Lenovo ThinkSystem RAID 940-16i 8GB Flash PCIe Gen4... Manual de usuario

ThinkSystem RAID 940-16i 8GB Flash PCIe

Gen4 12Gb Internal Adapter Installation and

User Guide

First Edition (April 2020)

LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant to a General Services

Administration (GSA) contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-

05925

Table of Contents

Chapter 1: Overview ...........................................................................................................................4

1.1 RAID Features...................................................................................................................................................... 4

1.2 Operating System Support................................................................................................................................. 5

1.3 PCIe Host Interface ............................................................................................................................................. 5

1.4 LED Management ................................................................................................................................................ 6

1.5 Tri-Mode Storage Interface Features................................................................................................................. 6

1.6 Adapter Characteristics...................................................................................................................................... 6

Chapter 2: Hardware Installation Instructions..................................................................................8

Chapter 3: Safety Characteristics ...................................................................................................10

and User Guide

Chapter 1: Overview

The Thinksystem RAID 940-16i 8GB Flash PCIe Gen4 12Gb Internal Adapter, based on the SAS3916 tri-mode controller,

is a high-performance PCIe-to-SATA/SAS/PCIe (tri-mode) storage adapter. The tri-mode SerDes technology enables

operation of SAS, SATA, or PCIe (NVMe) storage devices in a single drive bay. A single controller can operate in all three

modes concurrently: SAS, SATA, and PCIe/NVMe. The adapter negotiates between the speeds and the protocols to

recognize and concurrently interface with these three storage devices types.

The adapter provides the following storage interface data transfer rates:

SAS data transfer rates of 12Gb/s, 6Gb/s, and 3Gb/s per phy

SATA transfer rates at 6Gb/s and 3Gb/s per phy

PCIe (NVMe) data transfer rates of 16 GT/s, 8 GT/s, 5 GT/s, and 2.5 GT/s per lane

The following table summarizes key adapter features.

Table 1 Adapter Features

Adapt

40-16i

Ports

16 internal

I/O Processor

SAS3916

Form Factor

Custom

Storage Interface Connectors

Four SFF-8654 x4

Host Interface

SFF-8654 x8

Storage Interface

SAS, SATA, and PCIe (NVMe)

Cache Memory

8 GB, 2666 MT/s, DDR4 SDRAM

Cache Protection

Yes

Super Capacitor

CVPM05 module

1.1 RAID Features

The following list includes primary RAID features that the adapter supports.

RAID levels 0, 1, 5, and 6

RAID spans 10, 50, and 60

JBOD mode with RAID0, RAID1, and RAID10

JBOD for SDS environments

Online Capacity Expansion (OCE)

Auto resume after loss of system power during array rebuild or OCE

Single controller multipathing

Load balancing

Configurable stripe size up to 1 MB

Fast initialization for quick array setup

Check Consistency for background data integrity

SSD support with SSD Guard™ technology

Patrol read for media scanning and repairing

Disk data format (DDF)-compliant Configuration on Disk (COD)

Self-Monitoring, Analysis, and Reporting Technology (S.M.A.R.T) support

and User Guide

Global and dedicated hot spare with revertible hot spare support

Automatic rebuild

Enclosure affinity

Emergency SATA hot spare for SAS arrays

Enclosure management

SCSI Enclosure Services (SES) (inband)

SGPIO (sideband) or I2C (UBM) enclosure management

DataBolt bandwidth optimizer technology support for compatible expander-based enclosures

Shield state drive diagnostic technology

1.2 Operating System Support

The adapter supports the operating systems in the following list.

Microsoft Windows

VMware vSphere/ESXi

Red Hat Enterprise Linux

SuSE Linux

Ubuntu Linux

Citrix XenServer

CentOS Linux

Debian Linux

Oracle Enterprise Linux

Fedora

FreeBSD

Visit http://support.lenovo.com, and download the latest firmware and driver for the adapter.

1.3 PCIe Host Interface

The adapter’s PCIe 4.0 host interface provides maximum transmission and reception rates of up to 128 GT/s (16 Gb/s per

lane). The tri-mode controller uses a packet-based communication protocol to communicate over the serial interconnect.

Other PCIe host interface features include the following:

Eight-lane PCIe host interface

PCIe Hot Plug

Power management

– Supports the PCI Bus Power Management Interface Specification Revision 1.2

– Supports Active State Power Management, including the L0 states, by placing links in a power-saving mode

during times of no link activity

Error handling

High bandwidth per pin with low overhead and low latency

Lane reversal and polarity inversion

Single-phy (one-lane) link transfer rate of 16 GT/s, 8 GT/s, 5 GT/s, and 2.5 GT/s in each direction

Eight-lane aggregate bandwidth of up to 16 GB/s (16,000 MB/s)

Support of x8, x4, x2, and x1 link widths

and User Guide

1.4 LED Management

The adapter offers LED management support for SAS/SATA backplanes and (PCIe) NVMe backplanes. External connect

adapters offer enclosure LED management support for enclosure implementations through SES.

1.5 Tri-Mode Storage Interface Features

The adapter’s storage interface supports concurrent operation with SAS, SATA, and PCIe (NVMe) devices to provide a

fully functional solution for any storage environment.

PCIe (NVMe) interface features:

– Up to sixteen x1, eight x2, or four x4 NVMe direct-attach drive support

– Data transfer at 16 GT/s, 8 GT/s, 5 GT/s, and 2.5 GT/s

– Independent resets and configuration

– Common reference clock and separate reference clock independent SSC (SRIS) support

SAS features:

– SAS data transfers at 12Gb/s, 6Gb/s, and 3Gb/s

– DataBolt technology on all SAS phys to improve performance

– Serial, point-to-point, enterprise-level storage interface

– Wide ports that contain multiple phys

– Narrow ports that contain a single phy

– SAS phy power management

– Data transfer by using SCSI information units

– T10 data protection management

– Support for persistent connection capability

– Support for SPL-3 initiate close capability

– Configurable Rx and Tx polarity inversion

– Configurable phy-to-disk mapping

– Configurable SSC

SATA interface features:

– SATA and STP data transfers at 6Gb/s and 3Gb/s

– Addressing of multiple SATA targets through an expander

1.6 Adapter Characteristics

The adapter is a 6.02 in. × 2.67 in. (153 mm × 67.7 mm) board. The following figure shows the connectors and LED

locations on the adapter.

and User Guide

Figure 1 Card Layout for the Thinksystem RAID 940-16i 8GB Flash PCIe Adapter

The following table describes the headers and connectors on the adapter.

Table 2 Headers and Connectors

Con

nector

ription

andard edge card connector

he interface between the storage adapter and the host system.

Default serial boot ROM (SBR) header

2-pin connector. Reserved.

n-board serial UART connector

-pin connector. Reserved.

(C3), J6 (C2),

7 (C1), J18 (C0)

orage interface connectors

Four

SFF-8654 4-port internal connectors.

Connect the adapter by cable to the storage devices.

J14

Supercap i

nterface connector

-pin connector.

nnects the adapter to a supercap module.

J25

Power

Power connector.

The following table describes the LEDs on the adapter.

Table 3 LED Designations

LED

ription

LED 2

ellow controller over temperature

Stays

on solid to indicate that the SAS3916 device temperature sensor is over the

temperature threshold. When the device is in the proper temperature range, this LED is off.

LED 3

Green system heartbeat

Indicates that the SAS3916 RoC ASIC is operating normally. This LED blinks at 1 Hz.

LED 5

ellow supercap fault

Ind

icates that the supercap pack is in fault state or is over temperature. This

LED res

ides on the nonheat-sink side of the board.

ED 6

reen Open NAND Flash Interface

(

ONFI) activity

Ind

icates when the ONFI is active for cache offload or recovery.

and User Guide

Chapter 2: Hardware Installation Instructions

To install the adapter, follow these steps:

1. Unpack the adapter and inspect the adapter for damage.

Unpack the adapter in a static-free environment. Remove the adapter from the antistatic bag, and carefully inspect the

adapter for damage. If you notice any damage, contact Lenovo or your reseller support representative.

ATTENTION To avoid the risk of data loss, back up your data before you change your system configuration.

2. Review the adapter connectors.

3. Check whether the adapter is well-fixed on the mounting bracket.

The adapter ships preinstalled on a mounting bracket. Check that the adapter is fixed in place. If any loose screws

exist, tighten the screws using a No.1 Phillips torque screwdriver. The maximum torque is 4.8 ± 0.5 inch-pounds.

ATTENTION Exceeding this torque specification can damage the board, connectors, or screws, and can void

the warranty on the adapter. Damage caused to the adapter as a result of changing the bracket

can void the warranty on the board. Adapters returned without a bracket mounted on the board

will be returned without return merchandise authorization (RMA) processing.

4. Prepare the server.

Turn off the power to the server and disconnect all power cords.

5. Remove the top cover from the chassis.

6. Remove any components that might impede the adapter installation.

Refer to ThinkSystem Server Documentation Center, select your product, and review the Hardware replacement

procedures section for detailed instructions.

7. Install the adapter.

Align the notches on the mounting bracket with the four pins or three pins on the chassis, place down the adapter, and

slightly slide the adapter to secure it in place, as the following figure shows.

ATTENTION The shape, size, and locations of the components on your adapter and its bracket might vary

from the following illustration.

Figure 2 Installing the Adapter

8. Connect any cables to the adapter.

Refer to ThinkSystem Server Documentation Center, select your product, and review the Internal cable routing

section for detailed instructions.

and User Guide

9. Reinstall any parts that have been previously removed and connect any internal cables.

Refer to ThinkSystem Server Documentation Center, select your product, and review the Hardware replacement

procedures section and the Internal cable routing section for detailed instructions.

10. Reinstall the top cover on the chassis.

Refer to ThinkSystem Server Documentation Center, select your product, and review the Hardware replacement

procedures for detailed instructions.

11. Reconnect any external cables and turn on the power to the system.

The hardware installation of your adapter is complete.

and User Guide

Chapter 3: Safety Characteristics

The adapter meets or exceeds the requirements of UL flammability rating 94 V0. Each bare board is also marked with the

supplier name or trademark, type, and UL flammability rating. For the boards installed in a PCIe bus slot, all voltages are

lower than the SELV 42.4 V limit.

Tabla de contenidos

Otros manuales de Adaptador de Lenovo

Lenovo

Lenovo WD100 Manual de usuario

Lenovo

Lenovo 45K5296 Manual de usuario

Lenovo

Lenovo CH580 Manual de usuario

Lenovo

Lenovo 200 Series Manual de usuario

Lenovo

Lenovo NETWORK CARD - WIRELESS ADAPTER MW600-B-LO Manual de usuario

Lenovo

Lenovo 4X90K86568 Manual de usuario

Lenovo

Lenovo ThinkPad 90W Slim AC/DCCombo Adapter Manual de usuario

Lenovo

Lenovo ThinkPad EM7345 Manual de usuario

Lenovo

Lenovo ThinkPad N5321 Manual de usuario

Lenovo

Lenovo Intel X520 Manual de usuario

Lenovo

Lenovo 43N3412 Manual de usuario

Lenovo

Lenovo IdeaPad 65W AC Adapter Manual de usuario

Lenovo

Lenovo 90W AC/DC Manual de usuario

Lenovo

Lenovo Brocade 16Gb FC Single-port Manual de usuario

Lenovo

Lenovo ThinkSystem 1610-4P Manual de usuario

Lenovo

Lenovo ThinkSystem RAID 940-16i Manual de usuario

Lenovo

Lenovo ThinkSystem 440-16i Manual de usuario

Lenovo

Lenovo EN2024 Manual de usuario

Lenovo

Lenovo Emulex 16 Gb Gen 6 Manual de usuario

Lenovo

Lenovo USB 3.0 to DVI/VGA Monitor Adapter Manual de usuario

Lenovo

Lenovo Flex System IB6132 Manual de usuario

Lenovo

Lenovo Y Series Manual de usuario

Lenovo

Lenovo ThinkSystem 4350 Series Manual de usuario

Lenovo

Lenovo ThinkPad 72W Manual de usuario

Manuales populares de Adaptador de otras marcas

PCB Piezotronics

PCB Piezotronics 090B274 Manual de usuario

Auvidea

Auvidea J20 Manual del producto

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manual de usuario

Akribis

Akribis ITF-21-BISS-MIT Manual de usuario

Tenda

Tenda W54U Manual de usuario

ROHO

ROHO AGILITY Manual de usuario

PROLiNK

PROLiNK WN2001 Manual de usuario

Hawking

Hawking HUF2 Manual de usuario

Airlink101

Airlink101 AWLC4030 Manual de usuario

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manual de usuario

Philips

Philips SWA4554S/10 Manual de usuario

JVC

JVC TS-C9D2B Manual de instrucciones

NETGEAR

NETGEAR A6100 Manual de usuario

D-Link

D-Link DWA-121 Manual de usuario

Philips

Philips SWA2037 Manual de usuario

Basalte

Basalte 0610-20 Manual de usuario

Yealink

Yealink EHS40 Manual de usuario

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manual de usuario