Legend LSD2 Manual de usuario
USER MANUAL
LSD2 – LEGEND STANDARD DEFINITION SET TOP BOX
www.legenddigital.com
www.legenddigital.com
v1.2
CONTENTS
Safety Instruction 3
PackingList 4
Front Panel 5
Rear Panel 5
RemoteController 6
InstallationGuide 7-11
EPG 12
Feature 12
Specification 13
2
SAFETY INSTRUCTIONS
Please read the following instruction carefully:
Do not overload power outlets, extension cords or integral convenience receptacles as this can
result in a risk of fire or electrical shock
Never allow liquids, spray or other materials to come into contact with the inside of the Set Top
Box (STB).
Unplug the STB from the power outlet before cleaning.
Use a soft cloth and a mild solution of washing-up liquid to clean the exterior of the STB.
Allow a clear space around the STB for sufficient ventilation.
Do not use the STB where it is exposed to direct sunlight or heat.
Never stack other electronic equipment on top of the STB.
Locate the STB in an indoor place to prevent exposing from lightening, rain and direct sunlight.
Do not use any attachments as these may cause hazards or damage the equipment.
Do not connect or modify the power cable attached to the STB.
Do not cover or place the STB on a unit that emits heat.
This symbol indicates
“dangerous voltage” inside
the product that present a
risk of electric shock or
personal injury.
This symbol indicates
important instructions
accompanying the
product.
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
3
PACKING LIST
ITEMS Qty. REMARK
DIGITAL TERRESTRIAL RECEIVER 1
INSTRUCTION MANUAL 1
REMOTE CONTROL 1 Batteries inc
AV CABLE 1
NOTE:Any changes will not be noticed in advance. Our company reserves the rights for the
explanation of the discrepancy.
4
FRONT PANEL
1 7 86
3
5 10 9
2 4
1. Card slot (NOT USED FOR AUSTRALIA) 6. Standby switch
2. EXIT: return to the program-watching status 7. Volume decrease/ left button
3. MENU: Menu entry 8. Channel increase/ up button
4. OK: menu confirmation/ channel list 9. Volume increase/ right button
5. Remote receiver LED display window 10. Channel decrease/ down button
REAR PANEL
1
32 4 5 6
1. Power switch 5. Video signal output terminal
2. Loop output terminal 6. Audio signal output terminal
3. Antenna signal input terminal
4. Serial data interface – only use for software upgrades
5
REMOTE CONTROLLER KEYS
Advise you operate each function of the STB using the button on the remote controller. Please
read this section to help advance your understanding of the function of the STB.
1. : Standby control
2. : mute the audio output
3. FAV : Non-Menu Mode: Select FAV list
4. TEXT : Non-Menu Mode: TEXT Teletext
5-6. ▲/▼:
Menu Mode : Move cursor up/down
Non-Menu Mode: Program serial increase / decrease
7-8. -/+:
Menu Mode: Left or right button
Non-Menu mode: Volume decrease / increase
9. EXIT: Exit / Go back
10. MENU: Invoke or exit the menu operation
11. Numeric buttons 0-9: Input digits
12. SUB: Subtitles
13. TV/ RAD: Switch between TV and Radio
14. PAUSE: Non-Menu mode: Pause Picture
15. INFO: program’s Information
16. RECALL: Recall last channel
17. EPG: Electronic Program Guide
18. MULTI-FUNCTION Buttons: red (audio language)
green, yellow, blue (Electronic Program Guide)
19. OK: Non- Menu Mode: Channel List Menu Mode
Mode: Confirmation
PRECAUTIONS ABOUT BATTERIES
Improper use of batteries may cause corrosion or fluid leakage. Please observe the following
instructions for the safe use of batteries
1. Do not mix up the polarities of batteries
2. Never leave dead batteries in the remote control
3. Remove batteries from the remote controller if it is not going to be used for a certain time
4. Do not attempt to disassemble, short-circuit, heat, recharge or throw the batteries into a
fire.
5. Do not use new & old batteries together, or different types of batteries.
6. Wipe away any electrolyte fluid inside the remote controller, and insert new batteries
6
LEGEND INSTALLATION GUIDE:
LSD2 – LEGEND STANDARD DEFINITION SET TOP BOX
This document will guide you step by step on how to connect and set up your LSD2 set top box.
Users with experience in entertainment systems setup may not require this document as it is
intended for those with little or no prior knowledge on these units.
1) Place the unit in a suitable location near your TV. The unit should not be placed directly
on or under another electrical device (as this may cause interference) and should have
some room at the sides and top to allow the unit to remain cool.
2) Plug the unit’s power cord into your wall socket and turn on at the wall. On the back of
the unit, press IN the round POWER button.
Power is OFF Power is ON
3) You should now see green lights on the front display of the unit (if you only have 1 green
LED but no information is displayed on the front LCD, your unit is in standby. Press the
power button on the FRONT and you will see the LCD activate and show green indicator
bars). If all is well you should see this:
7
4) You now must connect your aerial. You may have an inside aerial (rabbit ear type) or a
roof antenna with a wall plug. Using an appropriate cable, connect the aerial to the RF IN
connection on the rear of the unit (top middle) as below:
5) Now you must connect the AV cables (the red, white, and yellow cables that came with
your unit) to the rear of the unit. The cables are colour coded; simply connect them with
the colours matching.
8
Diagram above shows all connections in place for LSD2.
Read on for further instruction.
6) The other end of the AV cables will need to then be connected, in the same way, to the
AV-INPUT connectors on either your VCR or your TV. In order to record from your digital
box to videocassette, you will need to connect the unit direct to the VCR (set VCR to
appropriate AV channel as indicated on the connection you use, eg AV1, AV2…) and
then connect the VCR to the TV as per normal. Otherwise, connect the unit direct to the
TV (in this case, set the TV to appropriate AV channel as indicated on the connection
you use, eg AV1, AV2…).
7) If you have made the connections correctly, everything is turned on, and you are set to
the correct AV channels, you will now see this image on your TV screen:
9
8) Now you must SCAN in your channels. Make sure the batteries (supplied) are installed in
your REMOTE CONTROL unit. Point the remote at the digital box and press MENU.
Then use the up and down buttons on the remote to highlight SCAN at the bottom of the
menu, and press OK. You should see the following:
9) After checking that the SCAN TYPE is set on AUTO, and the BAND WIDTH is set to
7MHz (leave the Channel Number field BLANK), use the down button to highlight START
SCAN and then press OK. You will see the unit picking up channels as it scans, like this:
10
Tabla de contenidos
