Lang CLF-15-U Instrucciones de funcionamiento
Lang Manufacturing Company 6500 Merrill Creek Parkway Everett, WA 98203
Phone: 425-349-2400 Fax: 425-349-2733
WWW.LANGWORLD.COM © Copyright 2000
Installation, Operation, Maintenance, & Troubleshooting
Model: CLF-15-U Electric Cruise Line Fryer
Serial:
2
THIS MANUAL MUST BE RETAINED FOR FUTURE REFERENCE.
READ, UNDERSTAND AND FOLLOW THE INSTRUCTIONS AND
WARNINGS CONTAINED IN THIS MANUAL.
FOR YOUR SAFETY
DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE
VAPORS AND LIQUIDS IN THE VICINITY OF THIS OR ANY
OTHER APPLIANCE.
WARNING: IMPROPER INSTALLATION, ADJUSTMENT,
ALTERATION, SERVICE OR MAINTENANCE CAN CAUSE
PROPERTY DAMAGE, INJURY OR DEATH. READ THE
INSTALLATION, OPERATING AND MAINTENANCE
INSTRUCTIONS THOROUGHLY BEFORE INSTALLING OR
SERVICING THIS EQUIPMENT.
NOTICE: THIS EQUIPMENT IS APPROVED FOR INSTALLATION ONLY ON
VESSELS GREATER THAN 65 FEET IN LENGTH, IN ACCORDANCE WITH
USCG REGULATIONS IN TITLE 46 CFR 110-113. ANY WIRING USED IN
THE INSTALLATION OF THIS APPLAINCE MUST BE STRANDED COPPER.
3
TABLE OF CONTENTS
CHAPTER PAGE
1. TABLE OF CONTENTS ............................................................................... 3
2. READ FIRST ................................................................................................. 4
3. UNPACKING................................................................................................. 6
4. INSTALLATION ........................................................................................... 7
5. INITIAL START-UP ..................................................................................... 8
6. OPERATION.................................................................................................. 9
7. CLEANING & MAINTENANCE PROCEDURES...................................... 10
8. TROUBLESHOOTING ................................................................................. 12
9. PARTS LISTS ................................................................................................ 14
10. EXPLODED VIEW........................................................................................ 16
11. WIRING DIAGRAMS ................................................................................... 19
12. WARRANTY ................................................................................................. 20
4
IMPORTANT READ FIRST IMPORTANT
CAUTION: THE FRYER WEIGHS 145 LBS. (65.91 KILOGRAMS).
FOR SAFE HANDLING, INSTALLER SHOULD OBTAIN
HELP AS NEEDED, OR EMPLOY APPROPRIATE
MATERIALS HANDLING EQUIPMENT (SUCH AS A
FORKLIFT, DOLLY, OR PALLET JACK) TO REMOVE
THE UNIT FROM THE SKID AND MOVE IT TO THE
PLACE OF INSTALLATION.
CAUTION: ANY STAND, COUNTER OR OTHER DEVICE ON
WHICH FRYER WILL BE LOCATED MUST BE
DESIGNED TO SUPPORT THE WEIGHT OF THE
FRYER (145 LBS.).
CAUTION: SHIPPING STRAPS ARE UNDER TENSION AND CAN
SNAP BACK WHEN CUT.
DANGER: THIS APPLIANCE MUST BE GROUNDED AT THE
TERMINAL PROVIDED. FAILURE TO GROUND THE
APPLIANCE COULD RESULT IN ELECTROCUTION
AND DEATH.
WARNING: INSTALLATION OF THE UNIT MUST BE DONE BY
PERSONNEL QUALIFIED TO WORK WITH
ELECTRICITY. IMPROPER INSTALLATION CAN
CAUSE INJURY TO PERSONNEL AND/OR DAMAGE
TO EQUIPMENT. UNIT MUST BE INSTALLED IN
ACCORDANCE WITH ALL APPLICABLE CODES.
NOTICE: The data plate is located behind the front control
panel. The fryer voltage, wattage, serial number, wire
size, and clearance specifications are on the data
plate. This information should be carefully read and
understood before proceeding with the installation.
NOTICE: The installation of any components such as a vent
hood, grease extractors, fire extinguisher systems,
must conform to their applicable National, State and
locally recognized installation standards.
CAUTION: NEVER ENERGIZE THE HEATING ELEMENTS WITH
NO OIL IN THE KETTLE OR WITH THE OIL LEVEL
MORE THAN 3 INCHES FROM THE LOWER FILL
LEVEL.
CAUTION: ALWAYS KEEP THE AREA NEAR THE APPLIANCE
FREE FROM COMBUSTIBLE MATERIALS.
CAUTION: KEEP FLOOR IN FRONT OF EQUIPMENT CLEAN
AND DRY. IF SPILLS OCCUR, CLEAN IMMEDIATELY,
TO AVOID THE DANGER OF SLIPS OR FALLS.
5
IMPORTANT READ FIRST IMPORTANT
WARNING: ALWAYS TURN THE FRYER POWER SWITCH OFF
BEFORE LIFTING THE HEATING ELEMENTS OUT OF
THE FRYER OIL.
WARNING: BE SURE TO DRAIN THE OIL INTO A SUITABLE
CONTAINER.
WARNING: KEEP WATER AND SOLUTIONS OUT OF CONTROLS.
NEVER SPRAY OR HOSE CONTROL CONSOLE,
ELECTRICAL CONNECTIONS, ETC.
CAUTION: MOST CLEANERS ARE HARMFUL TO THE SKIN, EYES,
MUCOUS MEMBRANES AND CLOTHING.
PRECAUTIONS SHOULD BE TAKEN TO WEAR RUBBER
GLOVES, GOGGLES OR FACE SHIELD AND
PROTECTIVE CLOTHING. CAREFULLY READ THE
WARNING AND FOLLOW THE DIRECTIONS ON THE
LABEL OF THE CLEANER TO BE USED.
NOTICE: Service on this, or any other, LANG appliance must be
performed by qualified personnel only. Consult your
authorized service station directory or call the factory at
1-800-224-LANG (5264), or WWW.LANGWORLD.COM for
the service station nearest you.
WARNING: BOTH HIGH AND LOW VOLTAGES ARE PRESENT
INSIDE THIS APPLIANCE WHEN THE UNIT IS
PLUGGED/WIRED INTO A LIVE RECEPTACLE. BEFORE
REPLACING ANY PARTS, DISCONNECT THE UNIT
FROM THE ELECTRIC POWER SUPPLY.
CAUTION: USE OF ANY REPLACEMENT PARTS OTHER THAN
THOSE SUPPLIED BY LANG OR THEIR AUTHORIZED
DISTRIBUTORS CAN CAUSE BODILY INJURY TO THE
OPERATOR AND DAMAGE TO THE EQUIPMENT AND
WILL VOID ALL WARRANTIES.
6
UNPACKING
3.1 Receiving the Fryer
Upon receipt, check for freight damage, both visible and concealed. Visible
damage should be noted on the freight bill at the time of delivery and signed by the
carrier's agent. Concealed loss or damage means loss or damage, which does not
become apparent until the merchandise has been unpacked. If concealed loss or
damage is discovered upon unpacking, make a written request for inspection by the
carrier's agent within 15 days of delivery. All packing material should be kept for
inspection. Do not return damaged merchandise to Lang Manufacturing Company.
File your claim with the carrier.
3.2 Location
Prior to un-crating, move the fryer as near its intended location as practical. The
crating will help protect the unit from the physical damage normally associated
with moving it through hallways and doorways.
3.3 Un-crating
The fryer will arrive completely assembled inside a wood frame covered by
cardboard box and strapped to a skid. Remove the cardboard cover, cut the
straps and remove the wood frame.
CAUTION: FRYER WEIGHS 145 LBS (65.91 kilograms). FOR SAFE
HANDLING, INSTALLER SHOULD OBTAIN HELP AS
NEEDED, OR EMPLOY APPROPRIATE MATERIALS
HANDLING EQUIPMENT (SUCH AS A FORKLIFT,
DOLLY, OR PALLET JACK) TO REMOVE THE UNIT
FROM THE SKID AND MOVE IT TO THE PLACE OF
INSTALLATION.
CAUTION: ANY STAND, COUNTER OR OTHER DEVICE ON WHICH
FRYER WILL BE LOCATED MUST BE DESIGNED TO
SUPPORT THE WEIGHT OF THE FRYER (145 LBS.).
CAUTION: SHIPPING STRAPS ARE UNDER TENSION AND CAN
SNAP BACK WHEN CUT.
Remove fryer from skid and place in intended location.
7
INSTALLATION
DANGER: THIS APPLIANCE MUST BE GROUNDED AT THE
TERMINAL PROVIDED. FAILURE TO GROUND THE
APPLIANCE COULD RESULT IN ELECTROCUTION AND
DEATH.
WARNING: INSTALLATION OF THE UNIT MUST BE DONE BY
PERSONNEL QUALIFIED TO WORK WITH ELECTRICITY.
IMPROPER INSTALLATION CAN CAUSE INJURY TO
PERSONNEL AND/OR DAMAGE TO EQUIPMENT. UNIT
MUST BE INSTALLED IN ACCORDANCE WITH ALL
APPLICABLE CODES.
NOTICE: The data plate is located behind the front control panel.
The fryer voltage, wattage, serial number, wire size, and
clearance specifications are on the data plate. This
information should be carefully read and understood
before proceeding with the installation.
NOTICE: The installation of any components such as a vent hood,
grease extractors, fire extinguisher systems, must
conform to their applicable National, State and locally
recognized installation standards.
4.1 Electrical Connection
Electrical service may be made through a standard 1¼-inch conduit. A hole should
be cut out in one of two locations, the first is behind the unit on the right side (if
looking from the back). It should be made 3” from the side and 3” from the
bottom. The second location is on the bottom back right corner (if looking form
the back). It should be made 2” from the side, and 3” from the back. Check the
National Electrical Code for fuse for circuit breaker requirements.
4.2 Fryer Voltage
The Lang Model CLF-15-U can be operated on 480 Volts.
8
INITIAL START UP
5.1 PRE-POWER ON
Boil Out Fryer
Ensure the elements are lowered into the fry pot. Fill the fry pot with a mixture of
Vinegar and water (1:10 mix). Fill until the Vinegar and water level is maintained
between the lower and upper fill marks. Heat to 200°F and let stand for 30
minutes. After 30 minutes drain water and vinegar mix (see operation section for
instructions). Be sure to wipe out and dry fry pot to remove any water spots.
Fill levels
There are two fill marks on the sides of the fryer kettle. The lower level indicates
the fill mark with the elements out, the upper level indicates the fill mark when the
elements are lowered. Fill and maintain the oil level between the upper and lower
levels.
9
OPERATION
CAUTION: NEVER ENERGIZE THE HEATING ELEMENTS WITH
NO OIL IN THE KETTLE OR WITH THE OIL LEVEL
MORE THAN 3 INCHES FROM THE LOWER FILL
LEVEL.
CAUTION: ALWAYS KEEP THE AREA NEAR THE APPLIANCE
FREE FROM COMBUSTIBLE MATERIALS.
CAUTION: KEEP FLOOR IN FRONT OF EQUIPMENT CLEAN AND
DRY. IF SPILLS OCCUR, CLEAN IMMEDIATELY, TO
AVOID THE DANGER OF SLIPS OR FALLS.
6.1 Controls
The power switch, located on the control box at the front of the fryer, energizes the
control circuits. When this switch is on, the “power” pilot lamp will be illuminated.
Turn the temperature selector dial to the desired temperature setting. This control is
located next to the power switch. The “heat” pilot lamp will illuminate indicating
power is applied to the heating elements.
The lamp marked “overtemp” will illuminate if the oil reaches an over-temperature
condition. The over-temperature thermostat shuts off the fryer before the oil
reaches a dangerously high temperature.
6.2 Heating Elements
The elements may be raised and locked in the up position. The latch is located on
the rear top surface of the fryer and may be activated by lifting the handle at either
side of the fryer.
6.3 Draining the Fryer Oil
WARNING: ALWAYS TURN THE FRYER POWER SWITCH OFF
BEFORE LIFTING THE HEATING ELEMENTS OUT OF
THE FRYER OIL.
WARNING: BE SURE TO DRAIN THE OIL INTO A SUITABLE
CONTAINER.
A drain valve is provided inside the lower cabinet door.
To drain the cooking oil remove the steel cap from the drain pipe located at the
bottom, lower, front left corner of the fryer. Connect a drain pipe extension to the
drainpipe. Pull the lever located in the front bottom left corner of the fryer.
10
MAINTENANCE & CLEANING
7.1 Daily Cleaning
WARNING: KEEP WATER AND SOLUTIONS OUT OF CONTROLS.
NEVER SPRAY OR HOSE CONTROL CONSOLE,
ELECTRICAL CONNECTIONS, ETC.
CAUTION: MOST CLEANERS ARE HARMFUL TO THE SKIN,
EYES, MUCOUS MEMBRANES AND CLOTHING.
PRECAUTIONS SHOULD BE TAKEN TO WEAR
RUBBER GLOVES, GOGGLES OR FACE SHIELD AND
PROTECTIVE CLOTHING. CAREFULLY READ THE
WARNING AND FOLLOW THE DIRECTIONS ON THE
LABEL OF THE CLEANER TO BE USED.
It is recommended the fryer oil be kept as clean as possible by straining regularly
(several times a day) and filtering daily. This will lengthen the life of your oil and
improve the performance of the fryer.
7.2 Daily Severe Duty Cleaning
1. Turn power switch off.
2. Remove the baskets, let baskets drain and then set aside.
3. Raise heating elements out of oil and lock in up position.
4. Remove cap from oil drainpipe on bottom of fryer.
5. Place a suitable container under drainpipe.
6. Pull drain valve lever forward to open drain valve.
7. Remove loose food particles from heating units with spatula and wire brush.
8. Flush out scrapings and sediment with a small quantity of hot oil, and allow to
drain thoroughly.
9. Close drain valve and fill with a commercial fryer cleaning agent or soapy solution
of non-corrosive grease dissolving cleaner.
10. Lower heating elements and set selector switch to 250ºF (be sure to read and
follow cleaner manufactures instructions) and boil solution for 15 to 20 minutes.
11. Turn power switch off.
12. Raise heating elements and lock in up position, then drain solution from well.
Refill with water and add 1/2 cup of white vinegar to neutralize alkaline left by
soap. Lower heating elements and bring solution to a boil and let stand for a few
minutes.
13. Turn power switch off.
14. Raise heating elements and lock in up position and drain well and rinse with clear,
hot water. Dry well and heating units thoroughly, and close drain valve.
15. Refill fryer with oil, and lower heating elements slowly.
16. Operate fryer as normal.
7.3 Over-Temperature Protection
The over-temperature thermostat located next to the left heating element provides
protection in case of malfunction of the main temperature control. It will open both
the “control contactor” and the “safety contactor” removing all power from the
heating elements.
Tabla de contenidos
Otros manuales de Freidora de Lang
