Leister Diode S Manual de usuario

LEISTER Diode S, Diode PID

Hot Air Tool

Please read operating instructions carefully

before use and keep for further reference.

• The LEISTER Hot Air Pistol Diode S, Diode PID is designed for continuous

operation and is suitable as a hand tool or for building into machines, instal-

lations and appliances

•Welding of thermoplastic materials and also single-ply flexible plastics and

modified bitumen in the form of boards, tubes, profiles, lining membranes,

coated materials, films, foams, tiles, and sheets. The following procedures

are possible: overlap welding, welding with rod, with tape, butt welding

and melt welding

•Heating-up for forming, bending and sealing of thermoplastic semi-

finished materials and plastic granules

•Drying of water-damp surfaces

•Shrinking of heat-shrink sleeves, films, tapes, solder sleeves and moulded parts.

•Soldering copper pipes, solder joints and metal foils

•Activating/dissolving of solvent free adhesives and fusion adhesives.

• Separating and fusing synthethic fibres and fabrics

• Removing plastic mould flash and putting a shine on plastic surfaces

LEISTER Diode PID

• Temperature electronically

steplessly controlled

• Digital display of SET and

ACTUAL value °C

(in °F on request)

• Air flow monitoring

• Element protection

• Heat protection tube

LEISTER Diode S

• Temperature steplessly

adjustable

• Element protectoion

• Heat protection tube

OPERATING INSTRUCTIONS

APPLICATION

LEISTER Process Technologies, Riedstrasse, CH-6060 Sarnen/

Switzerland

Tel. +41- 41 662 74 74 Fax +41- 41 662 74 16

www.leister.com [email protected]

Voltage V~

Capacity W

Frequency Hz

Temperature °C

Air flow l/min.

Air pressure Pa

Weight g

Size mm

42, 100, 120, 230

900, 1350, 1600, 1600

50/60

20 – 600

min. 40

max. 10 5

(

dynamic)

425, 1150 with 3 m cord and 3 m air hose

265 x Ø 40

Mains voltage cannot

be switched ove

TEST SIGNS

TECHNICAL DATA

105 Pa = 1 bar

This tool is CCA certificated (CENELEC Certification Agreement).

Electrical safety: double insulated

Danger to life when opening the tool, as live compo-

nents and connections ar exposed. Unplug the tool

before opening it.

Incorrect use of hot air blowers can cause fire and

explosion hazard, especially near combustible materials

and explosive gases.

The tool must be operated with supervision. Warmth

can reach combustible materials, which are out of sight.

For personal protection on building sites we strongly

recommend the tool be connected to a GFCI (Ground

Fault Circuit Interrupter) or a RCCB (Residual Current

Circuit Breaker) .

The voltage rating stated on the tool must correspond to

the line/mains voltage.

Do not touch the element housing and nozzle when

they are hot as they can cause burns. Let the tool cool

down. Do not point hot air flow in the direction of

people or animals.

Protect tool from damp and wet.

120

230

WARNING

CAUTION

Operating Condition

• Air supply

The Hot Air tool Diode «S», Diode «PID» needs either the High Pressure Blower

LEISTER Minor, Longlife or Robust for air supply. In dusty air, air filter must be fitted.

When using compressed air, an oil and water filter must be connected. The air flow

can be steplessly adjusted with the LEISTER air flow adjuster attached to the

blower.

•As required, fit appropriate nozzle.

• Connect tool to the mains.

• Adjust the hot air temperature by use of the potentiometer (3).

The themperature can be checked with a thermocouple about 5 mm inside the nozzle, when using round

nozzles in the centre of the nozzle, when using draw nozzles in the main nozzle opening. The diameter of

the thermocouple must not be more than 1 mm max. (in accordance with DVS 2208 part II).

ATTENTION

•The Hot Air tool should be placed on a heat resistant surface or use LEISTER tool

stand . The tool must not be operated without air supply.

•Allow the Hot Air tool to warm up for about 3 min.

Digital-display (8)

Description of tool

USAGE LEISTER Diode S, Diode PID

1. Cord to mains

2. Air hose internal Ø 14 mm

3. Potentiometer for

temperature adjustment

4. Hose clamp

5. Handle

6. Tapered element housing

7. Heat protection tube

8. Digital display of SET and

ACTUAL value

SET value

Resolution 2/3 °C / 5 °F

Air-Error

when air flow falls below

minimum

Sensor Error

when max. temperature

is exceeded in build-up

phase

Operation

•The LEISTER Company, as well as the Service Centres, offer free training courses

and advice in all areas of application (see page 1).

• Allow the tool to cool down after use.

Change of nozzles

•Before changing nozzles, allow the tool to cool down, or use only combination

pliers/spanner.

•Do not touch hot nozzle and make sure to put it only on a heat resistant surface,

because of the fire hazard.

•Only LEISTER nozzles should be used.

• Tool stand

• PVC air hose Ø 14 mm

•Hose clamp for air hose Ø 14 mm

•Repairs should only be carried out by authorised LEISTER Service Centres. They

guarantee a specialised and reliable Repair Service within 24 hours using original

spare parts lists.

•Guarantee and liability will be in accordance with the guarantee certificate as

well as the current valid general business and sales conditions.

•The LEISTER Company rejects any guarantee claims for tools which are not in their

original condition. The tools must never be altered or changed.

Technical data and specifications are subject to change without prior notice.

Your authorised Service Centre is:

GUARANTEE AND LIABILITY

SERVICE AND REPAIR

TYPES

ACCESSORIES

BA DIODE S/DIODE PID/06.2001/GB

Tapered element

housing with heat

protection tube for

push-fit LEISTER

nozzles.

Element housing

with heat tube

protection for

screw-on LEISTER

nozzles

Tool stand

LEISTER Process Technologies, Riedstrasse, CH-6060 Sarnen/

Switzerland

Tel. + 41- 41 662 74 74 Fax +41- 41 662 74 16

www.leister.com [email protected]

Otros manuales para Diode S

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Herramientas eléctricas de Leister

Leister

Leister TRIAC AT Manual de usuario

Leister

Leister TRIAC S Manual de usuario

Leister

Leister TRIAC AT Manual de usuario

Leister

Leister GHIBLI AW Manual de usuario

Leister

Leister WELDPLAST S6 Manual de usuario

Leister

Leister TRIAC ST Manual de usuario

Leister

Leister SONORA S1 Manual de usuario

Leister

Leister Diode Manual de usuario

Leister

Leister TRIAC AT Manual de usuario

Leister

Leister TRIAC S Manual de usuario

Leister

Leister SOLANO AT Manual de usuario

Leister

Leister Electron Manual de usuario

Leister

Leister MINIFLOOR Manual de usuario

Leister

Leister Hot-Jet S Manual de usuario

Leister

Leister TRIAC AT Manual de usuario

Leister

Leister TRIAC ST Manual de usuario

Leister

Leister SOLANO AT Manual de usuario

Leister

Leister ELECTRON ST Manual de usuario

Leister

Leister UNIROOF 700 Manual de usuario

Leister

Leister TRIAC ST Manual de usuario

Leister

Leister GHIBLI AW Manual de usuario

Leister

Leister TRIAC ST Manual de usuario

Leister

Leister TRIAC AT Manual de usuario

Leister

Leister TRIAC AT Manual de usuario

Manuales populares de Herramientas eléctricas de otras marcas

AEG

AEG OMNI-JS Manual de usuario

SIP

SIP 01533 Manual de usuario

Ribimex

Ribimex PRS499 Manual de usuario

3M Fiber Optic Connector Crimp Tool Manual de usuario

Ryobi

Ryobi P524 Manual de usuario

ROJEK

ROJEK FSN 300A Manual de usuario

Kemper

Kemper 1740PRO Manual de usuario

WABCO

WABCO OptiTire Manual de usuario

EINHELL

EINHELL TE-MS 18/210 Li Manual de usuario

Orgapack

Orgapack OR-T 85 Guía rápida

TOUGHCUT

TOUGHCUT Diamond 400 Manual de usuario

Yaros

Yaros PB-3603 Manual de usuario

Fein

Fein BSS 2.0 E Guía de configuración

Baileigh Industrial

Baileigh Industrial SS-2725 Manual de usuario

Milwaukee

Milwaukee 2674-20 Manual de usuario

Fein

Fein BLs 1.6 Manual de usuario

Princess

Princess Electric Multi Sharpener Manual de usuario

FOREDOM

FOREDOM K.1050 Manual