Lennox Elite series Manual de usuario

Report No. 116-F-15-5

CARE AND OPERATION INSTRUCTIONS

B-Vent Gas

Fireplace Heater Inserts

Do not store or use gasoline or other ﬂammable

vapors or liquids in the vicinity of this or any other

appliance.

WHAT TO DO IF YOU SMELL GAS:

• Do not light any appliance.

• Do not touch any electrical switch; do not

Use any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow your gas supplier's

instructions.

• If your gas supplier cannot be reached, call

the ﬁre department.

Installationandservicemustbeperformedbyaquali-

ﬁed installer, service agency or the gas supplier.

POUR VOTRE SÉCURITÉ: Ne pas entreposer ni utiliser

d’essence ni d’autre vapeurs ou liquides inﬂammables dans

le voisinage de cet appareil ou de tout autre appareil.

POUR VOTRE SÉCURITÉ: Que faire si vous sentez une odeur

de gaz:

• Ne pas tenter d’allumer d’appareil.

• Ne touchez à aucun interrupteur. Ne pas vous servir

des téléphones se trouvant dans le batiment où vous

vous trouvez.

• Evacuez la piéce, le bâtiment ou la zone.

• Appelez immédiatement votre fournisseur de gaz depuis

un voisin. Suivez les instructions du fournisseur.

• Si vous ne pouvez rejoindre le fournisseur de gaz,

appelez le service dos incendies.

L’installationetservicedoitêtreexécutéparunqualiﬁéinstal-

leur, agence de service ou le fournisseur de gaz.

WARNING: If the information in this manual is not

followed exactly, a ﬁre or explosion may result

causing property damage, personal injury or loss

of life.

AVERTISSEMENT: Assurez-vous de bien suivre les

instructions donné dans cette notice pour réduire au

minimum le risque d’incendie ou pour éviter tout dom-

mage matériel, toute blessure ou la mort.

Models: EBVI25 & EBVI30

P/N 775,155M Rev. E, 12/2007

WARNINGS

• Hot! Do not touch! The glass and surfaces of this appliance will be hot during operation and will

retain heat for a while after shutting off the appliance. Severe burns may result.

• Carefully supervise children in the same room as appliance.

• If small children are present in the home, it is recommended that this appliance be ﬁtted with a

screen door or screen panel kit. See Page 13 for ordering information.

• Suitable for installation into masonry or factory built ﬁreplaces.

•

Lennox™ gas-burning appliances are designed for use as a supplemental heater. They are not intended for

continuous use as a primary heat source.

A French manual is available upon request. Order P/N 775,155CF.

Ce manuel d’installation est disponible en francais, simplement

en faire la demande. Numéro de la pièce 775,155CF.

Installer: Leave This Manual With The Appliance.

Consumer: Retain This Manual For Future Reference.

DRAFT

11-05-2007

IMPORTANT SAFETY AND

WARNING INFORMATION

READ THIS MANUAL IN ITS

ENTIRETY AND UNDER-STAND

THESE RULES TO FOLLOW FOR

SAFETY.

2NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

WARNING

Do not attempt to alter or modify

theconstructionoftheappliance

or its components. Any modi-

ﬁcation or alteration may void

the warranty, certiﬁcation and

listings of this unit.

WARNING

Improper installation, adjust-

ment, alteration, service or

maintenance can cause injury

or property damage. Refer to

this manual. For assistance or

additional information consult

a qualiﬁed installer, service

agency or the gas supplier.

WARNING

These fireplace Inserts are

vented heaters. Do not burn

wood or other material in these

appliances.

WARNING

Failuretocomplywiththeinstal-

lationandoperatinginstructions

provided in this document will

result in an improperly installed

andoperatingappliance,voiding

its warranty. Any change to this

appliance and/or its operating

controlsisdangerous. Improper

installation or use of this appli-

ance can cause serious injury or

deathfromﬁre,burns,explosion

or carbon monoxide poisoning.

WARNING

Carbon Monoxide Poisoning:

Early signs of carbon monoxide

poisoning are similar to the ﬂu

withheadaches,dizzinessand/or

nausea. If you have these signs,

obtain fresh air immediately.

Have the appliance serviced

by a qualiﬁed technician as it

may not be operating correctly.

Some people are more affected

by carbon monoxide than others.

These include pregnant women,

peoplewithheartorlungdisease

or anemia, those under the inﬂu-

enceofalcohol,andthoseathigh

altitudes.

WARNING

Children and adults should be

alerted to the hazards of high

surface temperatures. Use cau-

tion around the appliance to

avoid burns or clothing ignition.

Youngchildrenshouldbecarefully

supervised when they are in the

same room as the appliance.

Do not attempt to touch the front

enclosure glass with your hands

while the ﬁreplace is in use.

Note:AnOptionalScreenPanelfor

the glass is available (see Page

13 for ordering information).

WARNING

Do not place clothing or other

ﬂammable materials on or near

this appliance.

AVERTISSEMENT

Surveillerlesenfants. Garderles

vêtements,lesmeubles,l'essence

ouautresliquidesà vapeurinﬂam-

mables loin de l'appareil.

WARNING

Do not use these appliances if

any part has been under water.

Immediately call a qualiﬁed,

professional service technician

to inspect the appliances and to

replace any parts of the control

system and any gas controls

which have been under water.

AVERTISSEMENT

Ne pas se servir de cet appareil

s'il a été plongé dans l'eau,

complètement ou en partie.

Appeler un technicien qualiﬁé

pourinspecterl'appareilet rem-

placertoutepartiedusystèmede

contrôle et toute commande qui

ont été plongés dans l'leau.

IMPORTANT

• Provide adequate clearances

around air openings and

adequate accessibility clear-

ance for service and proper

operation.

• Never obstruct the front open-

ings of the appliance.

• Due to high temperatures of

these appliances, adequate

clearances need to be main-

tained from furniture, draper-

ies and other combustibles.

Locate furniture and window

coverings accordingly. The

recommendedclearancezone

fromthefrontoftheappliance

to combustibles is 36 inches

(914 mm). Maintain all other

clearances as outlined in the

Installation Manual.

• Theseappliancesaredesigned

as supplemental heaters.

Therefore, it is advisable to

have an alternate heat source

when installed in a dwell-

ing.

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Input of millivolt model is variable. The rates

are shown in the following table:

Thismillavoltapplianceisdesignedtooperate

on either natural or propane gas. A millivolt

gas control valve with piezo ignition system

provides safe, efﬁcient operation. External

electrical power is required to operate the air

circulation blower.

This appliance complies with National Safety

Standards and is tested and listed by OMNI-

Test Laboratories Inc.; Beaverton, Oregon

(Report No. 116-F-15-5) to ANSI Z21.88

(in Canada, CSA-2.33), and CAN/CGA-2.17-

M91 in both USA and Canada, as vented

gas heaters.

Installation must conform to local codes.

In the absence of local codes, installation

must comply with the current National Fuel

Gas Code, ANSI Z223.1 / NFPA 54 - latest

edition. (In Canada, the current CAN-1 B149

installation code). Electrical wiring must

comply with the National Electrical Code

ANSI/ NFPA 70 - latest edition. In Canada,

the current CSA C22-1 Canadian Electrical

Code - latest edition.

GENERAL INFORMATION

Installation, repair and annual service in-

spection should be performed by a qualiﬁed

service technician.

TABLE OF CONTENTS

Important Safety and

Warning Information....................Page 2

Introduction ......................................Page 3

General Information..........................Page 3

Burn-In Period ..................................Page 4

Lighting Millivolt Appliances.............Page 4

Gas Controls .....................................Page 4

Control Compartment Access ...........Page 4

Operation & Care of Your Appliance..Page 5

Maintenance Procedures...................Page 5

Maintenance Schedule......................Page 7

Front Glass Door Assembly,

Removal and Installation.................Page 8

Burner Adjustments..........................Page 8

Flame Appearance and Sooting.........Page 8

Log Placement Instructions ..............Page 9

Millivolt Appliance Checkout.............Page 12

Blower Operation ..............................Page 12

Fireplace Requirements.....................Page 12

Wiring Diagrams...............................Page 12

Accessory Components ....................Page 13

Lighting Instructions – Millivolt ........Page 15

Replacement Parts List.....................Page 17

Troubleshooting Guide......................Page 19

Product Reference Information.........Page 20

INTRODUCTION

The Insert model covered in this manual is

a B-Vent gas heater designed for residential

application for installation into an existing

masonry or factory built solid-fuel ﬁreplace

using 4" diameter, UL1777 listed aluminum

liner for the exhaust.

The vent must be routed through the existing

ﬁreplace ﬂue system to the vent termination.

Millivolt Models with

MAnnually-Modulated Gas Valves

Nat. Gas Propane

Model No. Input Rate

(BTU/HR)

Input Rate

(BTU/HR)

EBVI25 17,000 to

25,000

19,500 to

25,000

EBVI30 21,500 to

30,000

22,000 to

28,000

Table 1

CONGRATULATIONS ON THE PURCHASE OF YOUR NEW GAS APPLIANCE MANU-

FACTURED BY LENNOX HEARTH PRODUCTS.

When you purchased your new gas-ﬁred heater, you joined the ranks of thousands of

individuals whose answer to their home heating needs reﬂects their concern for efﬁciency

and our environment. We extend our continued support to help you achieve the maximum

beneﬁt and enjoyment available from your new gas-ﬁred heater. It is our goal at Lennox

Hearth Products to provide you, our valued customer, with an appliance that will ensure

years of trouble-free warmth and pleasure.

Thank you for selecting a Lennox Hearth Products gas-ﬁred heater as the answer to

your home heating needs.

Sincerely,

All of us at Lennox Hearth Products

It is imperative that the control compart-

ment,burnersandcirculatingairpassage

ways of the appliance be kept clean.

S'assurerquelebrùleuretlecompartiment

des commandes sont propres. Voir les

instructions d'installation et d'utilisation

qui accompagnent l'appareil.

Table 2 shows the main burner gas oriﬁce

size for the elevations indicated.

Model

No.

Oriﬁce Size Elevation

Feet

(meters)

Nat.

Gas

Prop.

Gas

EBVI25 #41

(.096")

#53

(.0595")

0-4500

(0-1372)

EBVI30 #37

(.104")

1/16"

(.0625")

0-4500

(0-1372)

Table 2

Tables 3 and 4 show the gas pressure

requirements for all models:

Inlet Gas Supply Pressure (all models)

Fuel # Minimum Maximum

Natural Gas 4.5" WC

(1.12 kPa)

10.5" WC

(2.61 kPa)

Propane 11.0" WC

(2.73 kPa)

13.0" WC

(3.23 kPa)

Table 3

Manifold Gas Supply Pressure (all models)

Fuel # Low High

Natural

Gas

(Lo) 1.6" WC

(.40 kPa)

(Hi) 3.5" WC

(.87 kPa)

Propane (Lo) 6.3" WC

(1.57 kPa)

(Hi) 10.0" WC

(2.49 kPa)

Table 4

4NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Test gauge connections are provided on the

frontof the millivoltgas control valve(identi-

ﬁed IN for the inlet and OUT for the manifold

side). See Figures 1 & 2.

This appliance must not be connected to a

chimney or ﬂue serving a separate solid-fuel

appliance.

Burn-in Period

During the ﬁrst few burns of these appliances

there will be some odor due to the curing of the

high temperature paint and burning off of lubri-

cants used in the manufacturing process.

Depending on your use, the burn-in period may

take a few hours or a few days. Do not turn on

blower during Burn-In period.

IMPORTANT

Keep your house well ventilated

during the curing process. The

odor and haze emitted by the

curing process can be quite

noticeable and may set off a

smoke detector.

Figure 1

GAS CONTROL

KNOB

CONVERTIBLE

HI/LO REGULATOR

(adjusts ﬂame height

and heat output)

INLET

PRESSURE

TAP

PILOT

ADJUSTMENT

SCREW

WIRING

TERM-

INALS

OUTLET

PRESSURE

TAP

Model EBVI30

Honeywell Millivolt Gas Valve Controls

TP/TH

PIEZO

IGNITER

TPTH TP TH

IN OUT

Figure 2

MODEL EBVI25

SIT Millivolt Gas Valve Controls

GAS CONTROL

KNOB

INLET

PRESSURE

TAP

OUTLET

PRESSURE

TAP

CONVERTIBLE

HI/LO REGULATOR

(adjusts ﬂame height

and heat output)

PIEZO

IGNITER

GAS CONTROLS

Thesemillivoltappliancesareﬁttedwithaburner

Off/On Switch, located on the side surround

panelasshown in Figure 4 on Page 4. Once the

pilot is lit, and valve knob is in the ON position,

the Off/On switch will control the appliance

Off/On operation. To operate, toggle the switch

between its ON and OFF positions.

Variable Flame Height Adjustment

These millivolt appliances are equipped with

variable gas control valves. Flame height may

be adjusted through a range between ﬁxed low

and high settings by rotating the HI/LO knob on

thevalve(seeFigures1 & 2)whiletheappliance

is in operation.

Lighting Millivolt Appliances

To light millivolt appliances refer to the detailed

lighting instructions found on Page 15 (Eng-

lish) and Page 16 (French). Millivolt appliance

lighting instructions may also be found on the

pull-outlightinginstructionlabelslocatedinthe

control compartment (below glass door).

This appliance must be isolated from the

gas supply piping system (by closing its

individual manual shut-off valve) during

any pressure testing of the gas supply

piping system at test pressures equal to

or less than 1/2 psig (3.5 kPa).

This appliance and its individual shut-off

valve must be disconnected from the gas

supply piping system during any pressure

testingofthat system at pressuresgreater

than 1/2 psig (3.5 kPa).

CONTROL COMPARTMENT ACCESS

Pull down hinged door to access control

compartment (see Figure 3).

Control Compartment Access

Pull down hinged door to access control compartment

Pull down lower

louver (hinged)

Side View of Insert

Figure 3

Figure 4

Burner Off/on Switch and Rheostat Location

If optional surround is installed

Burner Off/On

Switch

Rheostat

(blower

speed

control)

Left Front

surround

Panel

Units with Beveled Surround

Units with Flat Surround

Left Front

surround

Panel

Rheostat

(blower

speed

control)

Burner Off/on

Switch

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. 5

CAUTION

Wear gloves and safety glasses

for protection while doing

required maintenance.

IMPORTANT

Always verify proper operation

after servicing.

WARNING

Turnoff gas and electricalpower

before servicing the appliance.

OPERATION AND CARE OF YOUR

APPLIANCE

Appliance operation may be controlled

through a remotely located optional wall

thermostat or remote control.

Inlieuofremotecontrolorremotewall thermo-

stat operation, the appliance must be operated

directlythroughtheoff/onswitchlocatedonthe

side surround panel (see Figure 4).

If your millivolt appliance is equipped with an

optionalwallthermostatkitorremotecontrol

kit and the pilot is lit (and valve is in the On

position), the appliance main burner may be

turned on and off with the wall thermostat

or remote control.

Always keep the appliance area clear and free

from combustible materials, gasoline and

other ﬂammable liquids.

Remember, millivolt appliances have a

continuous burning pilot ﬂame. Exercise

caution when using products with combus-

tible vapors.

MAINTENANCE

The appliance and venting system should be

thoroughly inspected before initial use and at

least annually by a qualiﬁed service technician.

However, more frequent periodic inspections

and cleanings should be performed by the

homeowner. Homeowner must contact a quali-

ﬁed service technician at once if any abnormal

condition is observed.

Refer to the maintenance schedule on Page

7for maintenance tasks, procedures, recom-

mended frequency and by whom they should

be performed. Always verify proper operation

of the appliance after servicing.

Always turn off the gas and unplug the power

cord to the appliance before cleaning. Before

re-lighting, refer to the lighting instructions

in this manual. Instructions are also found on

pull-out panels located below the glass door in

the control compartment.

Keep lower control compartment clean by

vacuuming or brushing at least twice a year.

More frequent cleaning may be required due to

excessivelintfromcarpeting,beddingmaterials,

etc. It is important that control compartments,

burners and circulating air passageways of the

appliance be kept clean.

Check Burner Flame Appearance

Visually check the ﬂame of the burner periodi-

cally making sure the ﬂames are steady and not

lifting or ﬂoating (see Figure 13 on Page 8).

Glass Cleaning

Note: Clean glass after ﬁrst two weeks of opera-

tion (after Burn-In period is over).

The viewing glass should be cleaned periodi-

cally to remove any build-ups caused from the

following:

• During start-up, it is normal for condensa-

tion to form on the inside of the glass (this

condensation and fog will usually disappear

in a few minutes). This can cause lint, dust

and other airborne particles to cling to the

glass surface.

• Initial curing of the high temperature paint

and burning off of lubricants used in the

manufacturing process may result in a ﬁlm

on the glass.

• A white coating may form on the glass as a

result of impurities and minerals in the fuel.

It is recommended that the glass be cleaned

two or three times during each heating season,

depending on the circumstances present.

Use one of the following to clean glass:

• Non-ammonia based household cleaner

• 50%-50% mix of white vinegar & water

• gas stove glass cleaner

WARNING

Do not attempt to touch the front

enclosure glass with your hands

while the ﬁreplace is in use.

IMPORTANT

Do not use abrasive cleaners

on glass. Never clean the glass

when it is hot.

Servicing Blower

To access the blower assembly for mainte-

nance, adjustment or replacement, see the

following procedure:

1. Unplug 120-volt A.C. power supply to

insert.

2. Shut off gas supply to insert.

3. Remove Glass Door (see Procedure

For Removing Standard Glass Door

Assembly on Page 8).

4. Remove log set, burner and grate.

5. Remove blower access panel and

gasket (see Figure 5 for model EBVI25

and Figure 6 for model EBVI30). Be

careful not to damage the gasket.

Access Panel

w/ Gasket

Figure 6

Model EBVI30

Figure 5

Access Panel

w/ Gasket

Model EBVI25

Remove 10 Screws (use phillips screwdriver)

Remove 12 Screws (use phillips screwdriver)

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Small Area Paint Touch-up

The ﬁnish of the insert body and surround

(optional) is a high-quality powdercoat. Only

use factory supplied powdercoat paint kit for

touch-ups, cat. no. 90L74.

Do not attempt to repaint the insert until the

ﬁnish is completely cured (see Burn-In Period

onPage 4). If the surfacelater becomes stained

ormarred,itmay be lightly sanded and touched

up with spray paint.

PaintisavailableatyourlocalauthorizedLennox

Hearth Products dealer. Never attempt to paint

a hot insert.

Inspect Wiring

Inspect and clean all wire connections. Ensure

that there is no melting or damage. Inspection

should include:

• Terminals at the valve

• Off/On switch

• Wall thermostat, remote control, or control

kit (optional parts)

• Spill switch

Refer to wiring diagrams on Pages 12 & 13.

CAUTION

Label all wires prior to discon-

nection when servicing con-

trols. Wiring errors can cause

improper and dangerous appli-

ance operation.

Check

Connections

Spill Switch

Draft Hood

Figure 10

6. (Model EBVI25) Remove the two hex

head bolts shown in Figure 7.

(Model EBVI30) Remove the two

screws shown in Figure 8, then lift

out air duct channel.

Figure 8

Remove 2 Screws

7. Disconnect wires from the blower.

8. Lift blower up and pull it out from back

opening of ﬁrebox (see Figure 9).

9. To reinstall blower, reverse Steps 1

through 8.

Figure 7

Blower

Remove 2 Bolts

Model EBVI30

Model EBVI25

Lift Out Air

Duct Channel

Figure 9

Blower Assembly

Maintenance Task Accomplishing Person Procedure

Inspecting/Cleaning Burner, Logs

and Controls

Qualiﬁed Service Technician Inspect valve and ensure it is properly operating. Check piping

for leaks. Vacuum the control compartment, ﬁreplace logs and

burner area.

Check Flame Patterns and Flame

Height

Qualiﬁed Service Technician Refer to Figure 13 on Page 8 and verify the ﬂame pattern and

heightdisplayedbytheapplianceconformstothepicture. Flames

must not impinge on the logs.

Inspecting/Cleaning Pilot and Burner Qualiﬁed Service Technician Refer to Figure 13 on Page 8 and Figure 25 on Page 12.Remove

any surface build-up on pilot and burner assembly. Wipe the

pilot nozzles, ignitor/ﬂame rod and hood. Ensure the pilot ﬂame

engulfs the ﬂame sensor as shown.

Checking Vent System Qualiﬁed Service Technician Inspect the vent system at the top and at the base (within the

ﬁrebox) for signs of blockage or obstruction. Look for any signs

of dislocation of the vent components.

Appliance Checkout Qualiﬁed Service Technician Perform the appropriate appliance checkout procedure detailed

in this manual.

Replacing Rockwool Ember Materials Homeowner/Qualiﬁed Services Techni-

cian

Remove old ember materials and vacuum the rockwool place-

ment area. Place new rockwool as described on Page 11 (see

Figure 23).

Periodically (After the Burning Season)

Maintenance Task Accomplishing Person Procedure

Cleaning Firebox Interior Homeowner Carefullyremovelogs,rockwoolandandvermiculite. Vacuumout

interiorofthe ﬁrebox. Clean ﬁrebox walls and log grate. Replace

logs, Rockwool and vermiculite as detailed in this manual.

Check Flame Patterns and Flame

Height

Homeowner Refer to Figure 13 on Page 8 and verify the ﬂame pattern and

heightdisplayedbytheapplianceconformstothepicture.Flames

must not impinge on the logs.

Checking Vent System Homeowner Inspect the vent system at the top and at the base (within the

ﬁrebox) for signs of blockage or obstruction. Look for any signs

of dislocation of the vent components.

Cleaning Front Door Window Homeowner Clean as necessary following the directions provided in this

manual. DO NOT TOUCH OR ATTEMPT TO CLEAN GLASS WHILE

HOT.

Annually (Before the onset of the Burning Season)

MAINTENANCE

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

PROCEDURE FOR REMOVING STANDARD

GLASS DOOR ASSEMBLY

Burner Flame Appearance

BURNER ADJUSTMENT

Flame Appearance and Sooting

Properﬂame appearanceisaﬂame whichisblue atthebase andbecomes

yellow/orange in the top of the ﬂame. When the insert is ﬁrst lit, the entire

ﬂame may be blue and will graduallay turn yellow/orange during the ﬁrst

6-8 minutes of operation. If after 6-8 minutes the ﬂame stays blue, or if

the ﬂame is orange with evidence of sooting (black tip), the air shutter

may require adjustment.

An appliance operated with an air shutter opening that is too large will

exhibit ﬂames that are blue and transparent. These weak, blue and

transparent ﬂames are termed anemic. If the air shutter opening is too

small, sooting may develop.

Sooting is indicated by black puffs developing at the tips of very long

orange ﬂames. Sooting results in black deposits forming on the logs,

appliance inside surfaces and on exterior surfaces adjacent to the

vent termination. Sooting is caused by incomplete combustion in the

ﬂames and lack of combustion air entering the air shutter opening. To

achieve a warm yellow to orange ﬂame that does not soot, the shutter

opening must be adjusted between these two extremes.

No smoke or soot should be present. Reposition the logs if ﬂames

impinge on any of them. If the logs are properly positioned and

sooting conditions exist, the air shutter opening on the main burner

tube should be adjusted.

Figure 13 EBVI25 Shown

Release latch on

each side (below door)

Remove the front door assembly from insert as follows:

1) Open the two latches below the glass door as shown in Figures

11 & 12.

Figure 11

2) Swing the bottom of the door outward (see Figure 12)and lift it

off of ﬁrebox top. Set door aside in a safe place.

Figure 12

Latches

Glass Door

Top

Flange

Door

Frame

Firebox Floor

Bottom Vee-ﬂange

Door Frame

Glass Door

WARNING

Handle glass door with extreme care! The glass

door assembly is susceptible to damage. Do not

scratch while handling or while reinstalling.

WARNING

Neveroperateunitwithoutthefrontglassdoorpanel

in place and secure.

IMPORTANT

Ensure that the front glass panel is in place and

sealed during adjustment.

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. 9

Iftheburnerﬂameappearancediffersgreatly

from what is shown in Figure 13 (see Burner

Flame Appearance), some adjustment from

thefactory setting fortheairshuttergapmay

be necessary (to compensate for variables

in the installation and fuel such as, BTU

value/composition, gas pressure, speciﬁc

gravity of gas, altitude, etc.).

See Table 5 for Burner Air Shutter Adjust-

ment Guidelines.

Initially, always position the air shutter to the

factorysettingasshowninFigure14 (adjust-

mentrodislocatedinthelowercontrolarea).

This can be done by moving the adjustment

rodupordownaccordingly. Allowtheburner

to operate for at least 15 minutes. Observe

the ﬂame continuously. If it appears weak

or sooty as previously described, adjust the

air shutter to a more open position until the

proper ﬂame appearance is achieved.

Burner Adjustment Procedure

Burner Air Shutter Adjustment

Adjustment Rod Up

(1/8" Open Position)

Air Shutter

Burner Tube

Adjusting Set Screw

Adjustment Rod Down

(full open position)

Figure 14

MAIN BURNER FACTORY AIR

SHUTTER OPENING SETTING

Model Gas Type Air Shutter Gap

EBVI30 Natural Gas 5/16" (7.94mm)

Propane 1/2" (12.7mm)

EBVI25 Natural Gas 1/16" (1.59mm)

Propane 1/2" (12.7mm)

WARNING

Air shutter adjustment should

only be performed by a qualiﬁed

professional service technician.

CAUTION

The adjustment rod and nearby

appliancesurfacesare hot. Exer-

cise caution to avoid injury while

adjusting ﬂame appearance.

CAUTION

Carbon will be produced if the air shutter is closed too much. Any

damage due to carboning resulting from improperly setting the air

shutter is not covered under the warranty.

LOGS, VERMICULITE AND EMBERS

Carefully install the seven-piece log set into the ﬁrebox as shown in these instructions. All

logs should ﬁt onto corresponding pins and/or log stoppers. This will ensure a proper ﬂame

and safe combustion.

Note: Place some vermiculite around burner before installing logs (see Figure 24). The entire

bag of vermiculite will NOT be used.

The following chart is provided to aid you in achieving the correct air shutter adjustment

for your installation.

Table 5

Air Shutter Adjustment Guidelines

Amount of

Primary Air

Flame Color Air Shutter

Adjustment

If air shutter is

closed too far

Flame will be orange Airshuttergap should

be increased

If air shutter is open

too far

Flame will be blue Airshutter gapshould

be decreased

WARNING

If logs are not installed according to the directions shown here, ﬂame

impingement and improper combustion could occur and result in soot

and/or excessive production of carbon monoxide (CO) - a colorless,

odorless, toxic gas.

Top Left Log

Front Center Log

Top Right Log

Rear Log

Front Right Log

Front Left Log

Center Log

Figure 15

Installation Instructions

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

1. Place the rear log onto the two corresponding locating pins at the

back of the ﬁrebox as shown in Figure 16.

2. Place the Front Right Log onto the two corresponding locating pins

as shown in Figure 17.

3. Place the Center Log onto the two corresponding locating pins as

shown in Figure 18.

Figure 16 Rear Log

Figure 17 Front Right Log

Figure 18 Center Log

4. Place the Front Left Log onto the two corresponding locating pins

as shown in Figure 19.

5. Install the Top Left Log onto the corresponding locating pin and

indentation on Center Log as shown in Figure 20.

6. Install the Front Center Log over the Front Right Log. The front

of log will rest on the burner and the back of log will rest on rear

log as shown in Figure 21.

7. Install the Top Right Log into the corresponding indentations on

Front Center Log and front right twig as shown in Figure 22.

Figure 19 Front Left Log

Figure 20 Top Left Log

Figure 21 Front Center Log

Otros manuales para Elite series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Chimenea de interior de Lennox

Lennox

Lennox Dave Lennox Signature Series Manual de usuario

Lennox

Lennox MPB3328CNM-B Manual de usuario

Lennox

Lennox MPD Series Manual de usuario

Lennox

Lennox RHAP54N Manual de usuario

Lennox

Lennox MPDR-3328CPE Manual de usuario

Lennox

Lennox Signature Montebello DLX Series Manual de usuario

Lennox

Lennox MP03-VDLPM Manual de usuario

Lennox

Lennox Montebello DLX Series Manual de usuario

Lennox

Lennox MPB35ST-NM-B Manual de usuario

Lennox

Lennox LSM40ST-N Manual de usuario

Lennox

Lennox ADAGIO-MN Manual de usuario

Lennox

Lennox Dave Lennox Signature Montebello LSM45EN-PV Manual de usuario

Lennox

Lennox Merit Series Manual de usuario

Lennox

Lennox ELITE TM-4500 Manual de usuario

Lennox

Lennox MPDT33RNM Manual de usuario

Lennox

Lennox Scandium-NG Manual de usuario

Lennox

Lennox MPD35ST-NM-B Manual de usuario

Lennox

Lennox MP-42OD Manual de usuario

Lennox

Lennox MPE-27 Manual de usuario

Lennox

Lennox ELITE SERIES LA41CF Manual de usuario

Lennox

Lennox MERIT PLUS SERIES Manual de usuario

Lennox

Lennox NV35IN Manual de usuario

Lennox

Lennox Merit MPE36 Manual de usuario

Lennox

Lennox MPDP35IN Manual de usuario

Manuales populares de Chimenea de interior de otras marcas

Brigantia

Brigantia 35-DVRS31N-2 Manual del propietario

Nordpeis

Nordpeis Bergen Manual de usuario

Superior

Superior BCT2536TMN Manual de usuario

Quadra-Fire

Quadra-Fire 5100I-GD-B Manual de usuario

Renaissance

Renaissance RUMFORD 1000 Manual de usuario

Lacunza

Lacunza IV-800 Manual de usuario

Baxi

Baxi 940 Instrucciones de uso

Dru

Dru Maestro 60/2 Tall RCH Manual de usuario

Diamond Fireglass

Diamond Fireglass SS-O22 Manual de usuario

HearthStone

HearthStone Windsor Bay 8830 Manual de programación

Napoleon

Napoleon ASCENT B42 Manual de usuario

Enviro

Enviro E33GI Manual de usuario

Smeg

Smeg L30 FABE Instrucciones de montaje

KEDDY

KEDDY K700 Manual de usuario

Godin

Godin 3451 Manual de usuario

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manual de usuario

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manual de usuario

Desa

Desa CCFPDFT Manual de operación