Lex 10.4 inch NEMO Manual de usuario
Assembly Guide
6G8621-2203-0100
Waterproof Panel PC
Contents
1
5
6
9
10
11
12
13
WARNING !
10.4" Waterproof Panel PC Assembly guide .............................
10.4" Waterproof Panel PC Exploded Drawing .........................
IP (International Protection)
code- Levels of Protection .......................................................
Introduction of necessary tools ...............................................
IP66 Packing list ........................................................................
IP67 Packing list ........................................................................
Difference of Waterproof cables ..............................................
I/O Connector Pinouts ..............................................................
i
WARNING !
1. Please do not remove the caps of waterproof cables unless needed.
2. Waterproof cables must be fastened tightly on the connectors of system.
3. Waterproof cables must be examined by torque wrench, and the torgue
must be more than or equal 5kgf-cm.
4. Please align the screw to the system when fasten it.
Crooked angle should be avoided.
5. Align the screws and fasten them diagonally, just loosely. Tighten them until make
sure all screws are enable to be fastened correctly to the end.
6. All top cover screws must be examined by torque wrench, and the torgue
must be more than or equal 5kgf-cm.
7. If the system error occurred, please turn the power off and unplug it from the
power supply before removing system from the water.
8. Please do not unfasten any screw unless the system is clean and completely dry.
9. Please be aware that even one drop of water might carry a risk of damage to the
waterproof connectors, make sure to avoid when removing waterproof cables.
10. To avoid causing any damage to the waterproof connectors,
using the standard tools are requested.
10.4" Waterproof Panel PC Assembly guide
1
1. Unfasten four flat-headed M3*6 screws
from the bottom cover. (Fig.1) 2. Disconnect the TOUCH CABLE
(Fig.2)
3. Unfasten four M3*4 screws from the
LCD bracket. (Fig.3) 4. Open up the LCD from left to right.
(Fig.4)
5. Install the memory module by inserting
it at 45 angles. (Fig.5) 6. Pushing the memory module down
until locked. (Fig.6)
(Fig.1)
(Fig.3)
(Fig.6)(Fig.5)
(Fig.2)
(Fig.4)
2
7. Install the CFast CARD into the slot
(Fig.7) 8. Place the HDD on the HDD KIT and
fasten four flat-headed M3*5 screws.
(Fig.8)
9. Plug in the SATA DATA CABLE to the
HDD. (Fig.9) 10. Plug in the SATA POWER CABLE
to the HDD. (Fig.10)
12. Plug in the SATA DATA CABLE to
the motherboard. (Fig.12)
11. Paste the thermal pad on the specific
area. (Fig.11)
(Fig.10)
(Fig.7)
(Fig.8)
(Fig.9)
(Fig.12)
(Fig.11)
3
13. Fasten the HDD KIT to the CASE
with four flat-headed M3*4 screws.
(Fig.14)
15. Close up the LCD to the system
(Fig.15) 16. Fasten the LCD with four flat-headed
M3*4 screws (Fig.16)
17. Connect the TOUCH CABLE (Fig.17) 18. Cover with the front panel. (Fig.18)
(Fig.13)
(Fig.14)
13. Plug in the SATA POWER CABLE to
the motherboard. (Fig.13)
(Fig.15)
(Fig.16)
(Fig.17)
(Fig.18)
4
20. Remove the waterproof caps.
(Fig.20)
21. Plug in the waterproof cables. (Fig.21)
(Fig.19) (Fig.20)
19. Turn over the whole system carefully
and fasten twelve M3*6 screws. (Fig.19)
(Fig.21)
10.4" Waterproof Panel PC Exploded Drawing
5
Dimension: 236.5(H) x 289.3(W) x 64(D) mm
8
97
11
14
12
13 10 15
1
2
3
4
5
6
1. Front Panel
2. Washer-Windows
3. Touch Panel
4. Shock-Absorbing Foam
5. Touch Bracket
6. Washer-Chassis
7. TFT-LCD Panel
8. Panel Bracket-R
9. Panel Bracket-L
10. Back Cover
11. Mainboard
12. 2.5"HDD & Kit
13. Battery Module
14. Stainless steel screws
15. Stainless steel screws -Detect
IP (International Protection) code- Levels of Protection
6
IP XX
First digit "X", Protection against solids.
Protection against the contact of external solid bodies and the access to
dangerous parts.
Image Level
0—No protection
>50 mm.
Protect against the access with
any large surface of the body,
such as the back of a hand,
but no protection against deliberate
contact with a body part.
>12.5 mm. Protect against the access with
fingers or similar objects.
>2.5 mm. Protect against the access with tools,
thick wires, etc.
>1 mm. Protect against the access with
most wires, screws, etc.
Dust protected
Ingress of dust is not entirely
prevented, but it must not enter in
sufficient quantity to interfere with the
satisfactory operation of the equipment;
complete protection against contact
Dust tight No ingress of dust;
complete protection against contact
1
2
3
4
5
6
Description of
test condition
Dimensions of the
test material
7
Second digit “X”, protection against liquids.
Protection of the equipment inside the enclosure against harmful ingress of water.
Image Level
No protection
Dripping water
Dripping water
when tilted
up to 15°
Spraying water
Splashing water
—
Dripping water
(vertically falling drops)
shall have no harmful effect.
Vertically dripping water
shall have no harmful effect
when the enclosure is tilted
at an angle up to 15° from
its normal position.
Water falling as a spray at
any angle up to 60° from
the vertical shall have no
harmful effect.
Water splashing against the
enclosure from any direction
shall have no harmful effect.
—
. Test duration: 10 minutes
. Water equivalent to
1mm rainfall per minute
. Test duration: 10 minutes
. Water equivalent to
3-5 mm rainfall per minute
. Test duration: 5 minutes
. Water volume:
0.7 Litre per minute
. Pressure: 80–100 kN/m²
. Test duration: 5 minutes
. Water volume:
10 litres per minute
. Pressure: 80–100 kN/m²
0
1
2
3
4
Description of
protection Detail of test
condition
Protected
against
Tabla de contenidos
Manuales populares de Panel táctil de otras marcas
IBASE Technology
IBASE Technology ASTUT-152-RE1S Manual de usuario
YASKAWA
YASKAWA TP 610C Manual de usuario
B&R
B&R Power Panel C Series Manual de usuario
Beijer Electronics
Beijer Electronics X2 control Manual de usuario
AXIOMTEK
AXIOMTEK GOT321W-521 Manual de usuario
TRIDONIC.ATCO
TRIDONIC.ATCO x-touchBOX Manual de usuario
