LanParty X48 Manual de usuario

System Board

User’s Manual

This publication contains information that is protected by copyright.

No part of it may be reproduced in any form or by any means or

used to make any transformation/adaptation without the prior writ-

ten permission from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with respect to

the contents or use of this manual and specifically disclaims any ex-

press or implied warranties of merchantability or fitness for any par-

ticular purpose.The user will assume the entire risk of the use or the

results of the use of this document. Further, the manufacturer re-

serves the right to revise this publication and make changes to its

contents at any time, without obligation to notify any person or en-

tity of such revisions or changes.

Trademarks

Windows®98, Windows®98 SE, Windows®ME, Windows®2000,

Windows NT®4.0 and Windows®XP are registered trademarks of

Microsoft Corporation. VIA is a registered trademark of VIA Tech-

nologies, Inc. Award is a registered trademark of Award Software,

Inc. Other trademarks and registered trademarks of products ap-

pearing in this manual are the properties of their respective holders.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a residential

installation.This equipment generates, uses and can radiate radio fre-

quency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communi-

cations. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following meas-

ures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority

to operate the equipment.

2. Shielded interface cables must be used in order to comply with

the emission limits.

Table of Contents

Warranty.................................................................................................

Static Electricity Precaution................................................................

Safety Measures.....................................................................................

About the Package...............................................................................

Before Using the System Board.........................................................

Chapter 1 - Introduction....................................................................

Specifications...................................................................................................................................

Features..............................................................................................................................................

Chapter 2 - Hardware Installation....................................................

System Board Layout ..........................................................................................................

System Memory..........................................................................................................................

CPU.......................................................................................................................................................

Flame-Freezer Heat Sink....................................................................................................

Jumper Settings............................................................................................................................

Rear Panel I/O Ports.............................................................................................................

Bernstein Audio Module......................................................................................................

Internal I/O Connectors.....................................................................................................

Chapter 3 - BIOS Setup......................................................................

Award BIOS Setup Utility.................................................................................................

RAID BIOS.....................................................................................................................................

Updating the BIOS..................................................................................................................

Chapter 4 - Supported Software.......................................................

Chapter 5 - RAID.................................................................................

Chapter 6 - ATI CrossFire Technology.............................................

Appendix A - System Error Message...............................................

Appendix B - Troubleshooting..........................................................

100

102

120

127

136

138

Warranty

1. Warranty does not cover damages or failures that arised from

misuse of the product, inability to use the product, unauthorized

replacement or alteration of components and product specifica-

tions.

2. The warranty is void if the product has been subjected to physi-

cal abuse, improper installation, modification, accidents or unau-

thorized repair of the product.

3. Unless otherwise instructed in this user’s manual, the user may

not, under any circumstances, attempt to perform service, adjust-

ments or repairs on the product, whether in or out of warranty.

It must be returned to the purchase point, factory or authorized

service agency for all such work.

4. We will not be liable for any indirect, special, incidental or

consequencial damages to the product that has been modified

or altered.

Introduction

Static Electricity Precautions

It is quite easy to inadvertently damage your PC, system board,

components or devices even before installing them in your system

unit. Static electrical discharge can damage computer components

without causing any signs of physical damage. You must take extra

care in handling them to ensure against electrostatic build-up.

1. To prevent electrostatic build-up, leave the system board in its

anti-static bag until you are ready to install it.

2. Wear an antistatic wrist strap.

3. Do all preparation work on a static-free surface.

4. Hold the device only by its edges. Be careful not to touch any of

the components, contacts or connections.

5. Avoid touching the pins or contacts on all modules and connec-

tors. Hold modules or connectors by their ends.

Important:

Electrostatic discharge (ESD) can damage your processor, disk

drive and other components. Perform the upgrade instruction

procedures described at an ESD workstation only. If such a

station is not available, you can provide some ESD protection

by wearing an antistatic wrist strap and attaching it to a metal

part of the system chassis. If a wrist strap is unavailable, estab-

lish and maintain contact with the system chassis throughout

any procedures requiring ESD protection.

Safety Measures

To avoid damage to the system:

• Use the correct AC input voltage range.....

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis

cover for installation or servicing. After installation or servicing,

cover the system chassis before plugging the power cord.

Battery:

• Danger of explosion if battery incorrectly replaced.

• Replace only with the same or equivalent type recommend

the manufacturer.

• Dispose of used batteries according to local ordinance.

Introduction

About the Package

The system board package contains the following items. If any of

these items are missing or damaged, please contact your dealer or

sales representative for assistance.

;One system board

;One Bernstein audio module with cable

;One Flame-Freezer heat sink kit

;One IDE round cable

;One floppy round cable

;Four Serial ATA data cables

;Four Serial ATA power cables

;One I/O shield

;One RAID driver diskette

;One “Mainboard Utility” CD

;One user’s manual

The system board and accessories in the package may not come

similar to the information listed above.This may differ in accordance

to the sales region or models in which it was sold. For more infor-

mation about the standard package in your region, please contact

your dealer or sales representative.

Before Using the System Board

Before using the system board, prepare basic system components.

If you are installing the system board in a new system, you will need

at least the following internal components.

•A CPU

•Memory module

•Storage devices such as hard disk drive, CD-ROM, etc.

You will also need external system peripherals you intend to use

which will normally include at least a keyboard, a mouse and a video

display monitor.

Introduction

Chapter 1 - Introduction

Specifications

Processor

Chipset

System Memory

Expansion Slots

BIOS

Audio

LAN

• LGA 775 socket for:

- Intel®CoreTM2 Quad and Intel®CoreTM2 Duo

• Supports Intel Enhanced Memory 64 Technology (EMT64T)

• Supports Enhanced Intel SpeedStep Technology (EIST)

• Supports Intel Hyper-Threading Technology

• Supports 1600/1333/1066/800MHz FSB

• Intel®chipset

- Northbridge:

Intel®X48 Express chipset

Intel®Fast Memory Access technology

- Southbridge: Intel®ICH9R

• Four 240-pin DDR2 DIMM sockets

• Supports DDR2 667/800 MHz

• Delivers up to 12.8Gb/s bandwidth

• Supports dual channel (128-bit wide) memory interface

• Supports up to 8GB system memory

• Supports unbuffered x8 and x16 DIMMs

• 2 PCI Express (Gen 2) x16 slots (PCIE 1 and PCIE 3)

- 2-way CrossFire at x16/x16 bandwidth

- 2-way CrossFire + Physics at x16/x16/x4 bandwidth

• 1 PCI Express x1 slot (PCIE 2)

• 1 PCI Express x4 slot (PCIE 4)

• 3 PCI slots

• Award BIOS

• 8Mbit flash memory

• CMOS Reloaded

• Bernstein audio module

- Realtek ALC885 8-channel High Definition Audio CODEC

- Center/subwoofer, rear R/L and side R/L jacks

- Line-in, line-out (front R/L) and mic-in jacks

- 2 coaxial RCA S/PDIF-in/out jacks

- 1 optical S/PDIF connector

- 1 CD-in connector

- 1 front audio connector

• DAC SNR/ADC SNR of 106dB/101dB

• Full-rate lossless content protection technology

• Marvell 88E8052 and Marvell 88E8053 PCIE Gigabit LAN

controllers

• Fully compliant to IEEE 802.3 (10BASE-T), 802.3u (100BASE-

TX) and 802.3ab (1000BASE-T) standards

Introduction

Storage

IEEE 1394

Rear Panel I/O

Internal I/O

Power Management

Hardware Monitor

PCB

• Intel ICH9R chip

- Intel Matrix Storage technology

- Supports up to 6 SATA devices

- SATA speed up to 3Gb/s

- RAID 0, RAID 1, RAID 0+1 and RAID 5

• JMicron JMB363 PCI Express to SATA and PATA host controller

- Supports up to 2 UltraDMA 100Mbps IDE devices

- Supports 2 SATA devices

- SATA speed up to 3Gb/s

- RAID 0 and RAID 1

• VIA VT6307

• Supports two 100/200/400 Mb/sec ports

• Mini-DIN-6 PS/2 mouse port and PS/2 keyboard port

• 1 IEEE 1394 port

• 6 USB 2.0/1.1 ports

• 2 RJ45 LAN ports

• 3 connectors for 6 additional external USB 2.0 ports

• 1 connector for an external COM port

• 1 connector for an IEEE 1394 port

• 1 connector for the Bernstein audio module

• 1 front audio connector (on the Bernstein audio module)

• 1 CD-in connector (on the Bernstein audio module)

• 1 S/PDIF connector (on the Bernstein audio module)

• 1 IrDA connector

• 1 CIR connector

• 8 Serial ATA connectors

• 1 40-pin IDE connector

• 1 floppy connector

• 1 24-pin ATX power connector

• 1 8-pin 12V power connector

• 2 4-pin 5V/12V power connectors (FDD type)

• 1 front panel connector

• 6 fan connectors

• 1 diagnostic LED

• EZ touch switches (power switch and reset switch)

• ACPI and OS Directed Power Management

• ACPI STR (Suspend to RAM) function

• Wake-On-PS/2 / Wake-On-USB Keyboard/Mouse

• Wake-On-LAN and Wake-On-Ring

• RTC timer to power-on the system

• AC power failure recovery

• Monitors CPU/system/Northbridge temperature and overheat alarm

• Monitors Vcore/Vdimm/Vnb/VCC5/12V/V5sb/Vbat voltages

• Monitors the speed of the cooling fans

• CPU Overheat Protection function monitors CPU temperature

and fan during system boot-up - automatic shutdown upon sys-

tem overheat

• 6 layers, ATX form factor

• 24.5cm (9.64") x 30.5cm (12")

Introduction

Features

The data transfer rate of the high performance DDR2

technology delivers bandwidth of 12.8 Gb/s and beyond.

That is twice the speed of the conventional DDR with-

out increasing its power consumption. DDR2 SDRAM

modules work at 1.8V supply compared to 2.6V memory voltage

for DDR modules. DDR2 also incorporates new innovations such as

the On-Die Termination (ODT) as well as larger 4-bit pre-fetch

against DDR which fetches 2 bits per clock cycle.

ATI’s CrossFireTM technology drives your

PC to a new peak of performance by

combining multiple GPUs in a single sys-

tem. By connecting a Radeon CrossFire Edition graphics card and a

standard PCI Express graphics card, the power of the dual GPUs

(Graphics Processing Units) within the system will accelerate your

gaming performance and improve image quality.

Aside from dual GPU for 3D rendering, CrossFire’s new feature -

asymmetric processing technology, allows adding another dedicated

GPU for physics processing.The 3 GPUs simultaneously handle Data

Parallel Processing (DPP) computing tasks such as game rendering

and physics in a single system. This provides more realistic cutting

edge 3D graphics to run at high resolutions.

The Realtek ALC885 on the Bernstein audio module

supports 6 audio jacks that provide 8-channel audio

output for advanced 7.1-channel super surround sound

audio system. It is also equipped with a CD-in connector,

front audio connector and S/PDIF output allowing digital connections

with DVD systems or other audio/video multimedia.

Tabla de contenidos

Otros manuales de Placa madre de LanParty

LanParty

LanParty Blood-Iron P45 Elite Series Manual de usuario

LanParty

LanParty Blood-Iron P45 Elite Series Manual de usuario

LanParty

LanParty 790X-M2RS Manual de usuario

LanParty

LanParty Blood-Iron G41-T33 Manual de usuario

LanParty

LanParty Blood-Iron P45 Elite Series Manual de usuario

LanParty

LanParty Blood-Iron LanParty Bi 785G-M35 Manual de usuario

LanParty

LanParty X48-T3RS Manual de usuario

LanParty

LanParty P45 T2RS Manual de usuario

LanParty

LanParty DK P45-T3RSB Plus Manual de usuario

LanParty

LanParty NFII Ultra A+ Manual de usuario

LanParty

LanParty NFII Ultra A+ Manual de usuario

LanParty

LanParty 790GX M2RS Manual de usuario

LanParty

LanParty JR 790gx m2rs Manual de usuario

LanParty

LanParty X48-T3RS Manual de usuario

LanParty

LanParty X58-T3EH6 Manual de usuario

LanParty

LanParty Blood-Iron P45 Elite Series Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario