Landoll 2110 Manual de usuario

F-479-0310 03/2010

LANDOLL CORPORATION

1900 North Street

Marysville, Kansas 66508

(785) 562-5381

800-428-5655 ~ WWW.LANDOLL.COM

Model 2110

Coulter Chisel

Operator’s Manual

F-479-0310 Edition i

Table of Contents

1 Introduction

Understanding Safety Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

2 Standard Specifications

3 Assembly Instructions

2110-07/09 Frame Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

2110-11/13/15 Coulter Chisel Frame Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

Wheel Lift Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

Hitch Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7

Depth Stop Tube Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9

Coulter Gang Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11

Auto Reset Shank and Shovel Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13

Rigid Shear Shank and Shovel Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15

Hydraulic Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17

Light Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19

Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20

Offset Shank Mount Installation (Option) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20

Rear Jack Installation (Option) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-21

Rear Tow Hitch Installation (Option) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-25

Tubular Mount Chopper Reel Installation (Option) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-27

4 Operation and Maintenance

Tractor Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

Coulter Chisel Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

Attaching To The Tractor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

Hydraulic Lift System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

Hydraulic Coulter Gang Lift System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4

General Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4

Field Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

Leveling (Front-to-Rear) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

Variable Ratio Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6

ii F-479-0310 Edition

Coulter Blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-7

Depth Stop Adjustment (Manual) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8

Wheel Bearing Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8

Hydraulic Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9

Transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9

Lubrication Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12

5 Troubleshooting Guide

1-1

Chapter 1

Introduction

The Landoll Model 2110 Coulter Chisel is a quality product designed to give years of trouble free performance. By

following each section of this manual, your system will perform as designed for you and your operation

CHAPTER 1 gives basic instructions on the use of this manual.

CHAPTER 2 gives product specifications. These specifications supply lengths and measures for your

equipment. A Standard Bolt Torque Table is provided to give guidelines for bolt torques to

be used when servicing this product.

CHAPTER 3 contains assembly instructions for your Model 2110 Coulter Chisel. When these

procedures are correctly followed, your equipment should provide you years of

trouble-free operation and service.

CHAPTER 4 instructs how to operate your equipment before using it, and describes adjustments

needed. It also gives practical advice for the care and maintenance of your Landoll

equipment. Drawings in this section locate adjustment points on the equipment.

NOTE: IF THE EQUIPMENT IS IMPROPERLY ASSEMBLED OR MAINTAINED, THE

WARRANTY IS VOID. IF YOU HAVE ANY QUESTIONS CONTACT:

LANDOLL CORPORATION

1900 NORTH STREET

MARYSVILLE, KANSAS 66508

or phone:

(785) 562-5381 or

(800) 428-5655

or FAX:

(888) 527-3909

CHAPTER 5 is a troubleshooting guide to aid in diagnosing and solving problems with the equipment.

PARTS LIST is a separate manual showing the various assemblies, subassemblies, and systems.

Refer to that manual when ordering Landoll replacement parts. Order parts from your

Landoll dealer.

WARRANTY The Warranty Registration form is included with the product documents. Fill it out and

mail it within 15 days of purchase.

NOTE: IMPROPER ASSEMBLY, MODIFICATION, OR MAINTENANCE OF YOUR

LANDOLL MACHINE CAN VOID YOUR WARRANTY.

COMMENTS Address comments or questions regarding this publication to:

LANDOLL CORPORATION

1900 NORTH STREET

MARYSVILLE, KANSAS 66508

ATTENTION: PUBLICATIONS -DEPT. 55

1-2 F-479-0310 Edition

INTRODUCTION

Understanding Safety

Statements

You will find various types of safety information on the

following pages and on the machine signs (decals)

attached to the vehicle. This section explains their

meaning.

The Safety Alert Symbol means ATTENTION! YOUR

SAFETY IS INVOLVED!



DANGER



WARNING



CAUTION

NOTE

Means that failure to follow these instructions could

cause damage to the equipment or cause it to operate

improperly.

NOTE

Make sure you read and understand the information

contained in this manual and on the machine signs

(decals) before you attempt to operate or maintain this

vehicle.

The safety statements contained in this manual relate to

the operation of the Model 2110 Coulter Chisel.

Danger means a life-threatening situation exists.

Death can occur if safety measures or

instructions on this label are not properly

followed.

Warning means serious injury or death can occur

if safety measures or instructions on this label

are not properly followed.

Caution means serious equipment or other

property damage can occur if instructions on this

label are not properly followed.

INTRODUCTION

1-3

Notes

1-4 F-479-0310 Edition

INTRODUCTION

Page Intentionally Blank

2-1

Chapter 2

Standard Specifications

2110 SERIES COULTER CHISEL W/ AUTO RESET SHANKS

MODEL NO. 2110-07 2110-09 2110-11 2110-13 2110-15

WORKING WIDTH 8’-9” 11’-3” 13’-9” 16’-3” 18’-9”

TRANSPORT WIDTH 9’-10” 11’-9” 14’-4” 16’-10” 19’-4”

BLADE DIAMETER 22” 22” 22” 22” 22”

NO. OF BLADES 15 19 23 27 31

NO. OF BEARINGS 44 6 68

TIRE AND WHEELS (2) 12.5L x 15,

12 ply - 6 bolt (4) 12.5L x 15,

12 ply - 6 bolt

ESTIMATED WEIGHT (LBS.) 7,621 10,258 11,200 12,142 13,059

Specifications are subject to change without prior notification.

2110 SERIES COULTER CHISEL W/ RIGID SHEARBOLT SHANKS

MODEL NO. 2110-07 2110-09 2110-11 2110-13 2110-15

WORKING WIDTH 8’-9” 11’-3” 13’-9” 16’-3” 18’-9”

TRANSPORT WIDTH 9’-10” 11’-9” 14’-4” 16’-10” 19’-4”

BLADE DIAMETER 22” 22” 22” 22” 22”

NO. OF BLADES 15 19 23 27 31

NO. OF BEARINGS 44 6 68

TIRE AND WHEELS (2) 12.5L x 15,

12 ply - 6 bolt (4) 12.5L x 15,

12 ply - 6 bolt

ESTIMATED WEIGHT (LBS.) 6,403 8,405 9,347 9,952 10,532

Specifications are subject to change without prior notification.

TIRE INFLATION

TIRE

SIZE TIRE

MANUFACTURER PLY/LOAD

RATING INFLATION PRESSURE

(psi) (max.)

12.5L x 15 Heavy Duty Titan 20 Ply/4940 lbs. 80 psi

12.5L x 15

Farm Highway Service Goodyear F Load 4680 lbs. 90 psi

12.5L x 15 Goodyear 12 Ply/3860 lbs 52 psi

2-2 F-479-0310 Edition

STANDARD SPECIFICATIONS

Table 2-1: General Torque Specifications

LANDOLL CORPORATION

GENERAL TORQUE SPECIFICATIONS (REV. 4/97)

THIS CHART PROVIDES TIGHTENING TORQUES FOR GENERAL PURPOSE APPLICATIONS WHEN SPECIAL TORQUES ARE NOT SPECIFIED ON PROCESS

OR DRAWING.

ASSEMBLY TORQUES APPLY TO PLATED NUTS AND CAPSCREWS ASSEMBLED WITHOUT SUPPLEMENTAL LUBRICATION (AS RECEIVED CONDITION).

THEY DO NOT APPLY IF SPECIAL GRAPHITE MOLY-DISULFIDE OR OTHER EXTREME PRESSURE LUBRICANTS ARE USED.

WHEN FASTENERS ARE DRY (SOLVENT CLEANED), ADD 33% TO AS RECEIVED CONDITION TORQUE.

BOLT HEAD IDENTIFICATION MARKS INDICATE GRADE AND MAY VARY FROM MANUFACTURER TO MANUFACTURER.

THICK NUTS MUST BE USED ON GRADE 8 CAPSCREWS.

USE VALUE IN [ ] IF USING PREVAILING TORQUE NUTS.

TORQUE IS SPECIFIED IN FOOT POUNDS

UNC

Size SAE Grade

2SAE Grade

5SAE Grade

8UNF

Size SAE Grade

2 SAE Grade

5SAE Grade

1/4-20 4 [5] 6 [7] 9 [11] 1/4-28 5 [6] 7 [9] 10 [12]

5/16-18 8 [10] 13 [16] 18 [22] 5/16-24 9 [11] 14 [17] 20 [25]

3/8-16 15 [19] 23 [29] 35 [43] 3/8-24 17 [21] 25 [31] 35 [44]

7/16-14 24 [30] 35 [43] 55 [62] 7/16-20 27 [34] 40 [50] 60 [75]

1/2-13 35 [43] 55 [62] 80 [100] 1/2-20 40 [50] 65 [81] 90 [112]

9/16-12 55 [62] 80 [100] 110 [137] 9/16-18 60 [75] 90 [112] 130 [162]

5/8-11 75 [94] 110 [137] 170 [212] 5/8-18 85 [106] 130 [162] 180 [225]

3/4-10 130 [162] 200 [250] 280 [350] 3/4-16 150 [188] 220 [275] 320 [400]

7/8-9 125 [156] 320 [400] 460 [575] 7/8-14 140 [175] 360 [450] 500 [625]

1-8 190 [237] 408 [506] 680 [850] 1-14 210 [263] 540 [675] 760 [950]

1-1/8-7 270 [337] 600 [750] 960 [1200] 1-1/8-12 300 [375] 660 [825] 1080 [1350]

1-1/4-7 380 [475] 840 [1050] 1426 [1782] 1-1/4-12 420 [525] 920 [1150] 1500 [1875]

1-3/8-6 490 [612] 110 [1375] 1780 [2225] 1-3/8-12 560 [700] 1260 [1575] 2010 [2512]

1-1/2-6 650 [812] 1460 [1825] 2360 [2950] 1-1/2-12 730 [912] 1640 [2050] 2660 [3325]

1-3/4-5 736 [920] 1651 [2063] 2678 [3347] 1-3/4-12 920 [1150] 2063 [2579] 3347 [4183]

METRIC

COARSE THREAD METRIC CLASS 10.9 FASTENERS AND CLASS 10.0 NUTS AND THROUGH HARDENED FLAT WASHERS, PHOSPHATE COATED, ROCKWELL

“C” 38-45.

USE VALUE IN [ ] IF USING PREVAILING TORQUE NUTS.

Nominal

Thread

Diameter

Standard Torque Nominal

Thread

Diameter

Standard Torque

Newton-

Meters Foot-

Pounds Newton-

Meters Foot-

Pounds

6 10 [14] 7 [10] 20 385 [450] 290 [335]

7 16 [22] 12 [16] 24 670 [775] 500 [625]

8 23 [32] 17 [24] 27 980 [1105] 730 [825]

10 46 [60] 34 [47] 30 1330 [1470] 990 [1090]

12 80 [101] 60 [75] 33 1790 [1950] 1340 [1450]

14 125 [155] 90 [115] 36 2325 [2515] 1730 [1870]

16 200 [240] 150 [180] 39 3010 [3210] 2240 [2380]

18 275 [330] 205 [245]

Otros manuales para 2110

Tabla de contenidos

Otros manuales de Maquinaria agrícola de Landoll

Landoll

Landoll 7812 Manual del producto

Landoll

Landoll WEATHERPROOFER II 2320 FOLD Series Manual de usuario

Landoll

Landoll 5110NG Manual de usuario

Landoll

Landoll 4620-24 Manual de usuario

Landoll

Landoll Brillion 3631-25 Manual de usuario

Landoll

Landoll 1550 Series Manual de usuario

Landoll

Landoll 2512 Series Manual de usuario

Landoll

Landoll ICON 19C Instrucciones de construcción

Landoll

Landoll Coulter Chisel 2112 Manual de usuario

Landoll

Landoll Icon 1205 Carry All Instrucciones de construcción

Landoll

Landoll 6250 Disc Manual de usuario

Landoll

Landoll Wing Tilloll 876 Series Manual de usuario

Landoll

Landoll 8530 Manual de usuario

Landoll

Landoll VT PLUS 7430 Manual de usuario

Landoll

Landoll ICON 6510 Guía de inicio rápido

Landoll

Landoll Brillion 4630-36 Series Manual de usuario

Landoll

Landoll 6231 Manual de usuario

Landoll

Landoll 2110 Manual de usuario

Landoll

Landoll 9630FH Manual de usuario

Landoll

Landoll 6230 Manual de usuario

Landoll

Landoll Brillion LSP5 Manual de usuario

Landoll

Landoll Brillion FPS-6 Manual de usuario

Landoll

Landoll Brillion SL10 Manual de usuario

Landoll

Landoll 7430 Series Manual de usuario

Manuales populares de Maquinaria agrícola de otras marcas

GSi

GSi PNEG-2314 Manual de usuario

Checchi & Magli

Checchi & Magli TEXDRIVE Manual de usuario

Amazone

Amazone Cenius 4003-2TX Manual de usuario

MASSEY FERGUSON

MASSEY FERGUSON MF 9313S Manual de usuario

Cima

Cima BLITZ Instrucciones de funcionamiento y mantenimiento

Amazone

Amazone CombiDisc 3000 Instrucciones de instalación

HE-VA

HE-VA Disc-Roller XL Contour Manual de usuario

AGT

AGT AGT-SSFM Manual de usuario

Milestone

Milestone 72-84 Manual de usuario

KUHN

KUHN Hector 3000 Manual de usuario

Krone

Krone X-Disc 6200 Manual de usuario

Eliet

Eliet DZC450 Manual de usuario

Taarup

Taarup BIO+ B4000 Manual de usuario

Garland

Garland SHAKER 310 DPG Manual de usuario

stable comfort

stable comfort StableWall System Manual de usuario

Raven

Raven AccuBoom Manual de usuario

International

International 710 Manual de usuario

Ashland

Ashland HDW-3217-14 Manual de usuario