LAUNCH TECH Millennium 40 Manual de usuario

Note: To make sure the tool is running the latest available software,

it is advisable to check for updates on a frequent basis. Refer to

Section 3 “Register & Update” for details.

1. Preparation

Turn the vehicle ignition on.

Vehicle battery voltage range should be 9-14Volts.

Throttle should be in a closed position.

2. Vehicle Connection

1. Locate vehicle's DLC socket: The DLC (Diagnostic Link

Connector) is typically a standard 16-pin connector where

diagnostic code readers interface with a vehicle's on-board

computer. It is usually located 12 inches from the center of

the steering wheel, under or around the driver's side for

most vehicles.

If the DLC cannot be found, refer to the vehicle's service

manual for the location.

2. Connect the diagnostic cable into the vehicle's DLC

socket.

1. Preparation & Connections

DTC

F1 F2 F3 F4

I/ M

DLC Location

Diagnostic Cable

LCD Screen

OK Button

USB Port

(To update your tool via USB cable.)

Millennium 40/50/60 Handset

Selection Button

ESC Button

(To return to the previous screen.)

DTC Button*

Erase Button*

I/M Button*

Help Button*

(To read the diagnostic

trouble codes.)

(To clear the diagnostic

trouble codes.)

(Quick access to I/M

readiness function.)

(Provides online tips

for diagnostics.)

Note: Millennium 40

features the same

styling as Millennium

50/60, except for the

LCD screen size. The

pictures shown here are

only for reference.

Note:

The buttons marked with * indicate the function hot keys(namely,

F1, F2, F3 and F4) and only apply to Diagnostics.

This Quick Start Guide is subject to change without written notice.

Quick Start Guide

40 50/60/

1~ 4/10

I/M Readiness

Misfire Monitor

Fuel system

component monitor

Catalyst monitor

N/A

INC

N/A

DTC

C138F 1/13

GM Pending

The fault code is not found in the database

Monitor Status

MIL Status

DTCs in this ECU

Readiness Completed

Readiness Not Completed

Readiness Not Supported

Datastream Supported

Ignition

Protocol Type

OFF

108

119

Spark

CAN

Product Serial Number

Device Upgrade

Select Language English

3. Register & Update

2. Basic Operations

The tool can be updated via USB cable.

Note: Make sure the PC has an Internet connection.

1. Go to and download the update tool to the

computer.

2. Decompress and install it on your computer(compatible with

Windows XP, Windows 7, Windows 8 & Windows 10).

3. After installation, connect one end of the USB cable to the

USB port of PC, and the other end to the tool.

4. If a newer version is found, a

screen similar to Fig. A will

appear.

5. Launch the update tool on

your PC, Fig. B will appear.

6. Choose the desired interface

language and then click [Device

Update] to enter update center.

7. Choose the software version and then click [Update] to start

updating.

8. Once update is complete, a “Upgrade success” message

box will pop up.

9. The update process is complete, your tool is now ready for

use.

www.dbscar.com

Boot Version:

V1.00.000

Serial Number:

972890000029

36FFDB054753

1. USB Connected for Upgrade.

2. Press [EXIT] key to Enter

Normal Mode.

The icons in black at the bottom of

the screen indicate the available

actions, which can be done by

pressing the corresponding buttons

on the tool.

Press the F3/I/M button to check the

I/M(Inspection & Maintenance)

readiness.

Press the F1/DTC button to retrieve

the DTC.

Press the F4/ button to get more

details about the DTC.

If more than one DTC was retrieved,

press / to view different DTCs.

In the case of long code definitions,

use / to view the additional

information.

Read DTC

Erase DTCs

Check I/M Readiness

Once DTCs have been retrieved,

press the F2/ER button to erase.

Erase Codes

Clear/Reset Emission-Related Diagnostic

Information. Are you sure?

Quick Start Guide

40 50/60/

Este manual sirve para los siguientes modelos

Otros manuales de Equipo de diagnóstico de LAUNCH TECH

LAUNCH TECH

LAUNCH TECH X-431 PRO5 Manual de usuario

LAUNCH TECH

LAUNCH TECH X-431 PRO MINI Manual de usuario

LAUNCH TECH

LAUNCH TECH EasyDiag Manual de usuario

LAUNCH TECH

LAUNCH TECH X-431 EuroPro5 Manual de usuario

LAUNCH TECH

LAUNCH TECH X-PROG Manual de usuario

LAUNCH TECH

LAUNCH TECH X-431 PRO5 Manual de usuario

LAUNCH TECH

LAUNCH TECH X-431 HTT Manual de usuario

LAUNCH TECH

LAUNCH TECH CRT511 Manual de usuario

LAUNCH TECH

LAUNCH TECH X-431 Torque 5 Manual de usuario

LAUNCH TECH

LAUNCH TECH CRP 429HD Manual de usuario

LAUNCH TECH

LAUNCH TECH X-631 Manual de usuario

LAUNCH TECH

LAUNCH TECH X-431 PAD V Manual de usuario

LAUNCH TECH

LAUNCH TECH Creader 629 Manual de usuario

LAUNCH TECH

LAUNCH TECH Premium CRP 12 Series Manual de usuario

LAUNCH TECH

LAUNCH TECH X-431 PRO3 SE Manual de usuario

LAUNCH TECH

LAUNCH TECH EasyDiag4 Manual de usuario

LAUNCH TECH

LAUNCH TECH X-431 Torque Auto HD Manual de usuario

LAUNCH TECH

LAUNCH TECH X-431 PRO3 Manual de usuario

LAUNCH TECH

LAUNCH TECH CreaderVII Manual de usuario

LAUNCH TECH

LAUNCH TECH X-431 Diagun III Manual de usuario

Manuales populares de Equipo de diagnóstico de otras marcas

Mindray

Mindray M7Vet Guía de inicio rápido

Autel

Autel MaxiProgrammer 201 Manual de usuario

TEXA

TEXA TMD2 Manual de usuario

Autel

Autel MaxiIM IM608 Manual de usuario

Sealey

Sealey BT2012 Manual de usuario

Diagnoptics

Diagnoptics Age Reader Manual de usuario

Hella Gutmann

Hella Gutmann Mega macs X Manual de usuario

Foxwell

Foxwell I80TS Manual de usuario

KaVo

KaVo 3D eXam Manual de usuario

ATEQ

ATEQ VT46 Manual de usuario

Hella Gutmann

Hella Gutmann mega macs X Manual de usuario

Autel

Autel MaxiFlash VCMI Manual de usuario

Qiagen

Qiagen QIAcube Connect MDx Manual de usuario

Alber

Alber BDSU Manual de usuario

St. Jude Medical

St. Jude Medical QUANTIEN Manual de usuario

Bosch

Bosch DCU 100 Manual de usuario

Launch

Launch CNC-602A Manual de usuario

Innova

Innova 3568 Manual de usuario