Kyocera FS-7000 Manual de usuario
1
English
Deutsch
FrançaisItalianoEspañol
We shall have no liability or responsibility to customers or any other person or
entity with respect to any liability, loss or damage caused or alleged to be caused
directly or indirectly by equipment sold or furnished by us, including but not
limited to, any interruption of service, loss of business or anticipatory profits, or
consequential damages resulting from the use or operation of the equipment or
software.
Caution
NO LIABILITY IS ASSUMED FORANY DAMAGE CAUSED BY IMPROPER
INSTALLATION.
Notice
The information in this manual is subject to change without notification.
Additional pages may be inserted in future editions. The user is asked to excuse
any technical inaccuracies or typographical errors in the present edition.
No responsibility is assumed if accidents occur while the user is following the
instructions in this manual.
The contents of this manual are protected by copyright. No part of this manual may
be reproduced or copied by any means without the permission of the copyright
holder.
Regarding Tradename
PRESCRIBE is a registered trademark of Kyocera Corporation.
2
According to Council Directive 89/336/EEC and 73/23/EEC
Manufacturer’s name: Kyocera Corporation, Printer Division
Manufacturer’s address: 2-14-9 Tamagawadai, Setagaya Ward, Tokyo 158-8610, Japan
declares that the product
Product name: Hard Disk Drive Unit
Model number: HD-2 (as tested with page Printer FS-7000+ and other enhancement
optional units: PF-30, DU-31, DF-31, UF-1 and BC-1)
Conforms to the following product specifications.
EN 55 022:1994 Class B
EN 60 950:1992+A1+A2+A3+A4
The manufacturer and its merchandising companies retain the following technical documentation in
anticipation of the inspection that may be conducted by the authorities concerned.
User’s instruction that conforms to the applicable specifications
Technical drawings
Descriptions of the procedures that guarantee the conformity
Other technical information
KYOCERA ELECTRONICS EUROPE GmbH
Tetsuo Okada, President
Revised Date:
Contact in Europe
KYOCERA ELECTRONICS EUROPE GmbH
Mollsfeld 12
40670 Meerbusch, Germany
Phone: +49 21 59 918 0
Fax: +49 21 59 918 100
Declaration of Conformity
Manufacturer’s name: Kyocera Corporation, Printer Division
Manufacturer’s address: 2-14-9 Tamagawadai, Setagaya Ward, Tokyo 158-8610, Japan
declares that the product
Product name: Hard Disk Drive Unit
Model number: HD-2 (as tested with page Printer FS-7000+ and other enhancement optional
units: PF-30, DU-31, DF-31, UF-1 and BC-1)
Description of device: This Page Printer Model FS-7000+ is the 28ppm; A3 size and utilized plain
paper; laser; dry toner etc.. The printer can be equipped with several
enhancement optional units paper feeder PF-30, duplex unit DU-30, document
finisher DF-30 etc..
3
English
Deutsch
FrançaisItalianoEspañol
Conforms to the following product specifications.
AS/NZS 3548:1995
(EN 55 022: 1994 Class B)
IEC 60 950
(EN 60 950:1992+A1+A2+A3+A4)
The manufacturer and its merchandising companies retain the following technical documentation in
anticipation of the inspection that may be conducted by the authorities concerned.
User’s instruction that conforms to the applicable specifications
Technical drawings
Descriptions of the procedures that guarantee the conformity
Other technical information
David Finn
Managing Director
Date:
Unit 8, 43-45 Herbert Street,
Artarmon NSW 2064, Australia
Phone: +61 2-9-906-8075
Fax: +61 2-9-906-8153
Declaration of Conformity
Model Number: HD-2 (as tested with Printer FS-7000+ and enhancement optional units
FP-30, DU-31, DF-31, UF-1 and BC-1)
Trade Name: Kyocera
Responsible Party: Kyocera Electronics Inc.
Address: 2301-300 Cottontail Lane,
Somerset, NJ 08873, U.S.A.
Telephone number: 732-560-3400
Fax number: 732-560-8380
Contact person for technical matter: Paul Sawchuk
Phone: 732-560-3400
Manufacturer’s name: Kyocera Corporation, Printer Division
Manufacturer’s address: 2-14-9 Tamagawadai, Setagaya Ward,
Tokyo 158-8610, Japan
This device complies with Part 15 of the FCC Rules, Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
The manufacturer and its merchandising companies retain the following technical documentation in
anticipation of the inspection that may be conducted by the authorities concerned.
User’s instruction that conforms to the applicable specifications
Technical drawings
Descriptions of the procedures that guarantee the conformity
Other technical information
KYOCERA ELECTRONICS Inc.
Charles McNulty
General Manager, Printer Division
Date:
4
Warning
FCC Regulations state that any unauthorized changes or modifications to
this equipment not expressly approved by the manufacturer could void the
user’s authority to operate the equipment.
Note: The equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
The equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of the
equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own
expense.
Radio interference requirement in European countries
The optional Hard disk unit HD-2 is intended for use with the printer models FS-
6700/FS-7000/FS-7000+ which are type tested and categorized as a Class B
computing device in accordance with the EN55022 rules.
Device in the Class B category may cause interference to radio or television
reception particularly in a residential installation.
5
English
Deutsch
FrançaisItalianoEspañol
Information to users:
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installa-
tion. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interfer-
ence will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
❒Reorient or relocate the receiving antenna.
❒Increase the separation between the equipment and receiver.
❒Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
❒Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the manufacturer for compli-
ance could void the user’s authority to operate the equipment.
Contents
Precautions for Handling the Hard Disk .................................................................6
Introduction .............................................................................................................7
Names of Parts.........................................................................................................7
Installing the Hard Disk in the Printer.....................................................................8
Hard Disk Initialization (Formatting)......................................................................9
Hard Disk Operation.............................................................................................. 11
Virtual Mail Box (VMB) (Except for FS-7000) ....................................................17
Error Messages ......................................................................................................22
Specifications ........................................................................................................23
6
Precautions for Handling the Hard Disk
When handling the hard disk, adhere to the following precautions.
• The hard disk is delivered in an antistatic bag. To prevent any damage, briefly
touch a large metal object to ensure discharge of static electricity before
removing the hard disk from the bag.
• Never touch the hard disk’s connector section directly with hands.
• When holding the hard disk, do not contact hand with surface of the circuit
board; hold at the edges of the circuit board.
• Never apply force to the metallic portion of the hard disk’s surface.
• Do not touch the exposed portion beneath the hole in the surface with fingers.
• Do not apply undue force when installing.
Note The HD-2 hard disk should be installed by your Kyocera dealer.
Please note that Kyocera may not warrant the hard disk in case of
trouble because the customer has attempted installation by him/
herself.
Metallic surface
portion
Hole
7
English
Deutsch
FrançaisItalianoEspañol
Introduction
The HD-2 is an optional hard disk for use with the Kyocera Page Printer FS-6700/
FS-7000/FS-7000+.
The hard disk is a precision instrument. To ensure correct use, please read this
manual thoroughly so that you understand the correct installation and operation
methods.
Packing List
HD-2 1
Instruction manual (this booklet) 1
Note To enable the use of the HD-2 hard disk, the minimum printer
memory requirement is 8 MB. However, we strongly recommend at
least 12 MB of memory when using this hard disk. Consult an
authorized Kyocera dealer or Service Center for details on the
expansion memory chip.
Names of Parts
Before installing the hard disk, please study the following part names. These names
are used in describing procedures for installing and using the hard disk.
Hard disk cover
Do not apply force.
Connector
Connects to the
connector inside
the printer.
Access lamp
After installation in the
printer, the lamp lights while
the hard disk is accessed.
Hard disk unit
(HD-2)
8
Installing the Hard Disk in the Printer
The HD-2 hard disk is installed in the location marked OPT2 on the rear panel.
CAUTION Before installing (or removing) the HD-2 hard disk, be sure to
turn off the printer’s power and disconnect the power cord
plug from theAC outlet.
It is possible to move an HD-2 hard disk that has been
installed in one printer to another printer if the printers are
the same model. However, if the HD-2 is moved to a different
model printer, data accumulated on the HD-2 will be lost.
Note that in this case, the HD-2 can still be used if it is
formatted, but the accumulated data is lost.
1. Detach the cover over the slot (OPT2) for optional devices as shown in
the illustration.
2. Remove the HD-2 from the package and insert it with care by sliding it
along the rails inside the slot in the printer as shown in the illustration.
3. After proper insertion, clamp the HD-2 using the two screws removed in
step 1above. This completes installation of the hard disk.
Rail
Rail
Cover of the slot (OPT2) for optional devices
Screws
FS-6700 FS-7000/FS-7000+
FS-6700 FS-7000/FS-7000+
9
English
Deutsch
FrançaisItalianoEspañol
Hard Disk Initialization (Formatting)
After installing the hard disk in the printer, the disk must to be initialized (format-
ted) before used. Initialization is performed from the printer’s control panel
following the installation. The initialization procedure is described in the follow-
ing.
1. After confirming that the HD-2 hard disk is installed in the printer, turn
on the printer.
2. The printer’s
ATTENTION
indicator flashes for a while, and the message
display indicates Format error HARD DISK. This is the state when
the printer is turned on the first time after the hard disk has been installed.
Note Even while Format error HARD DISK is displayed, the printer
can be used for normal printing without using the hard disk.
3. Press the printer’s MODE key in this state, and use the +or –key to
display HARD DISK >.
4. When the key is pressed, >Format is displayed.
5. When the ENTER key is pressed, ?is displayed. Press the ENTER key
once more to have the printer initialize (format) the hard disk.
6. When initialization is completed, the printer’s message display changes to
indicate Ready. This completes initialization of the hard disk, which is
now ready for use.
Caution when Turning the Power OFF
To protect the hard disk, always make sure that the printer’s message display
indicates Ready before the printer is turned off.
10
Verifying Installation of the Hard Disk
To verify that the hard disk has been correctly installed and initialized (formatted),
try to print out the printer’s status page.
1. Confirm that the printer’s
ONLINE
indicator is lit and that the message
display indicates Ready.
2. Press the STATUS key on the printer’s control panel.
3. Check the contents of the printed status page. If the Installed Options
and Option 2 items look as follows, there should be no problem.
Note The STATUS PAGE shown above may differ from the actual
printed STATUS PAGE.
Printer STATUS PAGE
Installed Options
Hard-disk drive Installed
Option 2
Hard-disk drive
Write protect OFF
Total 2097152 KB
User available 2096856 KB
Otros manuales para FS-7000
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Manuales populares de Almacenamiento de otras marcas
Spectra Logic
Spectra Logic T-Series Spectra T50e Manual de usuario
Panasonic
Panasonic LKM-F931-1 Manual de usuario
Tabernus
Tabernus Enterprise Erase E2400 Manual de usuario
Rocstor
Rocstor COMMANDER 3F series Manual de usuario
HP
HP P9000 Manual de usuario
Western Digital
Western Digital Ultrastar Data60 Manual de usuario