LCN Benchmark III 9130 Manual de usuario
Installation Instructions 740158-00
Benchmark®III
Swing Operator
Models: 9130, 9140, & 9150
121 West Railroad Avenue
Princeton, IL 61356-0100
800-526-2400
FAX: 800-248-1460
www.lcn.ingersollrand.com
740158-00
(
1
)
©
2008 In
g
ersoll-Rand Com
p
an
y
Limited
Page 2 of 19
General 2
Replacement Parts and System Components 2
1. Pre-Installation Site and Product Check 4
2. Operator Installation 5
3. Wiring 9
4. Arm and Cover Installation 10
5. Operational Check 12
6. Operator Adjustment 15
7. Release for Service 17
8. BenchMark III Software 18
GENERAL
The Benchmark is an automatic electromechanical swinging door operator for use on hinged,
center pivoted and offset pivoted doors. When activated, the Benchmark drives the door to full
open position, then electrical power is turned off and the door is closed by spring force. The
activating circuit opens the door from any position in the closing swing. During a power failure,
the Benchmark acts as a manual door closer (Size 3). Door opening and closing cycles,
including opening speed, back check speed, hold open time delay, closing speed, and latch
position, are adjustable.
Part 27” Header Full Length Header
Single Full Length Header
Double
Premium Control
Box 9130-3462SC
9140-3462SC 9130-3462SC
9140-3462SC 9150-3462SC
Gear Box 9130-3454S
9140-3554S 9130-3454
9140-3454 9150-3454S
End Caps 9130-334 9140-334 9150-334
Part Pull Standard Push Extended
Reveal Push Finish
Arm Assembly 9130-3077T 9140-3077
9150-3077 9140-3077L
9150-3077L US28
DC13
CONTENTS
REPLACEMENT PARTS & SYSTEM COMPONENTS
Page 3 of 19
REPLACEMENT PARTS & SYSTEM COMPONENTS (CNTD)
Page 4 of 19
1.1 Check that the Product Model is correct for the required application.
1.2 Check that all parts listed on the Bill of Material are in the shipping container.
1.3 Check the architectural drawings and final approved shop drawings for the position
of frame and structural openings.
1.4 Check header and frame dimensions and required clearances.
1.5 Check Door Width: 26” minimum for 27” Push Operator
30” minimum for 27” Pull Operator
36” minimum for Full Length Push or Full Length Pull Operators
1.6 Check that Door Weight is 200 lbs. or less. For heavier door, consult factory.
1.7 Check that a 115 volt, single phase, 60 Hz, fused 15 amp, 3-wire power supply is available
at the side jamb with approximately 12” of wire available to connect to the Operator.
UL approved flexible conduit is recommended for the 115 volt power line.
The 115 volt power supply must be a dedicated circuit from the main circuit breaker panel
and must NOT be connected into any building lighting system that operates flourescent
lights.
1. PRE-INSTALLATION SITE & PRODUCT CHECK
Page 5 of 19
2.1 Remove Control Box from Operator Mounting Bracket, then remove Motor/Gearbox from
Bracket:
2.2 Prepare Header/Frame and Door: 27” Pull System..............................Page 6
Full Length Pull System..................Page 6
27” Push System............................Page 7
Full Length Push System ...............Page 7
Double Push System......................Page 8
Low Ceiling Application..................Page 8
2.3 Install Operator Mounting Bracket on Header/Frame.
For Full Length systems, also install Switch Bracket on Header/Frame.
2.4 Install Motor/Gearbox on Operator Mounting Bracket.
Then install Control Box on Bracket.
2.5 Proceed to Chapter 3: Wiring (Page 9).
2. OPERATOR INSTALLATION
Page 6 of 19
27” Pull System
Header/Frame and Door Preparation
Full Length Pull System
Header/Frame and Door Preparation
Center Operator Cover (with End Caps removed) over opening and mark a vertical line at each
end. Align ends of Operator Mounting Bracket and Switch Bracket with vertical lines and adjust
vertical position per diagram below. Mark and prepare mounting holes.
2. OPERATOR INSTALLATION (CNTD)
Page 7 of 19
27” Push System
Header/Frame and Door Preparation
Full Length Push System
Header/Frame and Door Preparation
Center Operator Cover (with End Caps removed) over opening and mark a vertical line at each
end. Align ends of Operator Mounting Bracket and Switch Bracket with vertical lines and adjust
vertical position per diagram below. Mark and prepare mounting holes.
2. OPERATOR INSTALLATION (CNTD)
Page 8 of 19
Double Push System
Header/Frame and Door Preparation
Center Operator Cover (with End Caps removed) over opening and mark a vertical line at each
end. Align ends of Operator Mounting Bracket and Switch Bracket with vertical lines and adjust
vertical position per diagram below. Mark and prepare mounting holes.
Low Ceiling Application (27” Push System Only)
Header/Frame and Door Preparation
2. OPERATOR INSTALLATION (CNTD)
Page 9 of 19
TION
3.1 Refer to the appropriate wiring diagram for the Control Box (Page 19) or the diagram
supplied for custom applications.
Connect the following cables:
•Ground Cable (Ground the Operator properly with the earth from main supply)
•Hall Effect Cable (Do not wrap the Hall Effect Cable around the Motor Power Cable)
•Motor Power Cable (Do not wrap the Motor Power Cable around the Hall Effect Cable)
•Control Box Power Cable
3.2 Connect Activate, Safety, Key Switch, and lock accessories, as needed.
Refer to the accessory instructions for any accessories used.
Do not connect any remote activating device to the door unless it is located within
line of sight of the door.
3.3 When wiring is complete, proceed to Chapter 4: Arm and Cover Installation (Page 10)
3. WIRING
CAUTION
• Make sure all wires are properly dressed and secured to prevent interference
• Route all wiring away from moving parts, sharp edges, and heat sources
• Use copper conductors only
• Do not modify the factory wiring or connect into existing electrical circuits or devices
Page 10 of 19
WARNING
Keep hands, clothing, wires, tools, etc., AWAY FROM Operator Motor
when the Operator Motor is turned on
4.1 Make sure the Operator Powers is turned Off.
4.2 Install a jumper across the control box Main Act and Main Act.
4.3 Turn the operator power switch to On.
The operator motor will activate and drive to the Full Open position.
4.4 Attach the arm to the operator spindle loosely with the 8mm socket head screw.
For push systems, ensure that the adjusting boss is inserted correctly.
4.5 Attach the arm to the door.
4.5.1 For push systems, attach the push arm shoe to the door:
4. ARM & COVER INSTALLATION
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Sistema de apertura de puertas de LCN
LCN
LCN 4310ME Series Manual de usuario
LCN
LCN 3030 Series Manual de usuario
LCN
LCN 2210DPS Series Manual de usuario
LCN
LCN 4412 HSA Manual de operación y mantenimiento
LCN
LCN 1461 CUSH Manual de usuario
LCN
LCN 8310-2420 Manual de usuario
LCN
LCN 4031 CUSH Manual de usuario
LCN
LCN 4050 Track Series Manual de usuario
LCN
LCN 4050 Series Manual de usuario
LCN
LCN 4630CS Manual de usuario
LCN
LCN 1450 Track Series Manual de usuario
LCN
LCN 4020 Series Manual de usuario
LCN
LCN 1261 CUSH Manual de usuario
LCN
LCN 4050AT Manual de usuario
LCN
LCN 2010 SERIES Manual de usuario
LCN
LCN 4050 Series Manual de usuario
LCN
LCN 4040SE Manual de usuario
LCN
LCN 4110EDA Manual de usuario
LCN
LCN 8310-2410 Manual de usuario
LCN
LCN Sentronic 2310-ME Manual de usuario
