Laserworld Evolution ES-180S RGY 3D Manual de usuario

Manual / Bedienungsanleitung

Evolution Series

ES-180S RGY 3D

Please read this manual carefully prior to product operation!

Bitte lesen Sie diese Bedienungsanleitung vor Inbetriebnahme des Produkts!

03/2014

English

Deutsch

Manual: Evolution Series ES-180S RGY 3D

page 2 / 22

Rechtlicher Hinweis:

Die Firma Laserworld (Switzerland) AG behält

sich das Recht vor, Änderungen an ihren Pro-

dukten vorzunehmen, die der technischen

Weiterentwicklung dienen. Diese Änderun-

gen werden nicht notwendigerweise in je-

dem Einzelfall dokumentiert.

Diese Betriebsanleitung und die darin ent-

haltenen Informationen wurden mit der ge-

botenen Sorgfalt zusammengestellt. Die Fir-

ma Laserworld AG übernimmt jedoch keine

Gewähr für Druckfehler, andere Fehler oder

daraus entstehende Schäden.

Die in dieser Bedienungsanleitung genann-

ten Marken und Produktnamen sind Waren-

zeichen oder eingetrageneWarenzeichen der

jeweiligen Titelhalter.

Legal notice:

Laserworld AG reserves the right to make

modications to its products, attending to

further technical developments. These modi-

cations do not necessarily have to be recor-

ded in each case.

This manual and its information have been

made with due care. Laserworld AG cannot,

however, take any responsibility for errata,

bugs, or the resulting damages.

The brands and product names mentioned

in this manual are trade marks or registered

trade marks of their respective owners.

Manual: Evolution Series ES-180S RGY 3D

page 3 / 22

Content:

1. Scope of delivery & details

2. Preliminary warning notices

3. Initial operations, safety instructions

4. Working on the device

5. Service notes

6. Warnings and other notices on the device

7. Device connections

8. Operation

Final statement

Technical data sheet

Laser specications

Manual: Evolution Series ES-180S RGY 3D

page 4 / 22

1. Scope of delivery & details

Please check if all listed parts are included and undamaged. Included in delivery:

1 x laser projector 1 x key

1 x power cable

1 x manual

3. Initial operations, safety instructions

1. Make sure to use correct voltage; see in-

formation on device & in this manual.

2. Make sure that the device is not connec-

ted to mains during installation.

3. Installation has to be done by technical

experienced and qualied persons ac-

cording to safety regulations of the res-

pective country.

4. Always ensure that maximum permissib-

le exposure (MPE) is not exceeded in are-

as accessible to the public.

5. In some countries an additional ins-

pection by technical control institutes

could be necessary.

6. Connect an easily accessible inter-

lock connector or circuit breaker

to the projector.

7. The power supply should be easily acces-

sible.

8. When installing the laser mount it with

a minimum distance of 15 cm from walls

and objects.

9. For safe setup e.g. on walls or ceilings

please use a safety cord. The safety cord

should be able to withstand tenfold the

weight of the device. Please follow the

accident prevention regulations of pro-

fessional associations and/or comparable

regulations for accident prevention.

10. If the device has been exposed to great

temperature changes, do not switch

it on immediately. Condensation water

may damage device.

2. Preliminary warning notices

1. Please use this device only according to these operating instructions.

2. Do not use the device if there are any visible damages on housing, connector panels,

power supplies or power cords.

3. Never look directly into the light source of a laser projector. Danger of blindness!

4. Do not operate the device at high humidity, in the rain or in dusty environments.

5. Protect device against dripping or splashing water. Do not place any liquid lled

containers at the device.

Warranty claim expires with removal of warranty label.

Manual: Evolution Series ES-180S RGY 3D

page 5 / 22

11. Never use dimmer, RC or other electroni-

cally switched sockets. Whenever possib-

le, do not use the laser projector together

with large appliances (especially fog ma-

chines) on the same mains!

12. Ensure sucient ventilation and do not

place the device on any warm or heat ra-

diating surface. Especially the ventilati-

on openings must not be covered!

13. Ensure that device does not get over-

heated. Make sure that the device is not

exposed to spotlights (especially moving

heads). Heat of spotlights could overheat

laser in a little while and leads to a degra-

dation of performance.

4. Working on the device

1. Be sure that the mains plug is not connected to the power sup-

ply while installing or opening the device (e.g. for cleaning).

2. Take o all reecting things like rings, watches etc. before

starting to work with or at the projector.

3. Only use non-reecting tools to work on the device.

4. Wear protective clothing (like goggles, gloves etc.) accor-

ding to laser power and wavelength of the laser.

5. Service notes

• Moisture and heat can reduce lifetime of

the laser system dramatically and expires

any warranty claim.

• Quick on/o switching of device can re-

duce durability of the laser diode drama-

tically.

• Avoid concussions during transport.

• To increase durability of your laser,

protect device against overheating:

-Always ensure sucient ventilation.

-Do not face spotlights (especially mo-

ving heads) to the device.

-Check temperature after approx. 30

minutes with each new installation.

If necessary install the projector at a

place with dierent temperature.

-Keep the device dry. Protect it from

moisture, rain and damp.

-Switch o device when it is not nee-

ded. Diodes are switched on and can

wear o even if there is no visible la-

ser output.

• Open the device at regular intervals and

remove any dust, particularly around fans

and laser. Otherwise the risk of overhe-

ating is imminent and will void the war-

ranty.

• If there are traces of fog uid in the pro-

jector, clean it and change the position of

the fog machine.

• The devices of Ecoline, Evolution and

Club-Series are not meant for professio-

nal applications. After approx. one hour

of operation, the device should cool

down for about 15 minutes.

Manual: Evolution Series ES-180S RGY 3D

page 6 / 22

• As for troubleshooting, please check the

FAQ on our website www.laserworld.com

• Removal of the warranty label as well

as damages to the device caused by

improper handling, neglect of the sa-

fety instructions and service notes will

void the warranty.

6. Warnings and other notices on the device

Laser radiation!

Avoid exposure

to beam.

Laser class 3b

Caution of

radiation if cover

is removed power supply

& consumption

model type

wavelength

Output power

production

year

Please read manual before operation

Use in enclosed spaces only!

7. Device connections

Laser outlet

LED signal

Microphone Regulator for sensitivity control

Manual: Evolution Series ES-180S RGY 3D

page 7 / 22

8. Operation

1. Connect the power cable to the device and then to the mains

2. Use the supplied key to turn on the key switch

3. Press‚ON‘ to switch on your device

4. Your device runs in auto mode:

5. Your device runs in music mode:

6. Control the music-sensitivity by the trim pot at the front side of the device. The LED is

ashing when the device is triggered.

7. Your device runs in DMX mode if ‘10‘ is switched o:

connection for

power supply

DMX address

DMX out

DMX in

LED signal

Key switchfan

power switch

Manual: Evolution Series ES-180S RGY 3D

page 8 / 22

8. Connect a DMX controller to operate the laser.

9. Use the switches 1 - 9 to set the DMX address of the laser. Each switch represents a num-

ber. To dene a number use the preceding number and multipy it by 2:

This laser uses 13 DMX channels, so make sure that the next device uses an address that

doesn’t overlap with this range.

Channel Value Function

1 0 - 64 Laser o

65 - 127 Sound mode

128 - 191 Automatic mode

192 - 255 DMX mode

2 0 - 167 Pattern selection

168 - 255 Animations

3 0 - 255 Flashing patterns with increasing speed

Horizontal movement

4 0 - 167 manual movement

168 - 255 automatic movement with increasing speed

Vertical movement

5 0 - 167 manual movement

168 - 255 automatic movement with increasing speed

Zoom / size

6 0 - 10 no eect

11 - 104 manual size settings

105 - 154 automatic pattern enlargement with increasing

speed

155 - 204 automatic pattern contraction with incresaing

speed

205 - 255 automatic change of enlargement and contrac-

tion with increasing speed

Vertical cross mirroring

7 0 - 150 manual mirroring

151 - 255 automatic mirroring with increasing speed

Switch 12345678910

Number 1 2 4 8 16 32 64 128 256 Mode Switch

Manual: Evolution Series ES-180S RGY 3D

page 9 / 22

Channel Value Function

Horizontal cross mirroring

8 0 - 150 manual mirroring

151 - 255 automatic mirroring with increasing speed

Rotation

9 0 - 180 manual CW rotation

181 - 217 automatic CW rotation with increasing speed

218 - 255 automatic CC rotation with increasing speed

10 0 - 63 no eect

64 - 127 dot-line eects

128 - 191 line eects

192 - 255 dot eects (with blanking)

11 0 - 10 no eect

11 - 255 3D eects: smooth movements with increasing

speed

Color selection

12 0 - 31 red - green - yellow

32 - 63 green

64 - 127 red

128 - 162 red - green

163 - 191 manual color change: red - green

192 - 223 automatic color change: red - green

223 - 255 color change music mode: red - green

13 0 - 8 no eect

9 - 150 manual picture layout

151 - 255 automatic picture layout with increasing speed

10. Please note that not each pattern can be combined with each eect.

11. To use the Daisy Chain Setting, connect both (or more) projectors with (a) DMX cable(s)

through DMX out and DMX in. The rst laser projector in the row is the master projec-

tor. If the Daisy Chain Setting is active, the following projector(s) display(s) the same

patterns etc. like the master projector.

Manual: Evolution Series ES-180S RGY 3D

page 10 / 22

Auto mode + Daisy Chain:

Music mode + Daisy Chain:

12. To turn o the device, press the power switch („OFF“), turn o the key switch and dis-

connect the power cable from the mains.

Master projector following projector(s)

following projector(s)Master projector

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Equipo de DJ de Laserworld

Laserworld

Laserworld Fogscreen Down Manual de usuario

Laserworld

Laserworld Club Series Manual de usuario

Laserworld

Laserworld Purelight Series Manual de usuario

Laserworld

Laserworld Club Series Manual de usuario

Laserworld

Laserworld Proline Series Manual de usuario

Laserworld

Laserworld Garden GS-50RG Xmas Manual de usuario

Laserworld

Laserworld Proline Series Manual de usuario

Laserworld

Laserworld Garden Star Series Manual de usuario

Laserworld

Laserworld CS-400RGB Manual de usuario

Laserworld

Laserworld BeamBar Series Manual de usuario

Laserworld

Laserworld Ecoline Series Manual de usuario

Laserworld

Laserworld RTI ATTO Series Manual de usuario

Laserworld

Laserworld EL-250RGY Manual de usuario

Laserworld

Laserworld CS-400RGY Manual de usuario

Laserworld

Laserworld Fogscreen UP Manual de usuario

Laserworld

Laserworld BeamBar Series Manual de usuario

Laserworld

Laserworld tarm 2.5 FB-4 Manual de usuario

Laserworld

Laserworld Ecoline Series Manual de usuario

Laserworld

Laserworld Diode Series Manual de usuario

Laserworld

Laserworld CS-2000RGB FX Manual de usuario

Laserworld

Laserworld Pure Micro Series Manual de usuario

Laserworld

Laserworld Ecoline Series Manual de usuario

Laserworld

Laserworld CS-250RGY Manual de usuario

Laserworld

Laserworld Ecoline Series Manual de usuario

Manuales populares de Equipo de DJ de otras marcas

ALPHA LITE

ALPHA LITE ALPHA 1500 Manual del propietario

Chauvet

Chauvet OVATION E-930VW Manual de usuario

Zumtobel

Zumtobel APHRODITE Home Manual de usuario

Snow Masters

Snow Masters Zig Oscillator Manual de usuario

EuroLite

EuroLite 50530554 Manual de usuario

Beamz

Beamz BUV243 Manual de usuario

thomann

thomann Stairville DJ Lase 40-G MK-III Manual de usuario

Eagletone

Eagletone 6 Eyes Flower Manual de usuario

EuroLite

EuroLite FLD-1508 Manual de usuario

Technical Pro

Technical Pro LG8xSEA Manual de usuario

JB Systems

JB Systems Lounge Laser DMX Manual de usuario

Lightmaxx

Lightmaxx Vega Halo 90 Manual de usuario

Elation

Elation FUZE WASH Z350 Manual de usuario

Maverick

Maverick MK3 WASH Manual de usuario

Infinity

Infinity TF-260C7 Fresnel Manual de usuario

Chauvet

Chauvet EVE E-50Z Manual de usuario

Eliminator Lighting

Eliminator Lighting E 138 Manual de usuario

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manual de usuario