AstereoY-connector
allows two identical single switches to be
used.
Headphones
A stereo signal which is adequate to drive
high-efficiency headphones is available at
the left output,
provided no connections are
madethroughtherightoutput
.Thisfeatureis
provided as a convenience for practice pur-
poses, and is intended to provide only mod-
est volume.
TIP
RING
SLEEVE
Tip Sleeve
Ring
Bypass
Step
or
TIP
RING
SLEEVE
Tip Sleeve
Ring
Bypass
Whenshipped,Reflexisconfiguredtouse
momentarycontactswitches.Youcanchange
this configuration to allow the use of latching
switches by performing the following proce-
dure:
1. SimultaneouslypressthePARAMETER/LEARN
and the REGISTER/PRESET buttons. This will
put the unit into Advanced Programming Mode
(lighting all 3 front panel parameter LEDs).
2. Turn the REGISTER/PRESET knob to 15. The
letter "F" should appear on the display.
3. Turn the VALUE knob to select 0 (latching) or 1
(momentary).
4. Press the REGISTER/PRESET button to re-
store normal front panel operation.
BYPASSSTEP
A dual-function footswitch is available from
Lexicon. A set of labels to identify footswitch
functionality is included with your unit.
6
Switching from MIDI OUT to THRU
When shipped, Reflex is configured for
MIDI OUT operation. You can easily
reconfiguretheunitforMIDITHRUoperation
with the following procedure.
1.Disconnect power.
2.Remove the two top and bottom cover
screwswhich are closestto therear panel
MIDI connectors.
3.Lay the unit upside down and remove the
rack ear.
4.Liftthejumperoffofitspinsandreposition
it according to the functionality you want.
5.Replacetherackearandthecoverscrews.
6.Reconnect power.
OUT
THRU
MIDI
REMOVE
RACK
EARTO
ACCESS
MIDI
OUT/THRU
JUMPER
OUT/
THRU
An internal jumper lets you
switch between MIDI OUT and
MIDI THRU functionality.
Front Panel Operation
Overview
Reflexfrontpaneloperationissimpleand
straightforward. Effect selection, editing,
STORE, and CLEAR functions are easily
accomplishedwithdedicatedknobsandbut-
tons.
7
This section describes all of these basic
functions, as well as using footswitches to
step through registers and register chains.
Tabla de contenidos
Otros manuales de Equipo de grabación de Lexicon
Lexicon
Lexicon 300 V 3.0 Manual de usuario
Lexicon
Lexicon 480L - UPDATE V3.0 Manual de usuario
Lexicon
Lexicon 200 Manual de usuario
Lexicon
Lexicon MC-12 V1.1 - S REV 1 Manual de instrucciones
Lexicon
Lexicon PCM 91 Manual de usuario
Lexicon
Lexicon MPX - ADDENDUM REV 1 Manual de usuario
Lexicon
Lexicon MC-12 - REV 1 Manual de usuario
Lexicon
Lexicon ALEX - REV 2 Manual de usuario
Lexicon
Lexicon I-O|22 Manual de usuario
Lexicon
Lexicon PCM 70 Manual de usuario
Lexicon
Lexicon 224X Manual de usuario
Lexicon
Lexicon PCM 81 - REV Manual de usuario
Lexicon
Lexicon PCM 90 - GUIDE REV 1 Manual de usuario
Lexicon
Lexicon LXP-15 Manual de usuario
Lexicon
Lexicon Prime Time 93 Manual de usuario
Lexicon
Lexicon PCM 81 - Manual de usuario
Lexicon
Lexicon PCM 91 Manual de usuario
Lexicon
Lexicon I-O|82 Manual de usuario
Lexicon
Lexicon PCM 80 - REV 1 Manual de usuario
Lexicon
Lexicon LDD-1 Manual de usuario
Manuales populares de Equipo de grabación de otras marcas
Strymon
Strymon NIGHTSKY Manual de usuario
Mitsubishi Electric
Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manual de usuario
Tews Technologies
Tews Technologies TPMC465 Manual de usuario
Honeywell
Honeywell Excel 50 Manual de usuario
SeaLevel
SeaLevel COMM+8.LPCI Manual de usuario
Arturia
Arturia AUDIOFUSE STUDIO Manual de usuario
