Leenders WALD Manual de usuario
WALD
INSTALLATION EN
WALD LEENDERS
2019.49.002.I.EN
4
4
Installaon opon 1; xing THROUGH ceiling. Installaon opon 2; xing TO ceiling.
WALD LEENDERS
2019.49.002.I.EN
Points for special aenon when installing the Wald
• Installaon opon 1, xing with threaded ends and counter plate is recommended. This provides
the Wald with beer side-collision protecon.
• If the ceiling height exeeds 2750mm, the Wald can only be suspended according to opon 1, with
the counter plate and threaded ends.
• The Wald can only be connected to an insulated double-walled ue.
• This stove appliance must be ed to a ceiling that can easily support the load.
• The weight of the double-walled ue must not be supported by the connecon to the Wald.
Poujoulat Ecience
• Can be connected to the Poujoulat Ecience to draw in fresh air through the ue. A special
connector is required for this and can be supplied with the stove if requested.
Art. nr. ENA15SP49.
• The Poujoulat Ecience duct may be up to 6 metres in length.
WALD LEENDERS
2019.49.002.I.EN
Installaon opon 1; xing THROUGH ceiling.
Fixing with threaded ends and counter plate is recommended.
This provides the Wald with beer side-collision protecon.
1. Posion the counter plate on the ceiling.
3. Secure the ceiling plate to the
threaded ends with 4x coupling
nuts and M8x20 countersunkhead
bolts.
2. Fix the threaded ends tot the counter
plate.
4. Fix both plates with the nuts on
the counterplate.
WALD LEENDERS
2019.49.002.I.EN
Installaon opon 2; xing TO ceiling.
.
1. Mark out het ceiling plate
Use the cardboard template. Face
the atbit to the rear. Mark the 12
holes on the ceiling.
2. Drill holes
Drill 6 holes distributed over the
ceiling plate. Pilot drill with
Ø
6, nish
with
Ø
14.
Should a posion be dicult to drill
through, use one of the other
marked posions.
3. Securing ceiling plate
Use 6 anchors and M8x55
countersunk head bolts. The bolts
must not protrude form the ceiling
plate.
Please note: the construcon of the ceiling must be appropriate for this
method of aachment.
WALD LEENDERS
2019.49.002.I.EN
Installaon opon 1&2
4. Determine the length of the double-walled inner ue
Use a telescopic, double-walled ue that can be adjusted to t
- L= Length telescopic double-walled ue, excluding the connector
- X = Length mantel pipe Wald
- Y = Length of double-walled ue that protrudes from the ceiling
- L = X - Y - 65mm
5a. Double-walled connector
Install the connector for the double-walled ue
5b. Poujoulat connector (only for use with the Poujoulat Ecience)
Install the connector for the Poujoulat Ecience ue
6. Perparing the mantel pipe
Lay the mantel pipe horizontally. Insert the double-walled ue adjusted to length into the mantel pipe.
Bring the mantel pipe with the double-walled ue inot an upright posion.
WALD LEENDERS
2019.49.002.I.EN
7. Installing the double-walled ue
Li the double-walled ue out of the mantel pipe
and aach this to the secon that is protruding
from the ceiling.
8. Aaching the mantel pipe
Put the mantel pipe on the li. Use the li for
aaching the mantel pipe to the ceiling plate.
Secure the mantel pipe with 6x M8x16
countersunk head bolts.
WALD LEENDERS
2019.49.002.I.EN
9. Levelling the mantel pipe
Check to see if the mantel pipe is haning plumb. Adjust for plumb if necessary using the 3x socket-head
screws. Loosen the 6x M8x16 a lile befor you do this. Aerwards re-ghten the 6x M8x16.
10. Transport the stove with a hand truck
Use protecon between the stove and the hand truck.
Ensure that the wooden transport plate is snug against the
base. Seat the stove with the side against the hand truck.
Never posion the stove with the front against the hand
truck; this can damage the glass.
Never posion the stove with the back against the hand
truck; this can damage the air valve.
11. Swivel lock
If 2x60
°
rotatable, install the swivel lock.
WALD LEENDERS
2019.49.002.I.EN
12. Posion stove on the li
13. Aaching the connector
Elevate the li and rst aach the double-walled ue to the
swivelling ring. Please note: the weight of the double-walled ue
must not be supported by the Wald’s swivelling connector.
14. Securing the stove
Elevate the li more and secure the stove. Use the 6x M8 bolts supplied.
WALD LEENDERS
2019.49.002.I.EN
15. Transport plate
Remove the M6 bolt and with this the wooden
transport plate.
16. Air supply cover plate (only for use with the
Poujoulat Ecience)
Secure the air supply cover plate underneath with
3x M6. Please note: only install the cover plate in
conjuncon with the Poujoulat Ecience.
17. Foot
Secure the foot with M6 threaded end and nut.
Tabla de contenidos
Otros manuales de Chimenea de interior de Leenders
