La Crosse WS-6010U Manual de usuario

Wall Mount

Location

Solar panel

Battery

compartment

Model WS-6010U

Solar Station

QUICK SETUP GUIDE

Solar-powered Transmitter:

Remote transmission of outdoor temperature and humidity to the

Solar Station by 915 MHz signals

LCD will automatically alternate and display the outdoor

temperature and humidity data

Recharge batteries by solar-powered cells

Wall mounting case

Notes:

Solar panel

The solar-powered temperature transmitter uses solar cells to charge the rechargeable

batteries (2 x AAA rechargeable batteries; included).

The rechargeable batteries cannot be replaced.

SOLAR TRANSMITTER OPERATION MODES

Important:

Users need to press the reset key to activate the solar transmitter and link the

transmission to the Solar Station (receiver).

It is important to allow sufficient light to reach the solar panel while activating the solar transmitter.

Make sure the lights are on in the setup room and the solar panel is facing a 60W light bulb or

brighter - do not cover with hands or other objects.

Solar transmitter RESET key:

The solar transmitter has 3 operations modes:

Normal Operation Mode:

This mode occurs when the battery voltage is higher than 2.5V.

The transmitter will measure and transmit the temperature and humidity data to the Solar

Station every 8 seconds.

The environment brightness is checked every 5 seconds

If a dark environment is detected, it will measure and transmit the temperature every 16s.

If the battery voltage is dropped lower than 2.8V, it will measure and transmit the

temperature every 16s

If battery voltage is dropped lower than 2.4V, will go into Idle mode.

Note: only use a small pointed pen to

press the RESET key to re-active the

transmitter into Normal Operation Mode.

RESET key

If the solar transmitter is placed into a dark environment for 72 hours, will goes into Stop

mode.

If the user cover the solar cell for 10 seconds and press the reset button, "StP" will be

displayed on the LCD. Then the transmitter enters STOP mode.

Idle Operation Mode:

This mode occurs when the battery voltage drops lower than 2.4V.

LCD is turned off.

Does not perform temperature measurement and transmission.

The environment brightness is checked every 5 seconds.

If battery voltage is raised higher than 2.5V, the unit will go into Normal mode.

If the solar transmitter is placed into a dark environment for 72 hours, the will go into Stop

mode.

Stop Operation Mode:

This mode occurs when the solar transmitter is placed into a dark environment for 72 hours

or the user covers the solar cell for 10 seconds and presses the RESET button.

The transmitter is in a standby state. The does not perform any operations and the LCD is

off.

Under a bright condition, press the reset button to wake up the transmitter into normal

operation mode (battery voltage is higher than 2.5V).

This is the most power saving mode.

TO INSTALL / REPLACE BATTERY IN THE SOLAR STATION

The Solar Station can use either the included 2 x alkaline rechargeable batteries (charged by

solar panel; included) or 2 x AA alkaline battery (non-rechargeable; not included).

INITIAL SETUP

It is very important to follow these steps:

1. First, remove the label covering over the battery compartment on the back.

2. Open the battery compartment, and MAKE SURE that the battery switch is in the

BATTERY position (not the SOLAR position).

Battery switch in the BATTERY position

3. Now locate the battery insulator tab, and gently pull to remove it.

4. Slide the battery switch to the SOLAR position

5. Battery switch in the SOLAR position

6. Continue to section titled “Setup After Changing/Installing the Battery in the Solar

Station”

TO INSTALL / REPLACE BATTERIES

The included alkaline rechargeable batteries should provide you with many years of service. If

your batteries need to be replaced, we suggest you use 2 fully charged the AA Alkaline.

Rechargeable batteries should be fully charged before inserting into clock. Alkaline

rechargeable batteries must be used.

If you choose to use non-rechargeable batteries, the battery switch MUST be moved to the

BATTERY position (not the SOLAR position). In this position, the solar cells do not charge the

batteries.

REGARDLESS OF THE TYPE OF BATTERIES INSTALLED, THE BATTERY SWITCH MUST

BE IN THE BATTERY POSITION WHEN THE BATTERIES ARE INSERTED.

If rechargeable batteries are used, the Battery switch should be moved to the SOLAR position

AFTER it is has been inserted.

To use non-rechargeable alkaline batteries:

1. Remove the included rechargeable AA batteries from the compartment.

2. Use the switch to select the alkaline battery (see below).

3. Insert the batteries into the compartment, observing the correct polarity (see marking inside

battery compartment.

4. Replace battery cover

Note: For best performance, batteries should be replaced at least once every 2 years to maintain

the best running accuracy. Ensure that the batteries used are new and the correct size.

Use switch to select

which type of batter

will be used before

inserting the batter

into the compartment

Please help in the preservation of the environment and return used batteries to an

authorized depot.

SETUP AFTER CHANGING/REPLACING THE BATTERY IN THE SOLAR STATION

1. After powering up the Solar Station, all LCD segments will light up briefly and it will show

the time (12:00), indoor temperature, date, and indoor humidity.

2. After the batteries are inserted, the Solar Station will start receiving data signal from the

solar transmitter. The outdoor temperature and humidity data should then be displayed on

the solar station. If this does not happen after 2 minutes, the batteries will need to be

removed from both units and reset from step 1.

3. The distance between the Solar Station and the transmitter should not be more than 200

feet (60.96m) to ensure sufficient 915 MHz transmission. (see notes on “Positioning” and

“915 MHz Reception”).

Note: When changing the batteries:

1. Be careful that they do not spring free from the contacts.

2. Press any button 20 times with the batteries removed.

3. Always wait at least 10 minutes after removing batteries before re-inserting; otherwise

start up problems may occur.

TO SET THE TIME

Note: The time will be displayed with “AM” or “PM”for the time from 12:00 noon until 11:59.

1. Press and hold the SET key for 3 seconds to enter the time setting mode.

Rechargeable Alkaline

battery switch position

Primary Alkaline

battery switch position

2. The hour digits will start flashing.

3. Set the desired hours by pressing and releasing the +key followed by pressing the SET

key.

4. Now the minute digits will start flashing.

5. Set the desired minutes by pressing and releasing the +key. If the +key is held, the units

will increase by 5.

6. Press the SET key again to confirm and enter the Solar Mode setting.

SOLAR MODE

The Solar Mode is used for saving the power consumption of the rechargeable battery (Default

setting ON):

1. The characters “ON” or “OFF” will start flashing. By use of the +key select “ON” or

“OFF” to set the solar mode.

2. Press and release the SET key to exit the setting mode and switch back to the normal

display mode.

If the solar mode setting is ON:

The surrounding environment brightness is checked every 5 seconds.

LCD will automatically turn OFF if the environment is too dark.

LCD will automatically turn ON if the environment is bright enough.

No information will be displayed when the LCD is OFF, but all the settings and

operations will remain, except for the temperature and humidity measurements.

If the solar mode setting is OFF:

LCD will remain ON constantly.

STOP MODE

If the Solar Station is placed in a dark environment for 72 hours continually, the clock will go to

the stop mode:

The most power saving condition.

The Solar Station will not perform any operation and the LCD will also be OFF.

Press any key to wake up the Solar Station and to re-activate the transmission with the

solar transmitter.

MIN/MAX: Press and release the PLUS button to view:

Outdoor Temperature minimum and maximum.

Indoor temperature minimum and maximum.

Current display.

RESET MIN/MAX: Press and hold the PLUS button for 10 seconds to reset the

indoor and outdoor minimum and maximum temperatures to current temperatures.

DISPLAY MODES: Press and release the SET button to view

Shows outdoor temperature in the first line on the left side and outdoor

humidity in the second line on the left side. Shows indoor temperature in

the first line on the right side and indoor humidity in the second line on the

right.

Shows outdoor temperature in the first line on the left side and outdoor

humidity in the first line on the right side. Shows indoor temperature in the

second line on the left side and indoor humidity in the second line on the

right side.

Shows indoor temperature in the first line on the left side and indoor

humidity in the first line on the right side. Shows outdoor temperature in the

second line on the left side and outdoor humidity in the second line on the

right side

915MHZ RECEPTION CHECK FOR OUTDOOR SOLAR TRANSMITTER

The Solar Station will receive the outdoor data every 48 seconds. If the temperature data is not

being received 2 minutes after setting up (or the display shows “- - -”), then please check the

following points:

1. The distance of the Solar Station or outdoor transmitter should be at least 6 feet (2 meters)

away from any interfering sources such as computer monitors or TV sets.

2. Avoid placing the receiver onto or in the immediate proximity of metal window frames.

3. Using other electrical products such as headphones or speakers operating on the same

signal frequency (915MHz) may prevent correct signal transmission and reception.

4. Neighbors using electrical devices operating on the 915MHz signal frequency can also

cause interference.

Note: When the 915 MHz signal is received correctly, do not re-open the battery cover of the

Solar Station, as the batteries may spring free from the contacts and force a false reset. Should

this happen accidentally then reset all units (see “TO INSTALL / REPLACE BATTERY IN THE

SOLAR STATION” and “INITIAL SETUP” above) otherwise transmission problems may occur.

The maximum transmission range is 200 feet (60.96 m) from the outdoor transmitter to the Solar

Station (in open space). However, this depends on the surrounding environment and interference

levels. If no reception is possible despite the observation of these factors, all system units have to

be reset (see “TO INSTALL / REPLACE BATTERY IN THE SOLAR STATION” and “INITIAL

SETUP”).

POSITIONING THE SOLAR STATION:

Before permanently mounting, ensure that the Solar Station is able to receive 915MHz signals

from the desired location. In addition, the Solar Clock should be placed in a bright environment for

the rechargeable batteries to be able to recharge.

There are two possible ways to mount the solar station:

Table Stands

Wall Mounting

WALL MOUNTING

1. Install a mounting screw (not included) into a wall—leaving approximately 3/16 of an inch

(5mm) extended from the wall.

2. Place the Solar Station onto the screw, using the hanging hole on the backside. Gently pull

the Solar Station down to lock the screw into place.

Note: Always ensure that the Solar Station locks onto the screw before releasing.

POSITIONING THE SOLAR TRANSMITTER:

It is important to place the solar transmitter in a bright environment for the

rechargeable batteries to be able to recharge.

The solar transmitter can be placed onto any flat surface or wall mounted using the

bracket which doubles as a stand or wall mount base.

To wall mount: Secure the bracket onto a desired wall using the screws and plastic

anchors.

Clip the solar transmitter onto the bracket.

Note: The mounting surface can affect the transmission range. If, for instance, the

unit is attached to a piece of metal, it may then either reduce or increase the

transmitting range. For this reason, we recommend not to place the unit on any metal surfaces or

in any position where a large metal or highly polished surface is in the immediate vicinity (garage

doors, double glazing, etc.). Before securing in place, please ensure that the Solar Station can

receive the 915MHz signal from the solar transmitter at the positions that you wish to place them.

WARRANTY INFORMATION

La Crosse Technology, Ltd provides a 1-year limited warranty on this product against manufacturing

defects in materials and workmanship.

This limited warranty begins on the original date of purchase, is valid only on products purchased and

used in North America and only to the original purchaser of this product. To receive warranty service, the

purchaser must contact La Crosse Technology, Ltd for problem determination and service procedures.

Warranty service can only be performed by a La Crosse Technology, Ltd authorized service center. The

original dated bill of sale must be presented upon request as proof of purchase to La Crosse Technology,

Ltd or La Crosse Technology, Ltd’s authorized service center.

Tabla de contenidos

Otros manuales de Estación meteorológica de La Crosse

La Crosse

La Crosse 308A-146 Manual de usuario

La Crosse

La Crosse S84193 Manual de usuario

La Crosse

La Crosse WM9280 Meteotime Manual de usuario

La Crosse

La Crosse 308-1451 Manual de usuario

La Crosse

La Crosse S88907 Manual de usuario

La Crosse

La Crosse WS272 Manual de usuario

La Crosse

La Crosse EJIN9007L210 Manual de usuario

La Crosse

La Crosse 308-2316 Manual de usuario

La Crosse

La Crosse WS-9060U-IT Manual de usuario

La Crosse

La Crosse 308-1414W Manual de usuario

La Crosse

La Crosse WS6810 Manual de usuario

La Crosse

La Crosse WS-2510 Manual de usuario

La Crosse

La Crosse WS-9065U Manual de usuario

La Crosse

La Crosse 724-1710 Manual de usuario

La Crosse

La Crosse WS-9160Uv2 Manual de usuario

La Crosse

La Crosse CA79080 Manual de usuario

La Crosse

La Crosse WS-7212NU Manual de usuario

La Crosse

La Crosse 308-1711 Manual de usuario

La Crosse

La Crosse 308-1711BL Manual de usuario

La Crosse

La Crosse C83100 Manual de usuario

La Crosse

La Crosse WD-2511U Manual de usuario

La Crosse

La Crosse 308-145B Manual de usuario

La Crosse

La Crosse 1910 Hoja de especificaciones

La Crosse

La Crosse WS9257IT Manual de usuario

Manuales populares de Estación meteorológica de otras marcas

Auriol

Auriol AHFL 433 A1 Manual de usuario

NexSens

NexSens G2-HYDROMET Manual de usuario

Hyundai

Hyundai WS 2202 Manual de usuario

IROX

IROX HBVR761 UV-X Manual de usuario

La Crosse Technology

La Crosse Technology C86371 Manual de usuario

ADE

ADE WS 1711 Manual de usuario

Auriol

Auriol z29592 Manual de usuario

Auriol

Auriol 296289 Manual de usuario

Hyundai

Hyundai WS 2266 Manual de usuario

La Crosse Technology

La Crosse Technology WS-2210 Manual de usuario

La Crosse Technology

La Crosse Technology WS-811561 Manual de usuario

Ventus

Ventus W177 Manual de usuario

National Geographic

National Geographic VA Colour RC Manual de usuario

Renkforce

Renkforce 1208067 Manual de usuario

Levenhuk

Levenhuk Discovery Report WA40 Manual de usuario

Instant Transmission

Instant Transmission MA 10410 Manual de usuario

Lutron Electronics

Lutron Electronics PHB-318 Manual de usuario

WAREMA

WAREMA EWFS Weather station eco Manual de usuario