LCG MOLEFAY 4A Manual de usuario

MOLEFAY 4A

WARM COOL WHITE

LED BLINDER

USER MANUAL

INTRODUCTION

Thank you for having chosen our LED lighting.

Unpack the device, inside the box you should find:

The fixture device;

One power cable;

One XLR connection cable;

This manual.

Please check carefully that there is no damage caused by

transportation. Should there be any problems, consult your dealer

and don’t install this device.

DESCRIPTION

Features:

Easy multi fixture hanging system, outdoor version available;

4 x 100W 3000k LEDs, noultraviolet radiation;

Over 50,000 hours life of the LED light source;

16,466 lm;

1300 lux @5meters;

60 degrees beam angle;

1/3/4/9/10 DMX channels;

16 Bit dimmer;

DMX mode/ master-slave mode;

AC 100-240V 50/60Hz 400W;

Diecasting heatsink, convection cooling with silent fans;

Includes temperature sensor to extend the lamp life;

LED scan rate:1,000/ 5,000/ 10,000/ 50,000Hz;

L: 373mm H: 373mm W:193mm, weight 9Kg;

IP65.

SAFETY INSTRUCTIONS

This device has left the factory in perfect condition. In order to

maintain this condition and to ensure a safe operation, it

is absolutely necessary for the user to follow the safety

instructions and warning notes written in this user manual.

This device falls under protection-class I. Therefore it is essential that

the device should be earthed.

The electric connection must carry out by qualified person.

If the external flexible cable or cord of this luminaire is damaged,

it shall be exclusively replaced by the manufactu r e r, his

service agent or a similar qualified person in order to avoid a hazard.

Make sure that the available voltage is not higher than stated at the

end of this manual.

Make sure the power cord is never crimped or damaged by sharp

edges.

If this would be the case, replacement of the cable must be done by

an authorized dealer.

Always disconnect from the mains, when the device is not in use or

before cleaning. Only handle the power cord by the plug. Never

pull out the plug by tugging the power cord.

Never look directly into the light source, as

sensitive persons may suffer an epileptic shock.

Important:

Damages caused by the disregard of this user manual are not

subject to warranty. The dealer will not accept liability for any

resulting defects or problems.

DMX-512 control connection

The product has a DMX 512 input fitted with 3-pin XLR connectors.

Screened cables in compliance with EIA RS-485 specifications and the

following characteristics must be used for connections:

-2 conductors plus screen;

-120 Ohm impedance;

-low capacitance;

-max. transmission rate 250 kBaud.

DMX-512 connection with DMX terminator

For installations where the DMX cable is required to run a long

distance or at an electrically noisy environment, such as inside a

discotheque, it is recommended to use a DMX terminator. This helps

on preventing the corruption of the digital control signal by electrical

noise. The DMX terminator is simply an XLR plug with a 120 OHM

resistor connected between pins 2 and 3,which is then plugged into the

output XLR socket of the last fixture in the chain.

Display Menu

Main menu Sub-menu Values Defaut

Address DMX address setting 1 - 512 1

Config. mode

Channel mode

Channel 1Ch

Channel

13Ch

Channel 3Ch

Channel 8Ch

Channel 13Ch

Channel 14Ch

Keep screen on Disable Disable

Enable

Keep DMX data Disable Disable

Enable

Fast dimmer Enable Enable

Disable

System Info Temperature

Head 1 -

Head 2 -

Head 3 -

Head 4 -

Body -

LED all on - - -

Auto test

Auto mode 1 - -

Auto mode 2 - -

Auto mode 3 - -

LED test

LED white 1 0 - 255 0

LED white 2 0 - 255 0

LED white 3 0 - 255 0

LED white 4 0 - 255 0

FScan rate

Strobe

Main functions

1. Address: current DMX address

A. Setting DMX address by button

press [ENTER] button when show the address menu, then

adjust the DMX address by pressing [UP] or [DOWN] button

Press [ENTER] to confirm or pressing [ESC] to return to main

menu.

B. Setting DMX address by controller

1. Set the DMX value of channels 5 to 10-15, channels 17 to

20-26, channels 7 to 30-36, channels 8 to 40-46, then the devices

connected to the controller will enter to the setting address mode.

2. Set the DMX value of channel 1 from 0-59, then you will see

the first number of the Address change to (channel 1 value)/10.

For example, when set the value of channel 1 to 20, the first

DMX address number will be 2 (20/10=2).

3. Set the DMX value of channel 2 from 0-99, then you will see

the second number of the Address change to (channel 2

value)/10.

For example, when set the value of channel 2 to 30, the first

DMX address number will be 3 (30/10=3).

4. Set the DMX value of channel 3 from 0-99, then you will see

the third number of the Address change to (channel 3 value)/10.

For example, when set the value of channel 1 to 40, the first

DMX address number will be 4 (40/10=4).

And the DMX address set by the controller will be 234.

5.Set the DMX value of channel 4 to 255, then you will save the

DMX address settled by the controller.

Caution: It won’t save the address if the address number

is over 512.

6. set the value of channel 5-8 out of the value range shown on

the step 1, and the device will exit the setting address mode.

2. config.

Setting DMX mode

press [ENTER] button when shown the channel menu, then

select the DMX mode by pressing [UP] and [DOWN] buttons.

Keep screen on

press [ENTER] button when shown the keep screen on in the

sub-menu and by pressing [UP] and [DOWN] buttons, enabling or

disabling the function LEDs all on.

Keep DMX data

press [ENTER] button when shown the keep DMX data in the

sub-menu and by pressing [UP] and [DOWN] buttons, enabling or

disabling the function LEDs all on.

Fast mode

press [ENTER] button when shown the fast mode menu, then

select able or disable by pressing [UP] and [DOWN] buttons.

3. System info

Temperature

press [ENTER] button when shown the temperature menu,

then it will show the temperature of the fixture.

4. Auto test

press [ENTER] button when shown the Auto test menu, press

[UP] and [DOWN] button to select the auto mode.

5. Led test

press [ENTER] button when shown the Led test menu, press

[UP], [DOWN] and [ENTER] buttons to select the LED.

DMX functions and values

1CH Mode

No.

Function

Value

Description

Remark

Dimmer

000-255

0-100%

3CH Mode

No.

Function

Value

Description

Remark

Master dimmer

000-255

0-100%

Fine master dimmer

000-255

0-100%

3 Strobe

000-015

No function

016-255

Strobe

Slow to fast

4CH Mode

No.

Function

Value

Description

Remark

Head 1

000-255

0-100%

2Head 2

000-255

0-100%

3head 3

000-255

0-100%

4head 4

000-255

0-100%

9CH Mode

No.

Function

Value

Description

Remark

Master dimmer

000-255

0-100%

Fine master dimmer

000-255

0-100%

3 Strobe

000-015

No function

016-255

Strobe

Slow to fast

White 1

000-255

0-100%

White 2

000-255

0-100%

White 3

000-255

0-100%

White 4

000-255

0-100%

8Auto Mode

000-035

No function

036-071

Round up

072-107

Round

down

108-143

Round up

down

144-179

SIN up

180-215 4-LEDs

standard -

216-255 4-LEDs

random

9Dimmer mode

000-063

Linear

064-127

Square

128-191

Inverted

square

191-255

S-curve

10CH Mode

No.

Function

Value

Description

Remark

Master dimmer

000-255

0-100%

Fine master dimmer

000-255

0-100%

3 Strobe

000-015

No function

016-255

Strobe

Slow to fast

White 1

000-255

0-100%

White 2

000-255

0-100%

White 3

000-255

0-100%

White 4

000-255

0-100%

8Auto Mode

000-035

No function

036-071

Round up

072-107

Round

down

108-143 Round up

down -

144-179

SIN up

180-215 4-LEDs

standard

216-255

4-LEDs

random

9Dimmer mode

000-063

Linear

064-127

Square

128-191

Inverted

square

191-255

S-curve

10 Dimmer speed

000-254

tungsten

effect

Fast to slow

255

Tungsten

effect

CLEANING AND MAINTENANCE

We recommend a frequent cleaning of the device. Please use a soft

lint-free and moistened cloth. Never use alcohol or solvents!

CAUTION! Disconnect from mains before starting

maintenance operation.

Maintenance and service operations are only to be carried out by

authorized dealers. If you need any spare parts, please use

genuine parts. If the power supply cable of this device becomes

damaged, it has to be replaced by authorized dealers only in

order to avoid hazards. If you have further questions, please

contact your dealer.

INSTALLATION

The device must only be installed at a vibration-free,

oscillation-free and fire-resistant location.

Tabla de contenidos

Otros manuales de Equipo de iluminación de LCG

LCG

LCG Thunder 400 Manual de usuario

LCG

LCG LEAD PACK 14 Manual de usuario

LCG

LCG LCG-079 Manual de usuario

LCG

LCG BEAMER 44 Manual de usuario

LCG

LCG PARBAR QUAD Manual de usuario

LCG

LCG LCG-PL64Z Manual de usuario

LCG

LCG PRO LCG-FS400L Manual de usuario

LCG

LCG LCG-027A Manual de usuario

LCG

LCG ST-04 Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario