LEGRAND Niky 600 Manual de usuario

Niky 600/800

Index

1 Introduction 14

2 Conditions of use 14

3 Installation 15

4 Signals and controls 15

5 Overload and self-shutdown 16

6 Features 16

7 Changing batteries 17

8 Possible malfunctioning 18

9 Technical features 19

1 Introduction

This manual contains information for users of the Niky 600/800 models.

You are advised to read this handbook carefully before installing your uninterruptible power

supply, meticulously following the instructions given herein.

The UPS NIKY is only been made for civil or industrial use; it is not in conformity with the standards

for electro-medical equipment.

• The UPS NIKY has been designed to supply data processing equipment. The load applied must

not exceed the one indicated on the rear label of your UPS.

• The ON/OFF button of your UPS does not electrically isolate the internal parts. To isolate your

UPS unplug it from the mains power socket.

• Do not open the UPS container since there may be parts inside with dangerously high voltage

even when the mains plug is disconnected; there are no parts inside that the user can repair.

• The UPS NIKY has been designed to work in closed, clean rooms where there are no inflammable

liquids or corrosive substances and where it is not too damp.

• Do not place near equipments that generate strong electro-magnetic fields and/or near

equipments that are sensible to electro-magnetic fields. (engines, floppy disks, speakers,

adapters, monitors, video, etc...)

• Do not pour any liquid on the UPS or inside the UPS.

• Do not place the UPS in humid environment or near liquid, such as water, chemical solution…

• Do not expose the UPS to the direct sunlight or any heat sorces.

• Keep the ventilation slits clean to dissipate the heat of the UPS.

• Use grounded power cable to connect the UPS to the mains supply.

• Do not plug laser printers into the UPS because of their high start-up current.

• Do not plug house electric equipments, such as hair dryer,air conditioner, and refrigerator into

the UPS outlets.

2 Conditions of use

Niky 600/800

• Take your UPS out of its packing.

• Make sure the mains supply voltage is identical to the one indicated in the label placed on the

rear of the UPS.

• Switch on your UPS with the ON/OFF button and check it operates correctly with the mains

(green LED on).

• Switch the UPS off by pressing the ON/OFF button until the LED shuts down.

• After switching off the UPS, connect the load power cable to the UPS output using the outlet

located on the right side of the UPS.

• Switch on your UPS and then the load to check it operates correctly with the mains (green LED on).

• Keep the UPS on for 8 hours to recharge battery before using it.

• UPS can also be used before battery is completely charged, but in this case back up time

available during black out will be shorter.

Light signals:

The color of the LEDs on the front panel has the following meanings :

• Fixed green LED: mains present and regular, batteries recharging

• Green LED flashing every 3 sec: running on battery

• Green LED flashing every 0.5 sec: autonomy in reserve

• Green/red LEDs flashing: test or restart after end of autonomy

• Fixed red LED: failure or battery overload

Acoustic signals:

• Intermittent sound every 3 sec: running on battery

• Intermittent sound every 0.5 sec: autonomy in reserve

• Continuous sound: failure, overload or batteries flat

3 Installation

4 Signals and controls

CAUTION

While wiring the outlet line, make sure the total length of the cable, from the UPS to the

farthest utility, does not exceed 10 metres.

NOTICE

Never disconnect the 230 V power plug while the UPS is operating since this would

disconnect the earthing protection both from the UPS and from the loads connected to it.

WARNING

This is a categoryC2UPS product.

In a residential environment, this product may cause radio interference, in which case the

user may be required to take additional measures.

5 Overload and self-shutdown

Your UPS is equipped with a system to measure the power delivered at the outlet; when this exceeds

the set thresholds, the protection and relative signals are activated; shutdown is automatic with a

delay in relation to the size of the overload.

Under the line mode the green led will be light. If the overload is 100% ± 10%; UPS will shutdown

after 5 minutes and go to fault mode. If the overload is 110% ± 10%; UPS will shutdown immediately

and go to fault mode.

Under the battery mode the red led will be flashed.

If the overload is 100% ± 10%; UPS will be shutdown after 5 second and go to fault mode.

If the overload is 110% ± 10%; UPS will shutdown immediately and go to fault mode.

Self test

Automatic self text is executed each time the UPS is switched on, to provide a reliable operation.

Battery Protection

Automatic battery test and deep discharge protection.

DC start capability

The UPS can be switched on in DC mode (battery operation).

UPS power supplied outlets

This is a line interactive UPS equipped with AVR, that allows to feed the load with a stabilized

output voltage even when mains floats.

Electrical protection

Automatic swith off upon short circuit.

CPU microprocessor control

Green function: if battery is discharging under no load, UPS will shut down automatically to save

battery life.

EMI/RFI filtering:

Bad quality of mains supply can damage electronic appliances because of electromagnetic radio

frequency interferences. The UPS is provided with a dedicated filter to eliminat these disturbances.

Full time surge protection outlet

Connect the appliances not needing for back up protection (printers, fax etc.) to the surge

protected outlet located near the back of the unit.

6 Features

Niky 600/800

Software connection Niky 600/800

The UPS is equipped with a USB interface, thanks to which it is possible by means of a computer

to access a set of data regarding the operation of the UPS and control the operating system

unattended shutdown.

Software is available as on option for Win98/ME/2000, Novell and Linux, from the website www.

ups.legrand.com without charge. User license is included in the product.

Telephone protection

The NIKY UPS has an integrated, standard RJ11/RJ45 passing telephone connectionthat provides

protection for telephone or network equipment (modem, telephones, etc.) against overvoltage

6 Features

Caution

Opening, repairing, or replacing parts inside the UPS must always be carried out by specialized

technical personnel only. First of all, switch off the UPS with the ON/OFF button located on the

front panel, then unplug the power cable from the 230V outlet socket.

1) Switch off the uninterruptible power supply.

2) Unplug the power cable from the mains socket.

3) Change the batteries with others of the same type and make, or having the same features

Keep clear from fire to avoid explosion while handling batteries.

Do not open or tamper with the battery case, because it contains toxic electrolyte that could be

harmful for your skin or eyes. Keep out of children’s reach.

7 Changing batteries

NOTICE

The batteries must only be replaced by qualified technical personnel, who will dispose of

them in compliance with the law in force.

8 Possible malfunctioning

The UPS always operates on batteries:

• There is no line voltage

• Line voltage is out of allowed UPS range

• The power supply cable is not correctly connected to mains socket.

• The input circuit breaker has to be reset

• The mains socket is defective

The UPS signals overloading:

• Additional loads to the ones normally connected have involuntarily been connected on the

output line.

• Check all the loads connected to the output

The UPS doesn’t operate in battery mode (it shuts down or immediately signals it is close to the

operating limit):

• The UPS has operated with no mains voltage for a long time and has not been able to recharge

the battery. Recharge it for at least 6 hours by connecting the uninterruptible power supply to

the mains.

• The battery is flat due to not using the UPS for a long period. Recharge it for at least 6 hours by

connecting the uninterruptible power supply to the mains.

• The battery has run down due to being used frequently, to ambient conditions, or to having

exceeded its average service life; it is necessary to change it.

The UPS doesn’t deliver power to the output:

• Check that the loads are correctly connected to the output sockets

Niky 600/800

9 Technical features

CONSTRUCTION SPECIFICATIONS

3 100 02

3 100 09

3 100 22

3 100 03

3 100 10

3 100 23

Weights 7 Kg. 7,5 Kg.

Dimensions L x H x P in mm 95 X 171 X 349

Protection

Electronic protection against overloading

and short-circuiting. Shutdown on

reaching operating limit and overheating.

Automatic shutdown due to protection

triggering

Ambient specifications

Operating temperature range from 0 to +40 °C

Operating relative humidity range from 0 to 95% non-condensing

Degree of protection as per IEC529 IP20

Noise level at 1 meter < 40 dBA

Electrical input specifications

Rated input voltage 230 V

Range of input voltage from 160 V to 290 V

Rated input frequency 50-60 Hz +/-5Hz

Maximum input current 3,75 Arms 5 Arms

Number of input phases Single phase

Waveform on output

With battery operation step wave

Type of operation line interactive

Electrical specifications on output

Rated output voltage 230 V ± 10 %

Output current on nominal load 2,6 Arms 3,48 Arms

Apparent output capacity on nominal load 300 W 400 W

Apparent output capacity on nominal load 600 VA 800 VA

Overload capacity 110% for 5 s.

Number of phases on output Single phase

9 Technical features

CONSTRUCTION SPECIFICATIONS

3 100 02

3 100 09

3 100 22

3 100 03

3 100 10

3 100 23

Electrical specifications on output with battery operation

Rated output voltage 230 V ± 10 %

Output frequency 50/60 Hz ± 1Hz

Active output capacity on non-linear load 300 W 400 W

Apparent output capacity on non-linear load 600 VA 800 VA

Battery operation

Operating time to 80% of the load 5 min. 5 min.

Charging time 10/12 h at the end of operating range

Technical data and number of batteries

n°1

maintenance-free,

sealed, lead-acid

battery

12V 7,2 Ah

n° 1

maintanance-free,

lead-acid,

sealed

12V 9 Ah

Standards

Electromagnetic compatibility

Emission - Immunity Conforms to EN 62040 -2

Safety Conforms to EN 62040 -1

Performance and features Conforms to EN 62040 -3

NOTICE

The batteries are considered hazardous waste and should be disposed of in accordance with

current regulations.

Niky 600/800

1 Status Leds

2 Power Switch

3 Telephone, fax, modem or network protection

4 Output sockets

5 AC Input with AC Fuse

6 USB Serial Interface

9 Technical features

SITE WIRING FAULT

AC INPUTAC OUTPUT

IN OUT

112

3 100 09

3 100 10

3 100 02

3 100 03

3 100 22

3 100 23

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Fuente de alimentación de LEGRAND

LEGRAND

LEGRAND 0 634 42 Manual de usuario

LEGRAND

LEGRAND E49 Manual de usuario

LEGRAND

LEGRAND 0 883 34 Manual de usuario

LEGRAND

LEGRAND 4130 17 Manual de usuario

LEGRAND

LEGRAND UPS Manual de usuario

LEGRAND

LEGRAND DPX3 250 Manual de usuario

LEGRAND

LEGRAND 634 42 Manual de usuario

LEGRAND

LEGRAND 4 130 17 Manual de usuario

LEGRAND

LEGRAND KEOR HPE UPS 200 KVA Manual de instalación y operación

LEGRAND

LEGRAND 4 130 17 Manual de usuario

LEGRAND

LEGRAND Trimod MCS Series Manual de usuario

LEGRAND

LEGRAND KEOR PDU Manual de usuario

LEGRAND

LEGRAND 035 65 Manual de usuario

LEGRAND

LEGRAND KEOR MOD Manual de usuario

LEGRAND

LEGRAND 4 142 03 Manual de usuario

LEGRAND

LEGRAND KEOR T EVO Manual de usuario

LEGRAND

LEGRAND KEOR HPE UPS Manual de instalación y operación

LEGRAND

LEGRAND WIREMOLD 1022306R2 0119 Manual de usuario

LEGRAND

LEGRAND E47ADCN Manual de usuario

Manuales populares de Fuente de alimentación de otras marcas

Monacor

Monacor PS-12CCD Manual de usuario

VOLTIMA

VOLTIMA MagicBox 15 Manual de usuario

Agilent Technologies

Agilent Technologies 6032A Manual de usuario

Miller

Miller Auto Deltaweld 452 Manual de usuario

BCP

BCP PUOUBK Hoja de instrucciones

HC 2210 Manual de usuario

Puls

Puls CT5.241 Manual de usuario

OCZ

OCZ ZX1250W Manual de usuario

iseg

iseg ECH 238 Manual de usuario

Power

Power XXL A Series Manual de usuario

Agilent Technologies

Agilent Technologies 6631B Manual de usuario

Renogy

Renogy PHOENIX 300 Manual de usuario

HP 6200B Manual de servicio

Epson

Epson Stylus Scan 2500 Manual de funcionamiento

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manual de usuario

Puls

Puls MiniLine ML50.100 Manual de usuario

Puls

Puls AS-Interface SLA4.100 Manual de usuario

Kenwood

Kenwood PS-60 Manual de usuario