Leica EM-GP Manual de usuario

Updated 5/23/19

Leica EM-GP & GP2 User Guide

●Users must wear protective gloves and goggles when handling liquid nitrogen and ethane

●Setup of the EM-GP takes 30 - 60 minutes. Please plan in advance.

●Shutdown of the EM-GP takes 1 - 2 hours. Please check if you are the last user of the day. If you are not,

please coordinate with the next user.

1. Turn the machine on (power switch at back side of machine).

2. Place the black ethane cup and the silver transfer container into the dewar chamber (usually stored inside

of fume hood).

3. Fill the humidifier with 60 mL distilled water.

4. Fill dewar chamber with LN2until 100% full.

a. refill every ~20 minutes

5. Once the cryogen container temperature < -175℃, liquefy ethane gas until black container full

a. refill 2 - 3 times as ethane will warm up container temp no longer liquefy

6. Fill silver transfer container with liquid nitrogen.

a. refill every ~5 minutes

7. Gently transfer cryo gridbox into silverver transfer container. Refill liquid nitrogen.

8. Setup environmental chamber settings

a. TC= 4℃- 25℃(will only go as low as 7℃)

b. HR= 90 - 99% (~15 minutes); NOTE-

humidifier will only run when TC is reached

c. Setup temperature of cryogen = -175℃

9. Setup blotting parameters

a. On main screen, click the long rectangular

grey box in the upper left side (P1

___/1.0/___).

b. Select option Nr. 1 (see image →). This is

the standard recipe used at the NYSBC. You

are welcome to make your own recipe, but

DO NOT change Nr. 1 recipe.

c. Select “OK” to exit screen

10. Setup tweezer/blotter position parameters. The 2 main settings that need to be adjusted are “blotter

settings” and “grid blot position”.

a. On main screen, select “Setup” button

b. Blotter settings

c. Click “Adjust”

d. Lower chamber? OK

e. Select “Blot Position”

i. Using binoculars and adjust buttons, move blotter closer or further from grid to optimize

contact (218 works well for us)

ii. Select “Back” when done

f. Grid Blot Position

i. Click “Blot Position”

ii. Using microscope and adjust buttons, move tweezer up or down from blotter to optimize

contact (3.6mm works well for us)

iii. Select “Back” when done

g. Select “Prepare” to exit screen

11. Freeze grid (practice first with a dummy grid and water)

Updated 5/23/19

a. Add new blotting paper and secure using magnetic ring. Mark blotting paper with pencil to track

rotation of paper. Switch blotter paper every 4 grids.

b. Load forceps with carbon side facing the

blotting papers (tweezer needs to grab a

significant portion of the grid to ensure good

blotting; see image →)

c. Select “Lower chamber/R”

d. Add 3 uL sample to right side of grid

e. Incubate 30 seconds

f. Select “Rotate home, Blot/A-Plunge”

g. Transfer grid to box

h. Repeat a - f until done.

SHUTDOWN

If you are the last user for the day, then continue to steps below. If not, then top off nitrogen in dewar, cover

nitrogen dewar with a kimwipe (to prevent frosting) and let next user know you are done.

●Remove forceps, wipe them down and put in storage

●Empty water from humidifier

●Open environmental chamber door

●Discard blotting paper and store magnetic ring

●Remove both cryogen containers and transfer to fume hood

●Discard H2O from chamber for GP2 before initiating Backout

●Click “Bake Out” for 1 hour (default)

●This takes ~ 2 hours total

●When bakeout done, lower chamber and turn machine off

●Above photo is H2O

holding Chamber, H2O must be

discarded during bakeout or for

next user when not baking out.

Updated 5/23/19

●LEAVE THE LEICA EM-GP BENCH LOOKING LIKE THIS:

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de laboratorio de Leica

Leica

Leica RM2125 Manual de usuario

Leica

Leica CV5030 Manual de usuario

Leica

Leica VT1000S Manual de usuario

Leica

Leica VT1000 S Manual de usuario

Leica

Leica CV5030 Manual de usuario

Leica

Leica EM CPD300 Manual de usuario

Leica

Leica HistoCore SPECTRA CV Manual de usuario

Leica

Leica ST5020 Manual de usuario

Leica

Leica GLOW400 Manual de usuario

Leica

Leica AutoStainerXL Manual de usuario

Leica

Leica RM2245 Manual de usuario

Leica

Leica RM2125RTS Manual

Leica

Leica BLK3D Manual de usuario

Leica

Leica CM3600 XP Manual de usuario

Leica

Leica L5 FL Manual de usuario

Leica

Leica GS10 Manual de usuario

Leica

Leica CM1520 Manual de usuario

Leica

Leica HistoCore Water Bath Manual de usuario

Leica

Leica EM TXP Manual de usuario

Leica

Leica RM2255 Manual de usuario

Leica

Leica CV5030 Manual de usuario

Leica

Leica RM CoolClamp Manual de usuario

Leica

Leica TCS SP8 Manual de usuario

Leica

Leica ThermoBrite S500 Manual de usuario

Manuales populares de Equipo de laboratorio de otras marcas

Qiagen

Qiagen DML 3000 Manual de usuario

Queensgate

Queensgate NANOSCAN OP400 Manual de programación

Conviron

Conviron GEN1000-GE Manual de usuario

Parr Instrument

Parr Instrument 4560 Manual de instrucciones

IKA

IKA IC control Manual de usuario

Integra

Integra DOSE IT Manual de usuario

Agilent Technologies

Agilent Technologies 5800 ICP-OES Manual de usuario

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Manual de usuario

NI PXI-5422 Manual

Collomix

Collomix Aqix Manual de usuario

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Manual de usuario

Ocean Insight

Ocean Insight FLAME-NIR+ Manual de usuario

Parker

Parker ALIGN-MG-NA Manual de usuario

BD 644787 Manual de usuario

DENTAURUM

DENTAURUM Compact Megaplus Manual de usuario

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Manual de usuario

VWR

VWR SAS Super IAQ Manual de usuario

illumina

illumina MiSeqDx Manual de usuario