Leonton RPG5-2602-2C Instrucciones de uso

⚫RPG5-2602-2C

⚫RPG5-2602-2C-T

⚫-T

This document contains information, which is protected by copyright. Reproduction, adaptation or

translation without prior permission is prohibited, except as allowed under the copyright laws.

Disclaimer

Leonton Technologies, Co. Ltd. provides this manual without warranty of any kind, expressed or

implied, including but not limited to the implied warranties of merchantability and fitness for a

particular purpose. Leonton Technologies, Co. Ltd. may make improvements and/or changes to the

product and/or specifications of the product described in this manual, without prior notice.

Leonton Technologies, Co. Ltd. will not be liable for any technical inaccuracies or typographical

errors found in this guide. Changes are periodically made to the information contained herein and

will be incorporated into later versions of the manual. The information contained is subject to

change without prior notice.

FCC Notice

This equipment has been tested and found to comply with the limits for a Class-A digital device, pursuant

to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses, and can radiate radio frequency

energy. It may cause harmful interference to radio communications if the equipment is not installed and

used in accordance with the instructions. However, there is no guarantee that interference will not occur in

a particular installation. If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

⚫Reorient or relocate the receiving antenna.

⚫Increase the separation between the equipment and receiver.

⚫Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

⚫Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications not expressly approved by the grantee of this device could void

the user's authority to operate the equipment.

Déclaration FCC

Cet équipement a été testé et reconnu conforme aux limites de la classe A pour les équipements

numériques, conformément à la section 15 des Réglementations FCC. Ces limites sont conçues pour fournir

une protection raisonnable contre toutes interférences nuisibles dans un milieu résidentiel. Cet

équipement génère, utilise, et peut émettre de l’énergie de fréquence radio et, s’il n’est pas installé et

utilisé conformément au manuel d’instruction, peut perturber la réception radio. Cependant, il n’est pas

garanti que l’équipement ne produira aucune interférence dans une installation particulière. Si cet

équipement cause des interférences nuisibles à la réception radio ou télévisée, qui peuvent être

déterminées en l’éteignant et le rallumant, l’utilisateur est encouragé à essayer de remédier au problème

en prenant les mesures suivantes:

⚫Réorienter ou déplacer l’antenne réceptrice.

⚫Augmenter la distance entre l’équipement et le récepteur.

⚫Connecter l’équipement à une prise secteur sur un circuit différent de celui utilisé par le récepteur.

⚫Consulter le négociant ou un technicien radio/TV expérimenté.

Attention: Tout changement ou modification non expressément approuvé par le concessionnaire de cet

appareil pourrait annuler l'autorité de l'utilisateur à utiliser l'équipement.

CE Mark Warning

This is a Class-A product. In a domestic environment this product may cause radio interference in which

case the user may be required to take adequate measures.

CE Mark Avertissement

Ceci est un produit de classe A. Dans un environnement domestique, ce produit peut être utilisé en

présence d'interférences radio.

This document is the current official release manual. Please check our website (www.leonton.com) for

any updated manual or contact us by e-mail (sales@leonton.com).

 
 
CONTENT 
OVERVIEW ................................................................................................................................... 1 
Key Features.................................................................................................................................................................1 
Package Contents.......................................................................................................................................................2 
Safety Precaution........................................................................................................................................................2 
HARDWARE DESCRIPTION...................................................................................................... 3 
Physical Dimensions ..................................................................................................................................................3 
Front Panel....................................................................................................................................................................4 
LED Indicators..............................................................................................................................................................5 
Ethernet Ports..............................................................................................................................................................6 
Cabling...........................................................................................................................................................................7 
Wiring the Power Inputs...........................................................................................................................................9 
Wiring the Fault Alarm Contact ..............................................................................................................................9 
Grounding Note........................................................................................................................................................10 
MOUNTING INSTALLATION..................................................................................................11 
Rack Mounting ..........................................................................................................................................................11 
HARDWARE INSTALLATION..................................................................................................12 
Installation Steps ......................................................................................................................................................12 
TROUBLE SHOOTING ..............................................................................................................14 

OVERVIEW

This series is rated IP40 and Rack-Mounting installation. Each unit of this industrial gigabit managed

Ethernet switch series has 24*10/100/1000Tx with IEEE 802.3at compliant ports (30W/port) and 2 Gigabit

combo ports (2*10/100/1000Tx RJ45 or 2*100/1000 SFP slots), suitable for applications that require high

bandwidth and long-distance communication.

In order to prevent unregulated voltage, this series provides high EFT and ESD protection. This also allows

it to function in harsh environments, as well as support power redundancy with a dual power input design

with reverse polarity protection. The built-in relay warning function alerts users about occurring power

failures.

With one model having an operating temperature of -10 to 65°C and another with a wide operating

temperature of -40 to 75°C, this series is designed to meet any needs in industrial automation, outdoor

application and harsh environments.

Key Features

Interface & Performance

⚫All copper ports support auto MDI/MDI-X function

⚫Embedded 24*10/100/1000Tx (PSE 30W/Port) and 2*gigabit combo ports (2*10/100/1000Tx copper

ports or 2*100/1000 SFP Slots)

⚫Store-and-forward switching architecture

⚫8K MAC Address Table

⚫Supports 9.6Kbytes Jumbo Frame

⚫4Mbits memory buffer

Power Input

⚫Dual 48-55VDC redundant power inputs with connective 8-pin terminal block

⚫Max. current 15.5A

⚫Max. PoE output: 720W

⚫Relay Contact: 24 VDC, 1A resistive

⚫The power input specification is complied with the requirements of SELV (Safety Extra Low Voltage),

and the power supply should be complied with UL 61010-1 & UL 61010-2-201

Certification

⚫CE/FCC

⚫UL 61010-1

⚫UL 61010-2-201

Operating Temperature

⚫Standard operating temperature model: -10°C ~ 65°C

⚫Extended operating temperature model (–T): -40°C ~ 75°C

Case/Installation

⚫IP40 protection

⚫Rack-mount design

⚫Installation in a pollution degree 2 industrial environment

⚫Standalone Installation

Package Contents

⚫1 –RPG5-2602-2C(-T) - Unit weight: 2.82kg (6.22 lb), Shipping weight: 3.54kg (7.80 lb)

⚫2 –Rack-mounting brackets and screws

⚫1 –Quick installation guide

⚫1 –RJ45 to DB9 Serial Console cable

Safety Precaution

Attention

If the DC voltage is supplied by an external circuit, please use a protection device on the power supply input.

Supply by UL Listed industrial use power. The industrial Ethernet switch’s hardware specs, ports, cabling

information, and wiring installation will be described within this user manual.

Attention

Si la tension CC est fournie par un circuit externe, veuillez utiliser un dispositif de protection sur l'entrée

d'alimentation. Fourniture par courant industriel homologué UL. Les spécifications matérielles, les ports, les

informations de câblage et l'installation du câblage du convertisseur de média industriel seront décrits dans

ce manuel d'utilisation.

Warning Labels

The caution label means that you should check the certain information on user manual when working with

the device. (Shown in Figure 1.1)

Étiquettes d'avertissement

L'étiquette d'avertissement signifie que vous devez vérifier certaines informations sur le manuel d'utilisation

lorsque vous travaillez avec l'appareil. (Montré dans la Figure 1.2)

Figure 1.1 - Caution Label

Figure 1.1 - Étiquette de mise en garde

Figure 1.2 - Hot Surface Warning Label

Figure 1.2 - Étiquette d'avertissement de surface chaude

HARDWARE DESCRIPTION

Physical Dimensions

Figure 2.1, below, shows the physical dimensions of RPG5-2602-2C series.

(W x H x D) is 440mm x 44mm x 200mm

Figure 2.1: Physical Dimensions

Front Panel

The front panel of the RPG5-2602-2C series industrial gigabit managed ethernet switch is shown below in

Figure 2.2.

Figure 2.2: The Front Panel of RPG5-2602-2C Series

Rear Panel

Figure 2.3, below, shows the rear panel of the RPG5-2602-2C series switch that is equipped with one 8-pin

redundant power inputs (48-55VDC) and one 2-pin terminal block for relay output.

Figure 2.3: The Rear Panel of RPG5-2602-2C Series

PoE Status LED indicator (Port 1-24)

LEDs for Power1, Power2, Fault,

Master, Ring

Reset Button

RS-232 Serial Console

USB 2.0 for Configuration Backup/Restore

10/100/1000Tx RJ45 PoE+

Copper Port (Port 1-24)

10/100/1000Mbps Copper Link/Act

LED indicator (Port 1-24)

100/1000Mbps SFP Link/Act

LED indicator (Port 25-26)

(Combo Port 25-26)

10/100/1000Tx RJ45 Copper

Port & 100/1000 SFP Port

1Gbps Copper Link/Act LED indicator

10/100Mbps Copper Link/Act

LED indicator

Power Input 2

Connector

Power Input 1

Connector

24VDC@1A Relay Output

Grounding Screw

LED Indicators

There are LED light indicators located on the front panel of the industrial switch that display the power status

and network status. Each LED indicator has a different color and has its own specific meaning, see below in

Table 2.1.

LED

Color

Description

Green

Power input 1 is active

Off

Power input 1 is inactive

Green

Power input 2 is active

Off

Power input 2 is inactive

FAULT

Green

No event happened

Red

1. System booting

2. Configured event happens

Flashing

Firmware upgrading

MASTER

Green

ERPS Owner Mode (Ring Master) is ready

Off

ERPS Owner Mode is not active

RING

Green

ERPS Ring Network is active and works well

Flashing

ERPS Ring works abnormally or misconfigure

Off

ERPS Ring Network is not active

(LAN Port 1-24)

Green

Connected to network, 10/100/1000Mbps

Flashing

Networking is active

Off

Not connected to network

PoE

(LAN Port 1-24)

Green

Supplying power to the powered-device

Off

Not connected to a Powered Device

Combo Port

(LAN Port 25-26)

Connected to network, 1000Mbps

Flashing

Networking is active

Off

Not connected to network

Combo Port

10/100

(LAN Port 25-26)

Connected to network, 10/100Mbps

Flashing

Networking is active

Off

Not connected to network

Combo Port

L/A

(SFP Port 25-26)

Green

Connected to network, 1000Mbps

Flashing

Networking is active

Off

Not connected to network

Amber

Connected to network, 100Mbps

Flashing

Networking is active

Off

Not connected to network

Table 2.1: LED Indicators

Ethernet Ports

RJ-45 Ports (Auto MDI/MDIX)

The RJ-45 ports are auto-sensing for 10Base-T, 100Base-TX or 1000Base-T devices

connections. Auto MDI/MDIX means that the switch can connect to another switch

or workstation without changing the straight-through or crossover cabling. See the

figures as below for straight-through and crossover cabling schematics.

10/100BASE-T(X) RJ-45 Pin Assignments (Table 2.2)

Crossover Cable

Straight Through Cable

Pin Number / Signal

1 / RX+

3 / TX+

1 / RX+

1 / TX+

2 / RX-

6 / TX-

2 / RX-

2 / TX-

3 / TX+

1 / RX+

3 / TX+

3 / RX+

6 / TX-

2 / RX-

6 / TX-

6 / RX-

Table 2.2

1000BASE-T RJ-45 Pin Assignments (Table 2.3)

Crossover Cable

Straight Through Cable

Pin Number / Signal

1 / TP0+

3 / TP1+

1 / TP0+

1 / TP1+

2 / TP0-

6 / TP1-

2 / TP0-

2 / TP1-

3 / TP1+

1 / TP0+

3 / TP1+

3 / TP0+

4 / TP2+

7 / TP3+

4 / TP2+

4 / TP3+

5 / TP2-

8 / TP3-

5 / TP2-

5 / TP3-

6 / TP1-

2 / TP0-

6 / TP1-

6 / TP0-

7 / TP3+

4 / TP2+

7 / TP3+

7 / TP2+

8 / TP3-

5 / TP2-

8 / TP3-

8 / TP2-

Table 2.3

Note: “+” and “-” signs represent the polarity of the wires that make up each wire pair.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Hardware de red de Leonton

Leonton

Leonton CBG5-0602-SFP-Lite Instrucciones de uso

Leonton

Leonton REG2-2602-2C Instrucciones de uso

Leonton

Leonton GINJ-0201-EBT Instrucciones de uso

Leonton

Leonton CBG2-0501-SFP Instrucciones de uso

Leonton

Leonton CEG5-0602-SFP Instrucciones de uso

Leonton

Leonton GINJ-0201-AT-24 Series Manual de usuario

Leonton

Leonton CEG5-0602-SFP-Lite Series Instrucciones de uso

Leonton

Leonton REG5-2602-2C Series Instrucciones de uso

Leonton

Leonton CBG2-0501-SFP-12 Instrucciones de uso

Leonton

Leonton GINJ-0201-BT-12-T Instrucciones de uso

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario