Label Neptis SMP Manual de usuario
English
Translation of the ORIGINAL INSTRUCTIONS
Operator for
automatic
swing doors
NEPTIS-SMP-16005_GB_Rel.2.2_09/2016 - CD0420GB
GB
SMP
NEPTIS
INDEX:
GENERAL SAFETY WARNINGS page4
GENERAL SAFETY OBLIGATIONS 4
1)MODEL DESCRIPTION 5
2)TECHNICAL SPECIFICATIONS 5
MECHANICAL SECTION
3)COMPONENTS OF THE NEPTIS SMP OPERATOR 6
4)PRELIMINARY CHECKS 7
5)TECHNICAL DRAWINGS 8
5.1) ASSEMBLY OF THE OPERATOR ON THE LINTEL FROM THE HINGE SIDE BDT2 SLIDE PULL ARM 8
5.2) ASSEMBLY OF THE OPERATOR ON THE LINTEL FROM THE HINGE SIDE BSG 150/250 ELBOW ARM 9
5.3) ASSEMBLY OF THE OPERATOR ON THE LINTEL FROM THE SIDE OPPOSITE OF THE HINGE BSS2 ARTICULATED PUSH ARM 10
5.4) ASSEMBLY OF THE OPERATOR ON THE LEAF FROM THE HINGE SIDE BSS2 ARTICULATED PUSH ARM 11
6)MOVEMENT TRANSMISSION ARMS 12
6.1) BDT2 SLIDE PULL ARM 12
6.2) BSG 150 / BSG 250 ELBOW SLIDING ARM 12
6.3) SLIDING GUIDE FOR PULL ARM 13
6.4) BSS2 ARTICULATED PUSH ARM 13
6.5) EXTB-Z TAPERED PIN 14
6.6) EXTENSION FOR EXTC-Z TAPERED PIN 14
7)PREPARING AND ASSEMBLING THE OPERATOR 15
7.1) REQUIRED TOOLS 15
7.2) OPERATOR CONTROL 15
7.3) OPERATOR ASSEMBLY 16
7.4) INSERTING THE ARM'S TAPERED PIN 16
7.5 REMOVING THE TAPERED PIN 16
8) SELECTING THE OPENING DIRECTION IN FUNCTION OF ARM 17
ELECTRONIC SECTION
9)ELECTRIC ARRANGEMENTS 18
10)ELECTRIC CONNECTIONS 19
11)PWN-T POWER SUPPLY MODULE AND ELECTRIC WIRING 20
12)L-NEP LOGIC BOARD 22
13)N-DSEL DIGITAL PROGRAMMER – SCOPE AND CONNECTIONS 22
14)COMMISSIONING OF AUTOMATED DEVICE (INITIAL SET-UP) 23
14.1) FIRST START OF N-DSEL DIGITAL PROGRAMMER 23
14.2) USE OF N-DSEL DIGITAL PROGRAMMER 23
14.3) SERIAL COMMUNICATION SET-UP 23
14.4) INITIAL SET-UP 24
14.5) FUNCTIONAL TESTING 26
14.6) INPUTS DIAGNOSTICS 26
15)PROGRAM SELECTORS 27
15.1) MANUAL PROGRAM SELECTOR 27
15.2) EV-MSEL MECHANICAL KEY SELECTOR 27
15.3) N-DSEL DIGITAL PROGRAMMER USED LIKE PROGRAM SELECTOR 28
16)GENERAL PROGRAMMING MENU 30
17)FUNCTIONS AND REGULATIONS 31
17.1) FUNCTIONS SETTING 31
17.2) PARAMETERS SETTING 35
18)LANGUAGE 39
19)PASSWORD MANAGEMENT 39
19.1) HOW TO CHANGE THE TECHNICAL PASSWORD 40
19.2) HOW TO CHANGE THE PRIMARY PASSWORD 40
19.3) HOW TO CHANGE THE SERVICE PASSWORD 41
19.4) ENABLING USER (primary and service) PASSWORD USAGE 42
19.5) DEACTIVAING THE USER PASSWORD USAGE 42
20)INFORMATION AND EVENTS MEMORY 43
21)MAINTENANCE 45
22)ELECTRIC LOCK APPLICATION 45
22.1) ELECTRIC LOCK / ELECTRIC STRIKE 45
22.2) MAGNETIC LOCK 46
23)SAFETY SENSOR DEVICES 46
23.1) SENSOR OA-EDGE T 46
23.2) SENSOR 4SAFE ON SW 48
23.3) SENSOR TOPSCAN-S 48
24)EN/RF1 RADIO RECEIVER 49
25)DISABLED PEOPLE COURTESY FUNCTION 50
26)DOUBLE LEAF DOOR SET 51
26.1) ELECTRICAL WIRING FOR A DOUBLE LEAF DOOR SET 51
26.2) DOOR SET-UP 51
26.3) FUNCTIONAL TESTING 54
26.4) PEDESTRIAN OPENING 54
26.5) CONSIDERATION ON THE USE OF N-DSEL PROGRAMMER IN A DOUBLE DOOR SYSTEM 55
27)INTERLOCK SYSTEM 56
27.1) INTERLOCK ELECTRIC CONNECTION 56
27.2) INTERLOCK APPLICATION WITH INDEPENDENT INTERNAL RADAR 56
27.3) INTERLOCK APPLICATION WITH ONLY ONE INTERNAL RADAR 57
28)MEANING OF THE ACOUSTIC SIGNAL 58
29)MAINTENANCE PROGRAM 58
DECLARATION OF INCORPORATION OF PARTLY ASSEMBLED MACHINERY 59
4
GENERAL SAFETY OBLIGATIONS
The mechanical and electric installation must be performed by specialised personnel in accordance with current directives
and regulations.
The installer must make sure that the structure to be automated is stable and robust and if necessary, make it this way by making
structural modifications.
Keep product and packaging materials out of children's reach, as they might be a source of danger.
Do not let the children stay or play within the range of the door.
This product was designed and built exclusively for the purpose described in this documentation. Any other use that is not specifically
indicated could adversely impact the condition of the product and the safety of people.
Label accepts no responsibility for incorrect product installation and usage, as well as for any damages caused by changes made
without its prior consent.
Label is not responsible for the construction of the fixtures to be motorised.
The IP31 degree of protection requires that the operator is installed only on the inner side of buildings.
This product cannot be installed in explosive environments or atmospheres, or in the presence of flammable gases or fumes.
Make sure that the characteristics of the electric distribution network are compatible with the technical data indicated in this manual
and that upstream of the system there is an omnipolar switch with an opening distance of the contacts of at least 3mm and a residual
current device.
Connect the ground conduit of the electric system.
The automatic door must be checked, started up and tested by skilled and well-prepared personnel.
A technical dossier must be prepared for every automation as required by the Machine Directive.
Disconnect the power supply before working on the automation and before opening the cover.
Maintenance is of fundamental importance for the proper operation and safety of the automation. Check the efficiency of all parts every
six months.
Use only original spare parts for maintenance and when replacing product components.
Cleaning operations must be performed with the power supply disconnected, using a damp cloth. Do not deposit or let water or other
liquids penetrate into the Neptis SMP operator or the accessories that are part of the system.
GENERAL SAFETY WARNINGS
Carefully read this instruction manual for the safe installation and operation of the automatic door.
Improper installation and incorrect use of the product could cause serious injury.
Keep the instruction manual for future reference.
The installer must provide all the information about operation and provide the system user with the user manual delivered with the
product.
MEANING OF THE SYMBOLS USED IN THESE INSTRUCTIONS
DANGER: Indication of dangerous situations that could cause material damage and personal injury.
WARNING: Identifies the procedures that must be understood and followed to prevent product damage or malfunctions.
NOTE: To point out and place attention on important information.
It is recommended to take out a maintenance contract.
Risk assessment
The automatic swinging doors must be designed and installed in a way to protect users against the risk and danger of crushing, impact
and shearing between the door and adjacent parts near the door.
The person responsible for starting-up the automation must perform a risk assessment based on the place of installation and the type
of users that could use the automatic door.
The dangers of crushing and shearing related to the secondary closing edge must be prevented
either structurally or by supplementary protective measures (rubber covers, for example).
Any residual risks must be properly signalled.
A = Main closing edge
B = Secondary closing edge
C = Opposite closing edge
The Neptis SMP operator, as required by EN16005 standard, must be equipped by protection devices (sensors) in accordance with
EN12978
1) MODEL DESCRIPTION
The Neptis SMP operator has an electro-mechanical motor for opening the pedestrian swing doors.
The electronic control equipment is located inside the operator.
A list of the operator models for Neptis SMP swinging doors produced by Label is provided below:
The Neptis SMP operator can be used with a slide pull arm or with an articulated push arm.
The operator must be installed in indoor environments.
All models are reversible, therefore in the case of a power failure the door can be opened manually.
Before starting with assembly check the technical drawings in paragraph 5. A drawing of the application is provided for every type of
arm, with the installation dimensions and a chart that provides the weight limits based on the length of the door leaf.
The technical data provided in the charts refers to a typical installation, but the data can be influenced by variables present in every
system, such as friction, environmental conditions, alignment of the leaf hinge, etc....
2) TECHNICAL SPECIFICATIONS
POWER SUPPLY
POWER
POWER SUPPLY OF EXTERNAL ACCESSORIES
ELECTRIC MOTOR
115/230Vac +/-10%, 50-60Hz
120W
24Vdc, 1A
24Vdc
5
ARTICOULATED ARM SLIDING ARM
WEIGHT
PROTECTION DEGREE
AMBIENT TEMPERATURE
FREQUENCY OF USE
LIMIT SWITCH AND ANTICRUSHING SAFETY
REACTION TO OBSTACLES
OPENING TIME for 95°
CLOSING TIME for 95°
PAUSE TIME
10,8 Kg.
IP31
-15°C +50°C
continuous
encoder controlled
reversal of direction
4 - 12 seconds adjustable
5 - 15 seconds adjustable
0 - 20 seconds adjustable
OPERATOR WITH BATTERY DIMENSIONS (LxHxD) 730 x 110 x 120 mm
NEPTIS SMP
Min Max Min Max
18 18
72 144
18 18
114 144
15 15
60 120
15 15
95 120
MANUAL CLOSING TORQUE (Nm)
AUTOMATIC CLOSING TORQUE (Nm)
MANUAL TORQUE TO OPEN (Nm)
AUTOMATIC OPENING TORQUE (Nm)
REFERENCE VALUES FORCE
MECHANICAL SECTION
3) COMPONENTS OF THE NEPTIS SMP OPERATOR
6
1
2
3
4
5
6
7
LEGEND:
L-NEP LOGIC CARD
PWN-T ELECTRICAL WIRING AND POWER SUPPLY CARD
GEARMOTOR WITH ENCODER
SPRING PRELOAD REFERENCE LINE
INNER WIRING BETWEEN THE L-NEP and PWN-T CARDS
PLASTIC PLATE
TRANSFORMER
4) PRELIMINARY CHECKS
Before assembling the automation, make sure the following requirements have been met:
• The operator support structure must be solid and must not show any significant deformations.
• The leaf structure must be rigid and robust.
• The leaf pivots must be suitable and in a good condition.
• The lenght and weight of the leaf must lie within the operating limits of the operator (maximum recommended height 3 mt).
• The leaf must move in a regular manner without friction along its entire stroke.
• The door requires mechanical end stops consisting of a mechanical retainer in the opening position and a final stopper when
closed.
The mechanical stop in the open position is not supplied with the operator.
If the wall to which the operator will be fastened is not suitably resistant and reliable, a predrilled metal plate is available, upon request,
to which the Neptis SMP can be fixed.
7
1
3
3
3
2
2
2
4
4
4
Base Operator NEPTIS SMP
Elenco Parti / Part List
Descrizione/Description
Qtà/Qty
Parte/Item
Piastra / Plate1
1
Vite / Screw M6 x 163
2
Rondella / Washer3
3
Vite / Screw M6 x 20
3
4
5) TECHNICAL DRAWINGS
8
9
10
At door open a mechanical end-stop has
to be installed.
Otros manuales para Neptis SMP
1
Tabla de contenidos
Otros manuales de Sistema de apertura de puertas de Label
Label
Label EVOLUS Manual
Label
Label NEXT 75 Manual de usuario
Label
Label NEXT 120s Manual de usuario
Label
Label NEPTIS/LE Manual de usuario
Label
Label NEPTIS PLUS Manual de usuario
Label
Label ETERNA 70 Manual de usuario
Label
Label NEXT 75 Manual de usuario
Label
Label Neptis SMP Manual de usuario
Label
Label ETERNA 90 EASY Manual de usuario
Label
Label T-NFC Manual de usuario
