Labgear LAB350W Manual de usuario
High Gain Compact Digital Professional Aerial
• Tilting mast clamp for easy adjustment
• Easy dipole assembly
• Unique compact folding design
• 12dB gain
• Length: 790mm
• Electronic 75Ω balun with F type connection
Installation Instructions
Congratulations on the purchase of your compact high gain digital aerial.
The aerial is ideal for the reception of all available signals in medium and strong signal areas.
The aerial is of particularly robust construction to ensure a long operating life and features:
For optimum results install the aerial using double screened CAI
approved digital coax cable (not supplied) and screened coax
outlets (not supplied). You will need to t the coax cable with an
F type connector to connect to the aerial balun.
1. Preparing the coax cable downlead: First slide the
rubber weather boot provided over the aerial end of
the cable. Strip the end of the cable as shown in
Fig. 1. Once you have stripped the cable, fold the
braid back over the outer sheath making sure that no
braid is touching the copper core, as this will cause a
short on the cable and you will not get any signal.
Also cut or tear away any foil shielding.
2. Twist the ‘F’ connector supplied on to the prepared
aerial end of the cable and trim the central conductor
see Fig. 2. Once you have installed your aerial and
run and secured the cable prepare the other end for
connection to an outlet or coax plug (not supplied).
For best results the aerial should be mounted on an
outdoor aerial mast and pointed in the direction of
the nearest transmitter* making sure it is in a position
where the transmitter signal will not be obstructed
by nearby trees and buildings. If you are in any doubt
about the direction in which the aerial should be
pointing or the orientation of the aerial (horizontal for
main transmitter, vertical for relay transmitter) check
your neighbours’ aerials.
1. Unfold the booms as shown opposte. To lock the
booms in position turn both of the two knobs on
either side of the aerial in a clockwise direction
through 180˚ making sure that the arrows line
up with the locked symbol - see Fig. 4.
fold braid back
over sheath
8mm
inner
wire
cut or tear
away foil
6.5mm
Fig. 1
screw connector
body onto cable
2mm approx.
end of
insulation
should be
flush with
this face
Fig. 2
Locking knob
Fig. 3a
Fig. 4 Locked
Symbol
LAB350W USER GUIDE
Fig. 3b
Fig. 3c
2. Next fasten the balun to the underside of the main
boom as shown in Fig. 5. Make sure the balun is the
right way round as shown in Fig. 4 and 8.
3. Fix the reflectors to the main boom using the brackets
and the bolt with wing nut supplied as shown below
in Fig. 6.
Troubleshooting
No picture: Check all connections
from aerial to TV.
Poor picture: Check all connections from aerial to TV.
Check aerial is properly aligned to the correct transmitter.
If the aerial has been loft mounted try mounting outside.
Make sure new digital coax cable has been used
throughout the installation.
Check the transmitter signal is not obstructed by nearby
trees or buildings.
If in a very weak signal area or for long cable runs,
installing a masthead amplifier will improve the signal.
If in a strong signal area the signal strength may need to
be reduced by fitting an attenuator.
Caution
When mounting the assembled aerial, always observe safety
precautions and use the correct equipment.
Unless you are competent in the use of ladders and other
access equipment,do not work outdoors at roof height.
If in any doubt, refer to a qualied aerial installer.
© Philex Electronic Ltd. 2011. v1.2
Fig. 5
4.
Connect the aerial downlead to the ‘F’ socket on the
aerial balun (be careful not to over tighten the
F connector as this will damage the balun).
Ensure
that the weather boot is correctly secured over
the ‘F’ connector and socket - see Fig. 8.
Make sure that the coax cable is routed as
shown in Fig. 8 (through the middle of the
lower reector). Use insulating tape, to
secure the the coax downlead to the
reector and mast.
5.
Use the tilting mast clamp supplied to x
the aerial securely to the mast. To adjust the
tilt angle loosen the two bolts, tilt to
horizontal and then re-tighten nuts (see Fig. 9).
Fig. 6
Fig. 7
Insulating
Tape
Fig. 8
F Connection
Reflector
Weather Boot
Useful Websites for Digital Advice:
*To conrm that your home is in a coverage area, to nd out which
DTT channels should be available locally and to nd out where your
nearest transmitter is visit:
www.dtg.org.uk/industry/coverage.html
and enter postcode.
To nd out your nearest transmitter’s distance and compass bearing
select Trade view from the top bar.
For further information, please contact:
Customer careline: 08457 573479 (Local Rate - UK Only)
Technical Support: www.philex.com/support/
Fig. 9
Loosen
nuts to
adjust tilt
Tabla de contenidos
Otros manuales de Antena de Labgear
Labgear
Labgear LABGT07T Manual de usuario
Labgear
Labgear LAB32KIT/S Manual de usuario
Labgear
Labgear LABHG100 Manual de usuario
Labgear
Labgear LABHG140 Manual de usuario
Labgear
Labgear LABGT20K Manual de usuario
Labgear
Labgear LABHG48A Manual de usuario
Labgear
Labgear LABGT12A Manual de usuario
Labgear
Labgear LAB480W Manual de usuario
Labgear
Labgear LABGT20T Manual de usuario
Labgear
Labgear LABHG420 Manual de usuario
Labgear
Labgear LABGT18A Manual de usuario
Labgear
Labgear LABHG32T Manual de usuario
Labgear
Labgear 29911LAB Manual de usuario
Labgear
Labgear LAB350T Manual de usuario
Labgear
Labgear LABHG52T Manual de usuario
Labgear
Labgear C10W Manual de usuario
Labgear
Labgear 27884LAB Manual de usuario
Labgear
Labgear Wideband High Gain Digital Aerial Manual de usuario
Manuales populares de Antena de otras marcas
Alfa Network
Alfa Network APA-L01 Manual de usuario
Naval
Naval PR-422CA Manual de usuario
Feig Electronic
Feig Electronic ID ISC.ANTH200/200 Series Manual de usuario
TERK Technologies
TERK Technologies TV44 Manual de usuario
Directive Systems & Engineering
Directive Systems & Engineering DSE2324LYRMK Manual de usuario
HP
HP J8999A Manual de usuario
