Leuze electronic IT 1900 Manual de usuario

Leuze electronic GmbH + Co. KG In der Braike 1 D-73277 Owen Tel. +49 (0) 7021 573-0

[email protected] • www.leuze.com

We reserve the right to make changes • PAL_IT1900_en.fm

zHand-held scanner for Data-Matrix Codes

and Bar Codes

zLarge reading field for the detection of high-

contrast codes

zRobust trigger button

zBuilt-in decoder

zRead-display

zRS 232, USB and PS/2 interface

zOperating temperature from 0 through 50°C

zLarger reading field through higher resolu-

tion and improved decoding

Accessories

zRS 232 cable

part no. 50115105

zTTL-RS 232 cable

part no. 50114517

zPS/2 cable

part no. 50114519

zUSB cable, 3m

part no. 50114521

zUSB helix cable, 5m

part no. 50114523

zPower supply unit

part no. 50114525

Dimensioned drawing

ACable entry:

depending on the cable, max. Ø 20mm,

cable-Ø 5mm

Electrical connection

for RS 232 cable

for USB cable

for PS/2 cable

9-pin Sub-D Signal Connection for power supply

unit IT 1900 RJ41

2TXD 4

3RXD 5

5 GND external 3

7CTS 6

8RTS 8

9 5VDC internal 7

USB type A Signal IT 1900 RJ41

15VDC7

2Data-10

3Data+9

4GND3

Mini DIN connector Mini DIN socket Signal IT 1900 RJ41

1-PCData4

22NC

33GND3

445VDC7

5-PCClock5

66NC

- 1 KB Data 8

-5KBClock6

IT 1900 2D-code hand-held scanner

IT 1900 - 01

Specifications and description

en 01-2011/04 50115720

IT 1900 - 01 2011/04

Specifications

Reading field

Electrical data

Operating voltage UB4…5.5VDC

Power consumption max. 2,3W

Interfaces

Interface type RS 232, PS/2 and USB

Trigger via button or serial command

Code types

2D codes Data Matrix ECC 200, MaxiCode, PDF417, MicroPDF, QR Code,

Aztec, Aztec Mesas, Code 49, EAN/UCC Composite

Bar codes 2/5 Interleaved, Code 39, Code 128, Code 93, Codabar, UPC/

EAN, Codablock, GS1 Databar

Optical data

Optical system high-resolution pixel array 838x640

Symbol contrast PCS 20% minimum

Light source integrated diffuse LED, wavelength 617nm ± 18nm

Read direction omnidirectional, various tilt and rotational angles

up to 45°

Mechanical data

Weight 147g (without cable)

Dimensions 104x71x160mm

Shock resistance 50 falls from a height of 1.8m

Environmental data

Ambient temp. (operation/storage) 0°C … +50°C/-40°C … +70°C

Relative air humidity 0 … 95% (non-condensing)

Protection class IP 41

0 200 400 600100 300 500 700

5 Mil

(0.127 mm)

Code 39

PDF 417

Data Matrix

QR Code

UPC 13 Mil

(0.330 mm)

20 Mil

(0.508 mm)

6,7 Mil

(0.170 mm)

10 Mil

(0.254 mm)

20 Mil

(0.508 mm)

Code 39

0 200 400 600100 300 500 700

5 Mil

(0.127 mm)

Code 39

PDF 417

Data Matrix

QR Code

UPC 13 Mil

(0.330 mm)

20 Mil

(0.508 mm)

6,7 Mil

(0.170 mm)

10 Mil

(0.254 mm)

20 Mil

(0.508 mm)

Code 39

IT 1900g HD-2 IT 1900g SR-2

Typ. read distance 1) [mm]

0 200 400 600100 300 500 700

5 Mil

(0.127 mm)

Code 39

PDF 417

Data Matrix

QR Code

UPC 13 Mil

(0.330 mm)

20 Mil

(0.508 mm)

6,7 Mil

(0.170 mm)

10 Mil

(0.254 mm)

20 Mil

(0.508 mm)

Code 39

IT 1900g ER-2

1) Dependent on code module

Typ. read distance 1) [mm]

Order guide

2D code hand-held scanner (special optics for very small codes) Part No.

IT 1900g HD-2 with RS 232, PS/2 and USB interface 50114507

2D-code hand-held scanner (standard range) Part No.

IT 1900g SR-2 with RS 232, PS/2 and USB interface 50114509

2D code hand-held scanner (special optics with large range) Part No.

IT 1900g ER-2 with RS 232, PS/2 and USB interface 50114504

Tables

Diagrams

Remarks

Ergonomically shaped hand-

held scanner with integrated

decoder for high-contrast

codes.

Data transmission via config-

urable RS 232 interface.

Or keyboard-wedge opera-

tion via PS/2 or USB inter-

face.

IT 1900

Leuze electronic GmbH + Co. KG In der Braike 1 D-73277 Owen Tel. +49 (0) 7021 573-0 IT 1900 - 01

[email protected] • www.leuze.com

Switching off the computer

Information on switching off and shutting down the connected computer - which must always be performed before connecting

peripheral devices, such as a scanner - can be found in the appropriate operating instructions for your computer.

Connecting the IT 1900

Shown in the adjacent figure is the location of the cable connection and trigger

button of the scanner. The individual steps for installing the cable on the scanner

are described below.

1.To secure the interface cable to the scanner, proceed as follows:

Insert the RJ 41 connector into the socket on the bottom of the hand-held

scanner until the connector engages.

Connect the interface cable to the appropriate connection socket on the com-

puter.

2.You may need a power supply unit for supplying voltage; alternatively, you can

use a cable which supplies voltage from the computer system. Use the pin

assignments (see "Electrical connection" on page 1) to select the appropriate

cable for your application.

3.Connect the power supply unit to the power socket (not necessary if voltage

is supplied from the computer).

4.Check the operational readiness of the scanner by pointing the scanning sur-

face towards a flat surface and pulling the trigger. A red target line as well as

the red illumination should now be visible. Now scan a sample label.

The scanner emits an audible signal to confirm that the label has been read; if

necessary, the data are now passed on to the computer.

Configuration

The hand-held scanner can always be configured using bar codes. To do this, the barcode must first be selected on the package

insert and then the trigger actuated in order to read the code. The configuration is then immediately accepted and executed.

Several of the most important configurations are listed in the following.

A second option is to configure the hand-held scanner with the USB and RS232 interfaces with the aid of the EZ Config PC

program. You can download and install this program from our homepage at www.leuze.de.

The program can be used to make settings and transfer them to the hand-held scanner. The configuration can also be stored so

that it can be reused at a later time.

Further information on this can be found in the User's Guide for the IT 1900/1902.

The standard applications are described and summarised below.

Notice!

Additional information on the device and short instructions can be found on the Internet at www.leuze.de.

Cable latch

IT 1900

IT 1900 2D-code hand-held scanner

IT 1900 - 01 2011/04

Resetting the IT 1900 to factory settings

To reset all parameters to factory settings, scan the adjacent

barcode.

Attention!

All settings are lost!!!

Trigger

To activate the read process, a trigger signal is to be sent via the serial RS 232 interface or USB interface (COM port emulation

only). The command is to be sent at the set baud rate, parity, and data and stop bits.

The command for activation is: SYN T CR ASCII decimal values: 022; 084; 013

To cancel read readiness, send a deactivation.

The command for deactivation is: SYN U CR ASCII decimal values: 022; 085; 013

Following a successful read operation, the IT 1900 deactivates itself.

The second option is activation via the built-in trigger button.

Configuration for the Leuze standard protocol

Scan the adjacent 2D code.

The IT 1900 is set to the following transmission parameters:

RS 232 transmission with 9,600 baud, 8 data bits, 1 stop bit, no parity,

prefix <STX>, terminators <CR><LF>.

IT 1900

Leuze electronic GmbH + Co. KG In der Braike 1 D-73277 Owen Tel. +49 (0) 7021 573-0 IT 1900 - 01

[email protected] • www.leuze.com

Connecting the IT 1900 to the serial PC interface

With voltage supply via PIN 9 for RS232 cable (part. no. 50114517)

required parts:

1x IT 1900g XX-2

1x 50114517 KB 232-1 IT190x

With voltage supply via power supply unit with cable RS232 (part no. 50114517)

required parts:

1x IT 1900g XX-2

1x 50114517 KB 232-1 IT190x

1x 50114525 Power supply unit

Notice!

The KB 232-1 IT190x cable (part. no. 50114517) uses TTL level (0V…5V) for data transmission. Alternatively, the

KB 232-2 IT190x cable (part. no. 50115105) can be used which works with the regular RS232 level (-12V…+12V) and

therefore features a higher interference rejection. Both cables are connection compatible.

Procedure:

1.Switch off the PC.

2.Connect the interface cable to a free COM port (RS 232) on the computer, to the IT 1900 as well as to the power supply unit (if

present).

3.Switch the PC back on.

4.Scan the adjacent barcode.

The IT 1900 is set to the following transmission parame-

ters:

RS 232 transmission with 115,200 baud, 8 data bits, 1

stop bit, no parity, terminators <CR><LF>.

5.If necessary, adjust the transmission parameters of the

used COM port to those of the IT 1900.

Attention!

We recommend connecting the IT 1900 directly to a PC or to the MA 21 or MA 41… connector units. If connecting to

other components, please note that the voltage level range is maintained on the data lines!

IT 1900 2D-code hand-held scanner

IT 1900 - 01 2011/04

Connecting the IT 1900 to the MA 41 DP-K or MA 41 IS

required parts:

1x IT 1900g XX-2

1x 50114517 KB 232-1 IT190x

1x 50114525 Power supply unit

1x 50035421 KB 021 Z

1x 50033638 MA 41 DP-K for Profibus (for Interbus: 50028994 MA 41 IS

or 50030085 MA 41 IS PDP)

Pin assignments KB 021 Z:

Core colour: signal terminal in the MA 41:

brown (RXD) 2

white (TXD) 1

blue (GND) 4

red (VCC) 

black (GND) 

bare (shield) (PE) 21

Procedure:

1.Connect cable KB 021 Z to the MA 41… acc. to the above pin assignments.

2.Connect the interface cable to cable KB 021 Z.

3.Scan the adjacent 2D code.

The IT 1900 is set to the following transmission parameters:

RS 232 transmission with 9600 baud, 8 data bits, 1 stop bit, no parity, terminators

<CR><LF>.

Connecting the IT 1900 to the MA 21

required parts:

1x IT 1900g XX-2

1x 50114517 KB 232-1 IT190x

1x 50035421 KB 021 Z

1x 50030481 MA 21 100

Pin assignments KB021 Z:

Core colour: signal terminal in the MA 21:

brown (RXD) 26

white (TXD) 27

blue (GND) 28

red (VCC) 30

black (GND) 31

bare (shield) (PE) 21

Procedure:

1.Connect cable KB 021 Z to the MA 21… acc. to the above pin assignments.

2.Connect the interface cable to cable KB 021 Z.

3.Scan the adjacent 2D code.

The IT 1900 is set to the following transmission parameters:

RS 232 transmission with 9600 baud, 7 data bits, 1 stop bit, even parity, terminators

<CR><LF>.

IT 1900

Leuze electronic GmbH + Co. KG In der Braike 1 D-73277 Owen Tel. +49 (0) 7021 573-0 IT 1900 - 01

[email protected] • www.leuze.com

Connecting the IT 1900 to the MA 2xxi

required parts:

1x IT 1900g XX-2

1x 50114517 KB 232-1 IT190x

1x 50113397 KB JST-HS-300

1x MA 2xxi for the respective fieldbus system

Procedure:

1.Connect the KB JST-HS-300 cable to the system connectors in the MA 2xxi.

2.Connect the interface cable to cable KB JST-HS-300.

3.Scan the adjacent 2D code. The IT 1900 is set to the following transmission parameters:

RS 232 transmission with 9600 baud, 8 data bits, 1 stop bit, no parity, terminators

<CR><LF>.

Connecting the IT 1900 to the PS/2 interface

The operation of the IT 1900 in keyboard emulation mode is described in this section. A PC keyboard is emulated in this operating

mode. The data which are read in are written directly to the currently activated program. Thus, the data can be processed further

in all standard programs.

required parts:

1x IT 1900g XX-2

1x 50114519 KB PS2-1 IT190x

Procedure:

1.Switch off the PC.

2.Disconnect the keyboard.

3.Plug in the IT 1900 hand-held scanner between the

keyboard and the PC.

4.Switch the PC back on.

5.Scan the 2D code shown below.

Disconnect

IT 1900 2D-code hand-held scanner

IT 1900 - 01 2011/04

Connecting the IT 1900 to the USB interface (keyboard emulation)

The operation of the IT 1900 in keyboard-emulation mode on a USB port is described in this section. A PC keyboard is emulated

in this operating mode. The data which are read in are written directly to the currently activated program. Thus, the data can be

processed further in all standard programs.

required parts:

1x IT 1900g XX-2

1x 50114521 KB USB-1 IT190x (3m, straight)

1x 50114523 KB USB-2 IT190x (5m, spiral)

Procedure:

1.Plug the IT 1900 hand-held scanner into a free USB port.

2.The scanner acknowledges this connection with a beep.

3.Scan the adjacent 2D code.

Connecting the IT 1900 to the USB interface (COM-port emulation)

The operation of the IT 1900 as a serial interface on a USB port is described in this chapter. A COM interface is emulated in this

operating mode. The data which are read in are sent to a new COM interface. The driver with which you emulate this COM inter-

face can be downloaded from our homepage at www.leuze.de. Thus, the data can be processed further in programs which expect

data via COM interfaces.

required parts:

1x IT 1900g XX-2

1x 50114521 KB USB-1 IT190x (3m, straight)

1x 50114523 KB USB-2 IT190x (5m, spiral)

Procedure:

1.Install the USB serial driver

(current version at www.leuze.com).

2.Plug the IT 1900 hand-held scanner into a free USB port.

3.The scanner acknowledges this connection with a beep.

4.Scan the adjacent 2D code.

5.Open a terminal program or your program for the serial

interface, select the new COM port, and make the

following settings: baud rate 38,400, 8 data bits, 1 stop

bit, no parity, terminator <CR>.

IT 1900

Tabla de contenidos

Otros manuales de Lector de código de barras de Leuze electronic

Leuze electronic

Leuze electronic BCL 95 Manual de usuario

Leuze electronic

Leuze electronic BCL548i Manual de usuario

Leuze electronic

Leuze electronic IT 4820 Manual de usuario

Leuze electronic

Leuze electronic CR55M2/R2 Manual de usuario

Leuze electronic

Leuze electronic BCL 22 SB Manual de lista de piezas

Leuze electronic

Leuze electronic BCL 34 Series Manual de lista de piezas

Leuze electronic

Leuze electronic BCL 600i Manual de usuario

Leuze electronic

Leuze electronic 50126970 Manual de usuario

Leuze electronic

Leuze electronic BCL 900i Series Manual de usuario

Leuze electronic

Leuze electronic BCL 248i Manual de usuario

Leuze electronic

Leuze electronic IT 1920i Manual de usuario

Leuze electronic

Leuze electronic 50130487 Manual de usuario

Leuze electronic

Leuze electronic IT 1910i Manual de lista de piezas

Leuze electronic

Leuze electronic BPS 37 Manual de lista de piezas

Leuze electronic

Leuze electronic BCL508i Manual de lista de piezas

Leuze electronic

Leuze electronic BCL 90 Manual de lista de piezas

Leuze electronic

Leuze electronic BCL 8 Series Manual de usuario

Leuze electronic

Leuze electronic VisionREADER 2300 Manual de lista de piezas

Leuze electronic

Leuze electronic BCL500i series Manual de lista de piezas

Leuze electronic

Leuze electronic DCR 55 Manual de usuario

Leuze electronic

Leuze electronic BCL558i Manual de lista de piezas

Leuze electronic

Leuze electronic IT 1911i Manual de lista de piezas

Leuze electronic

Leuze electronic BCL 8 S 2 Series Manual de usuario

Leuze electronic

Leuze electronic BCL 300 Series Manual de lista de piezas

Manuales populares de Lector de código de barras de otras marcas

POSMicro

POSMicro Datalogic PowerScan D7100 Manual de usuario

Marson

Marson MT780 Guía de configuración rápida

NCR

NCR RealPOS Manual de usuario

Motorola

Motorola SE3300 Guía de configuración rápida

Element

Element P130BT Manual de usuario

Motorola

Motorola Symbol LS3008 Manual de instalación y operación

Meec tools

Meec tools OBD-II / VAG Manual de usuario

SICK

SICK CLP 100 Manual de usuario

Royal Tag SA

Royal Tag SA I-Read Manual de usuario

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manual de usuario

Meteor

Meteor 8310 Manual de usuario

Denso

Denso BHT-500B Manual de usuario

Datalogic

Datalogic Heron HD3130 Manual de usuario

Motorola

Motorola MP6000 Instrucciones de montaje

Newland

Newland NLS-HR15-BT Manual de usuario

ARTDEV

ARTDEV AS-1310 Manual de usuario

Aopos

Aopos AS290 Manual de usuario

ENS

ENS 367-5455 Manual de usuario