Lenz digital plus lh01 Manual de usuario
1
B.B.10.0021
Information LH01
Art. no. 21010
2nd version 0515
2 Information LH01
Table of contents
1Welcome! ........................................................................................ 4
2Important advice, please read first! ................................................ 5
3Overview of the features of the LH01 ............................................. 6
4Operating elements of the LH01..................................................... 9
5Connection and initial operation ................................................... 10
6Emergency shutdown ................................................................... 12
7Controlling locomotives................................................................. 13
7.1 Changing the speed step....................................................... 13
7.2 Changing the direction of travel / Emergency stop................ 14
8Selecting locomotives ................................................................... 15
8.1 Selecting a locomotive address from the stack ..................... 15
8.2 Entering a new locomotive address into the stack ................ 16
8.3 Deleting a locomotive address from the stack....................... 18
9Locomotive functions .................................................................... 19
9.1 Switching locomotive functions with function keys ................ 19
9.2 Switching locomotive functions with the rotary knob ............. 20
9.3 Assigning locomotive functions to function keys ................... 21
9.4 Setting a locomotive function to permanent or temporary
operation ................................................................................ 22
9.5 Assigning function acronyms to locomotive functions ........... 24
9.6 Deleting a function acronym .................................................. 26
9.7 Changing a function acronym................................................ 27
9.8 Deleting all function acronyms............................................... 28
10 Double traction (Double Header).................................................. 29
10.1 Requirements to assemble a double traction ........................ 29
10.2 Assembling two locomotives in a double traction.................. 29
10.3 Deleting a double traction...................................................... 31
10.4 Error messages during double tractions................................ 32
11 Switching points and signals......................................................... 33
12 Setting (programming) locomotive decoders (PoM)..................... 34
12.1 Reading CVs via PoM and the address display LRC120...... 36
13 System settings............................................................................. 38
3
13.1 Setting and reading a locomotive address on the
programming track................................................................. 40
13.2 Setting and reading the XpressNet address.......................... 44
13.3 Setting the language.............................................................. 46
13.4 Resetting the LH01 ................................................................ 47
13.5 Resetting command stations (LZV100/LZ100)...................... 48
13.6 Displaying the version number of the LH01 .......................... 49
13.7 Displaying the version number of the command station........ 50
13.8 Setting the club mode ............................................................ 51
13.9 Displaying the hardware ID ................................................... 54
13.10Setting the brightness of the display...................................... 55
13.11Enabling/Disabling the displaying of function acronyms ....... 56
14 Technical appendix....................................................................... 57
14.1 Help in case of malfunction.................................................... 57
14.2 List of error messages ........................................................... 58
14.3 Display text / Languages ....................................................... 59
4 Information LH01
1 Welcome!
We would like to congratulate you on your acquisition of the LH01 by
Digital plus by Lenz®. We hope you will enjoy this model railway
control.
The purpose of this operating manual is to explain the use of the
LH01. If you still have questions after reading this manual, please
contact us. We will be happy to help you. There are four different
ways of contacting Lenz Elektronik GmbH:
Mail address:
Lenz Elektronik GmbH
Vogelsang 14
D-35398 Giessen
Phone:
+49 (0) 6403 900 133
A recorded message will
inform you of our
availability.
Fax:
+49 (0) 6403 900 155
E-mail:
If you encounter any problems with the LH01, please contact us,
providing a problem description as well as the following information:
Version number of the command station
Version number of the LH01
Designation, version number and service number of all connected
XpressNet devices (additional manual controls, Interface etc.).
This will help our service department solve the problem. Thank you.
1.1.1 All present?
Please check if all components have been delivered:
- LH01 device
- Connecting cable
- Operating manual (this booklet)
If any component is missing, please ask your specialist supplier for a
subsequent delivery.
5
2 Important advice, please read first!
The manual control LH01 is a component of the
Digital plus by Lenz
®
system and was submitted to intensive testing before delivery. Lenz
Elektronik GmbH guarantees fault-free operation if you follow the
advice below:
The LH01 may only be operated with
Digital plus by Lenz
®
system
components. Any use other than that described in this operating
manual is not permitted and all guarantees will be invalid if the LH01
is used inappropriately. Connect your LH01 only to devices that are
designated for such connection. This operating manual will tell you
which devices are suitable. Do not expose the LH01 to damp or direct
sunlight.
WARNING!
Do not leave your model railway system unsupervised
during operation! The heat generated by a short-
circuit creates a fire risk!
6 Information LH01
3 Overview of the features of the LH01
Locomotive
addresses
Locomotive addresses range from 1 - 9999.
Address 0 is used to control an analogue
locomotive.
Stack for
locomotive
addresses
The LH01 has a stack for locomotive addresses
that comprises 12 slots. The stack serves to
store the locomotive addresses as well as the
settings used most frequently.
Locomotive
functions and
configuration
Up to 29 functions are available for each
locomotive address.
Use of the LH01 with a command station LZV100
facilitates the independent setting of these 29
functions to permanent or temporary operation.
This setting is stored with the locomotive address
in the LZV100.
Permanent operation:
Press the key once to
enable this function and
again to disable this
function.
Temporary operation:
This function is enabled
as long as the
corresponding key is
pressed, and disabled
as soon as the key is
released.
Function
acronyms
You can assign an acronym to each of the 29
functions from among the list of acronyms
contained in the LH01. This facilitates finding a
desired function. You can enable and disable the
display of acronyms.
Speed steps
The LH01 supports 28 or 128 speed steps
depending on the mode set in the command
station for the respective locomotive address.
The mode cannot be changed.
Club mode
The LH01 has two so-called ‘club modes’in
which certain functions of the LH01 are disabled.
This allows operation by model railway fans who
are not fully familiar with the LH01.
Double traction
Two locomotives can be joined in a double
traction and controlled simultaneously.
7
Multiple traction
Multiple tractions that are already joined (by
means of the LH100 or LH90) can be controlled.
It is not possible to join a multiple traction with the
LH01.
Programming in
operational
mode (PoM)
PoM allows you to change the settings of the
locomotive that is currently being controlled. You
can change, for example, the starting delay,
maximum speed, or sound volume.
Changing a
locomotive
address
You can read or change a locomotive address on
the programming track of the LZV100.
Points, signals
and other
accessories
The address range for points, signals and other
accessories (for example, uncouplers) ranges
from 1 to 999.
XpressNet
Communication with the command station is
made through the XpressNet connection.
As is the case with all other XpressNet devices,
your LH01 can be disconnected and reconnected
during operation. The locomotive controlled last
will continue its operation with the last settings
stored. Once reconnected, this locomotive will
again be controlled.
Housing
Plastic
Dimensions
W 70 mm x H 125 mm x D 38 mm
8 Information LH01
Illustrations in the step-by-step instructions:
Key
Display
Explanation
In this booklet all entries in the LH01 are shown on the left.
All corresponding illustrations of the display after entry are
shown on the right.
All operating steps described in this booklet presume that the
LH01 is connected to the Digital plus by Lenz ®system and
that the system is turned on.
Illustration of displays and operating elements:
‘0001’'Esc'
The displays and operating elements of the LH01 are depicted
as illustrations. References to the display are indicated by
single quotes (‘’).
Cross references:
(p. 23)
This arrow refers to specific pages of the operating manual
that contain further information on a given subject.
Important information:
Text boxes contain important information or
advice.
9
4 Operating elements of the LH01
The rotary knob is
used to make
entries. Apart from
the rotary function,
the knob has five
key functions: up,
down, left, right,
and centre.
Function keys
A, B, and C:
For each locomotive
address in the stack,
locomotive functions
(F0 to F28) can be
assigned to these
keys.
Use the ‘Esc’ key to
go back one step in
the menu structure.
The LEDs
surrounding the
rotary knob indicate
when you are in one
of the menus.
10 Information LH01
5 Connection and initial operation
The LH01 can be used with the command stations LZ100 or LZV100.
The LH01 requires the software version 3.6 for the
command station LZ100/LZV100.
Update your command station, if necessary.
1.
Insert the Western plug of the enclosed connecting cable
into the socket of the LH01.
2.
Insert the five-pole DIN plug into the five-pole DIN socket
at the back of the LZ100/LZV100.
Otros manuales para digital plus lh01
1
Tabla de contenidos
Otros manuales de Mando a distancia de Lenz
