LENCO L-175 Manual de usuario

L-175

Direct drive glass turntable

User Manual

www.lenco.com

Table of content

Table of content ---------------------------------------------------------------------- 2

Description ---------------------------------------------------------------------------4-5

Initial starting-up ---------------------------------------------------------------------- 6

Mount and adjust --------------------------------------------------------------------- 6

Mains connection --------------------------------------------------------------------- 7

Amplifier connection ----------------------------------------------------------------- 7

Playing a record ---------------------------------------------------------------------- 8

Record to PC -------------------------------------------------------------------------- 8

Maintenance --------------------------------------------------------------------------- 9

To replace the stylus ---------------------------------------------------------------- 9

To disassemble the cartridge ----------------------------------------------------- 9

Important recommendations ------------------------------------------------------- 9

Audacity quick guide ---------------------------------------------------------- 10-25

Dear customer,

Thank you for buying this Lenco product. Quality and usability is our top

priority. In order to let you fully enjoy this turntable, we have manufactured

this product using high quality standards, materials, components, and care.

Please read all safety instructions and national restrictions, before

you use this turntable.

Note:

This user manual was printed prior to the development of this product.

When operability or other functions needed improvement, priority went to

the product specification itself, and not to this manual.

In such instances, the instruction manual may not entirely match all the

functions of the actual product. Therefore, the actual product and

packaging, as well as the name and illustration, may differ from the manual.

The screen shown as an example in this manual may differ from the actual

screen display.

Lenco is not liable for any consequential damage.

Description

1. Counterweight

The counterweight is used for precise adjustment of the stylus

pressure on the vinyl, to properly balance the tone arm.

2. Anti-Skating Control

Use this to set the anti-skating function of the tone arm.

3. Tone arm Lever

Use this lever to lower and raise the tone arm.

4. Tone arm Lock (arm rest)

Use this to lock the tone arm in place when not in use.

5. Headshell

This holds the stylus (“needle”) in place and provides protection by

means of its removable stylus protection cap (not shown)

6. Platter:

Place the record here when playing.

7. 33/45 RPM Switch (33/STOP/45):

Select 33 or 45 rpm for playing a vinyl, switch to “STOP” to pause the

playing. Switch to 33 or 45 again, to continue the playing from the

pause point.

8. Signal Connectors

Plug in the RCA cable, and connect the cable to audio amplifier.

9. Pre-Amp ON/OFF selector

*ON: Connect the RCA cable to LINE-IN terminal of amplifier.

*OFF: Connect the RCA cable to PHONO-IN terminal of amplifier.

10. USB port

Connecting to PC for recording the music from vinyl to PC.

- With Full-Speed Transceivers

- Fully Compliant With USB 1.1 Specification

11. Auto Stop Switch

While the tone arm playing to the end of the record, it will automatically

stop. The records have various ending points, if the record is auto-stop

before playing to the end, please switch off the auto-stop function.

12. Power supply jack:

To plug-in DC24V/1A switching adaptor for power supply.

13. Power Switch:

During PAUSE mode (33/STOP/45 switch is on “STOP” position), the

motor is still activated, switch off the player after use to save energy.

When installing the L-175 please make sure not to place it directly on top

of your Amplifier. (Amplifiers are known to cause hum noise on turntables.)

Initial starting-up

Mount and adjust

1) Place the aluminum turntable platter.

2) Insert the counterweight on the end of the tone arm, lock it into place.

3) Adjusting the stylus pressure

Turn the anti-skating knob counter-clockwise to “0”.

Pull down the protective cover of the stylus.

Place the lever for the tone arm lift in the front position.

Open the tone arm lock. Seize the handle of the tone arm and lead it

to just before the turntable platter so that it can be moved upwards

and downwards. (Be careful not to hit the stylus against anything.)

4) Turn the counterweight until the tone arm remains in a horizontal

position and does not move upwards or downwards. If the tone arm

moves upwards: Turn the counterweight counter-clockwise. If the tone

arm moves downwards: Turn the counterweight clockwise.

5) Put the tone arm back onto the arm rest and lock it.

6) The counterweight is with a rotary ring with a scale. The white line on

the tone arm points to a value on this scale. Without turning the

counterweight, only turn the ring to “0”

7) The scale indicates the stylus pressure in grams. The pressure of the

stylus supplied with this turntable is 3 g, turn the counterweight

counter-clockwise to “2.5”. If another stylus is used, adjust the stylus

pressure indicated in the corresponding specifications of the stylus.

8) Adjusting the anti-skating facility

When playing a record, forces occur on the stylus which are

compensated by the anti-skating facility. For this purpose, adjust the

anti-skating knob from “0” to the value equals to the stylus pressure,

with for the supplied stylus system , it’s “2.5”.

Mains Connection

An external switching power adaptor (DC24V/1A) is supplied with this

turntable. Your unit is ready to be connected to a main voltage of

110V/60Hz or 230V/50Hz.

Amplifier Connection

There is a Phono/Line selector next to the RCA jack on the rear panel of

the turntable.

If your amplifier has “PHONO” input, switch the selector to “PHONO”,

and connect the RCA plug to the PHONO INPUT of your amplifier.

If your amplifier hasn’t “PHONO” input, switch the selector to “LINE”,

and connect the RCA plug to the “LINE” input of your amplifier.

Red plug into R channel input, White plug into L channel input.

With the PRE-AMP switch at ON never connect to a Phono input.

Audio will be strongly distorted then and there is a risk that

Amplifier and/or speakers will be damaged.

Playing a record

1) Place the record on the turntable. If it is a 45 rpm, you need to place

the adaptor on the record spindle.

2) Choose the playing speed, record

3) Release the pick-up arm clip.

4) Place the cartridge vertically over the first track of the record the

turntable.

5) When it play to the end of the record, the platter is auto-stop, push the

lift button to lift the tone arm and lead it back to the arm rest.

6) When the auto stop system is activated, the platter will stop in a few

seconds, if you want to repeat playing the same side of the vinyl, need

to release the auto-stop as following:

i) Move the tonearm to arm rest, and them put it on the track you to

play. Or,

ii) Switch the 33/STOP/45 knob to “STOP” , then switch to 33 or 45.

7) If you want to pause the playing, switch the knob on the left side to

“STOP”, and switch it to 33 or 45 to continue the playing.

8) After finish the playing, please switch off the power to save energy.

Record to PC

Connect USB to PC for editing the music with your favorite digital editing

software.

With this unit, we offer you a disc with a PC music editing program, please

refer to the instructions attached to this manual for the operation.

Maintenance

TO REPLACE THE STYLUS (FIG.A)

-Put the rest (11) clip on the pick-up arm.

-Remove the protective cap from the stylus.

-Pull the stylus in the direction of arrow (A) and remove it.

-Put in the new stylus following the reverse procedure.

-Replace the protective cap on the stylus.

TO DISASSEMBLE THE CARTRIDGE (FIG.B)

-Put the rest clip into the pick-up arm.

-Remove the stylus (see section above).

-Release the pick-up head, push the cartridge in the direction of

arrow.

-Disconnect the four link wires at the level of the pick-up head.

TO INSTALL NEW CARTRIDGE

-Connect the four link wires as shown in figure.

-Push the cartridge into head shell

-Re-position the stylus

-Replace the protective cap on the stylus.

Important Recommendations

We advise you to clean your records using a rag impregnate with an

antistatic product for maximum enjoyment of your records and also to

make them last.

We would also point out that for the same reason your stylus should be

replaced periodically (approximately every 250 hours)

Dust the stylus from time to time using a very soft brush dipped in alcohol

(brushing from back to front of the cartridge)

WHEN TRANSPORTING YOUR RECORD PLAYER DO NOT FORGET

TO:

Replace the protective cap on the stylus.

Put the rest clip into the pick-up arm.

AUDACITY QUICK GUIDE (PC editing program)

Before Starting the Software

Make sure that your USB turntable is plugged into the computer and both

the computer and the turntable are plugged in and switched on.

To Install Software (PC)

1. Plug in your turntable to an AC outlet and connect the USB port

on the Turntable to the USB port of your computer.

2. Turn on the power switch to your turntable.

3. Windows system will detects a new device and that it is available

to use.

4. Insert the CD that came with your USB turntable.

5. Run the file “install audacity-win-1.2.4b.exe” to install Audacity

software. Once installed, run the Audacity program.

To Install Software (MAC)

1. Insert the included CD

2. Open the CD icon on the desktop.

3. Drag the installation folder for audacity to your hard drive. We

recommend that you move the folder to your “Applications” folder.

4. A window will come up which shows the files copying.

5. EJECT the CD.

6. Open “Audacity” from where you moved it to on your hard drive.

Software Configuration

1. Click on Microphone in the drop down menu and select “Stereo Mix”

Figure 1: Select Stereo Mix

2. Select the “Edit” menu and then “Preferences”

Tabla de contenidos

Otros manuales de Placa giratoria de LENCO

LENCO

LENCO LS-101BK Manual de usuario

LENCO

LENCO Classic Phono TCD-2570 Manual de usuario

LENCO

LENCO 8711902044598 Manual de usuario

LENCO

LENCO LS-50 Manual de usuario

LENCO

LENCO L-85 Manual de usuario

LENCO

LENCO LS-40 Manual de usuario

LENCO

LENCO L-80 USB - Manual de usuario

LENCO

LENCO TCD-990 Manual de usuario

LENCO

LENCO L-30 Manual de usuario

LENCO

LENCO LS-300 Manual de usuario

LENCO

LENCO Classic Phono TCD-2570WD Manual de usuario

LENCO

LENCO Classic Phono TT-34 Manual de usuario

LENCO

LENCO LS-300 Manual de usuario

LENCO

LENCO Classic Phono TT-41 Manual de usuario

LENCO

LENCO L-92 Manual de usuario

LENCO

LENCO L-3808 Manual de usuario

LENCO

LENCO LS-500 Manual de usuario

LENCO

LENCO L-82 Manual de usuario

LENCO

LENCO LS-50 Manual de usuario

LENCO

LENCO LS-500OK Manual de usuario

LENCO

LENCO LS-100WD Manual de usuario

LENCO

LENCO LS-500BK Manual de usuario

LENCO

LENCO Classic Phono HOG075 Manual de usuario

LENCO

LENCO Xemio-560 Manual de usuario

Manuales populares de Placa giratoria de otras marcas

Gemini

Gemini CDT-05 MKII Manual de usuario

Rotel

Rotel RP-820 Manual de usuario

Shuman

Shuman MC-250BT Manual de usuario

Stanton

Stanton STR8-150 Manual de usuario

Audio Technica

Audio Technica AT-LPW40WN Manual de usuario

Crosley

Crosley McQueen CR7011-GY Manual de usuario

Reloop

Reloop SMP-1 Manual de usuario

auna

auna TT-Classic Plus Manual de usuario

COMO AUDIO

COMO AUDIO Turntable Analog Manual de usuario

Dual

Dual 1009 F Manual de usuario

REED

REED Muse3C Manual de usuario

AXIOMTEK

AXIOMTEK OPS883-H Series Manual de usuario

Pioneer

Pioneer PL-71 Manual de usuario

Vestax

Vestax PDX-a1 Manual de usuario

Denon

Denon DP-400 Manual de usuario

Dual

Dual 504 Manual de usuario

Audio-Techica

Audio-Techica AT-LP60XBT Manual de usuario

Goldring

Goldring G99 Manual de usuario