Kyocera FS-6020 Manual de usuario

$

Page Printer

Installation Guide

Caution

NO LIABILITY IS ASSUMED FOR ANY DAMAGE CAUSED BY IMPROPER INSTALLATION.

Notice on Software

SOFTWARE USED WITH THIS PRINTER MUST SUPPORT THE PRINTER’S EMULATION MODE. The

printer is factory-set to emulate the HP PCL 6. The emulation mode can be changed by following the procedures

described in the Operation Guide contained as an electronic file in the CD-ROM supplied with the printer.

Notice

The information in this manual is subject to change without notification. Additional pages may be inserted in

future editions. The user is asked to excuse any technical inaccuracies or typographical errors in the present

edition.

No responsibility is assumed if accidents occur while the user is following the instructions in this manual. No

responsibility is assumed for defects in the printer’s firmware (contents of its read-only memory).

This manual, any copyrightable subject matter sold or provided with or in connection with the sale of the page

printer, are protected by copyright. All rights are reserved. Copying or other reproduction of all or part of this

manual, any copyrightable subject matter without the prior written consent of Kyocera Mita Corporation is pro-

hibited. Any copies made of all or part of this manual, any copyrightable subject must contain the same copy-

right notice as the material from which the copying is done.

Table of Contents

STEP 1 Unpacking.........................................................................1

STEP 2 Positioning the Printer .....................................................2

STEP 3 Installing the Toner Container .........................................3

STEP 4 Connecting the Printer to the Computer.........................6

STEP 5 Connecting to Power........................................................8

STEP 6 Adding Paper to the Paper Cassette and MP Tray .........9

STEP 7 Turning Power On...........................................................15

STEP 8 Printing a Status Page....................................................16

Revision 1.0 October 2002

Unpacking

Carefully remove the printer and other items from the box. Check that nothing is miss-

ing against the list of shipped components below.

List of Shipped Components

STEP

Printer

(A)

(B)

(C)

Printer

Power Cord (B)

Installation Guide

[this booklet] and

other printed matter

(C)

CD-ROM (C)

To n e r

Container (A)

Positioning the Printer

Make sure that the place of installation meets the following requirements:

Clearance

Be sure to secure enough space

around the printer. Prolonged

use without sufficient clearance

may cause heat to build up

within the printer, resulting in

fire.

Environment

Do not install the printer where temperature or humidity is outside the rec-

ommended range. Print quality may suffer and there will be an increased

chance of paper jams.

Places to Avoid

Avoid installing the printer in locations subject to:

• Direct drafts of hot or cold air

• Direct drafts from outside (Avoid locations near building entrances.)

• Sudden temperature or humidity changes

• Sources of high temperature, for example, near stoves or radiators

•Excessivedust

•Vibration

• Unstable surfaces and surfaces that are not level

• Ammonia or other harmful fumes (If you are planning to fumigate the room, or

make liberal use of insecticide, remove the printer first!)

• Excessive sunlight or humidity

• Lack of ventilation

• Low air pressure, e.g., elevations greater than 2000 meters (6500 feet) above

sea level

Te m p e r a tu r e 10 to 32.5 °C (50 to 90.5 °F), ideally about 23 °C (73.4 °F)

Humidity 20 to 80 %, ideally 60 %

STEP

30 cm

25 cm

60 cm

30 cm

50 cm

Installing the Toner Container

Before you can use the printer for the first time, you must set up the printer by installing

the toner container and the interfacing with the computer.

1Open the printer top cover all the way.

2Confirm that the lock lever is in the

release (UNLOCK) position. If not, pull it

forward until it is in the release posi-

tion.

3Take the toner container from the bag.

4Thoroughly shake the toner container

(in the direction of the arrow) ten times

or more to loosen and mix the toner

inside.

5Carefully remove the protective seal.

STEP

To p C o v e r

Toner Container

10 times or

Protective Seal

6Install the toner container into the

printer.

7Push firmly on the top of the toner con-

tainer at the positions marked PUSH

HERE.

When the toner container fits into

place, it will lock with a clicking sound.

8Push the lock lever to the lock (LOCK)

position.

9Close the top cover.

To remove the toner container

Pull the lock lever #1 to the release

(UNLOCK) position, pull the lock lever

#2 to the right and gently lift the toner

container.

Lock Lever #2

Lock Lever #1

Connecting the Printer to the Computer

There are various ways of connectingthe printer to the computer, such as throughthe

parallel interface connector, through the USB (Universal Serial Bus) interface connec-

tor, through the option serial interface board kit (IB-11) or through the option network

interface card.

Printer Connections

Before performing this step, be sure to turn off both the printer and the com-

puter’s power switches and unplug the printer’s power plug from the power

outlet. Failure to do so may result in electrical shock.

The standard Centronics parallel interface connector ( ) and USB interface

connector ( ) are located on the rear of the printer.

STEP

Printer (Rear)

Parallel Interface

Network Option Network

Interface Card

(3.3 V DC)

Power Supply

USB Interface

Option Serial Interface

Board Kit (3.3 V DC)

Parallel Interface Connection

1Plug one end of the printer cable (not

included) into the parallel interface con-

nector on the rear of the printer.

• Use a parallel printer cable

that complies with the

IEEE1284 standards.

• The printer will work best if it

is installed near the computer.

The connecting cable should

be shielded and not be longer

than 3 meters (10 feet).

2Close the clips on both sides to fix the

connector in place.

Plug the other end of the printer cable

into the computer’s parallel interface

connector.

USB (Universal Serial Bus) Interface Connection

1Plug one end of the USB cable on the

rear of the printer.

•Useacablethatcomplies

with Full-Speed USB 2.0 stan-

dard (a rectangular Type A

plug and a square Type B

plug).

• The connecting cable should

be shielded and not be longer

than 5 meters (16 feet).

2Plug the other end of the USB cable into

the computer’s USB interface connec-

tor.

Clip

USB Cable

Parallel Printer

Cable

Connecting to Power

This section describes the procedure for connecting the power cord and various cau-

tions.

Notes on Power Supply

• Install the printer near an AC wall outlet, preferably one that can be used for

the printer alone.

• Only use this printer with the supply voltage indicated on the serial number

label attached to the printer’s rear panel.

• If an extension cord is used, the total length of the power cord plus extension

should be 5 meters (16 feet) or less.

Power Requirements

To Connect the Power Cord

• Be sure the printer’s power switch is turned off.

• Only use the power cord supplied with the printer.

1Plug the power cord into the power cord

connector on theear of the printer.

2Connect the other end of the power cord

into a power outlet.

Be sure to connect to a 3-wire

grounded power strip.

Voltage 220 to 240 V, ±10 %

Frequency 50/60 Hz (220 to 240V) ±2 %

Current capacity Max. 3.8 A at 220 to 240 V

STEPSTEP

Power Cord

Connector

Power Cord

Otros manuales para FS-6020

Tabla de contenidos

Otros manuales de Impresora de Kyocera

Kyocera

Kyocera FS-1020MFP Manual de usuario

Kyocera

Kyocera ECOSYS FS-6525MFP Manual de usuario

Kyocera

Kyocera ECOSYS FS-1370DN Manual de usuario

Kyocera

Kyocera FS-1120D Manual de usuario

Kyocera

Kyocera Ai3010 Manual de usuario

Kyocera

Kyocera FS-820 Manual de usuario

Kyocera

Kyocera TASKalfa MA3500ci Manual de usuario

Kyocera

Kyocera FS-2020D Manual de usuario

Kyocera

Kyocera ECOSYS FS-1370DN Manual de usuario

Kyocera

Kyocera C5025N - FS Color LED Printer Manual de usuario

Kyocera

Kyocera FS C5030N - Color LED Printer Manual de usuario

Kyocera

Kyocera FS FS-C8500DN Manual de usuario

Kyocera

Kyocera KM-C3130 Manual de usuario

Kyocera

Kyocera Ecosys FS-C5300DN Manual de usuario

Kyocera

Kyocera ECOSYS FS-C2526MFP Manual de usuario

Kyocera

Kyocera DU-61 Manual de usuario

Kyocera

Kyocera ECOSYS M2030dn Manual de usuario

Kyocera

Kyocera ECOSYS P8060cdn Manual de usuario

Kyocera

Kyocera Copystar CS-2035 Manual de usuario

Kyocera

Kyocera FS-1120D Guía de inicio rápido

Kyocera

Kyocera C8100DN - Color Laser Printer Manual de usuario

Kyocera

Kyocera ECOSYS P2035d Manual de usuario

Kyocera

Kyocera Ecosys P2235dn Manual de usuario

Kyocera

Kyocera FS-600 Manual de usuario

Manuales populares de Impresora de otras marcas

Lexmark

Lexmark 1400 Series Manual

Canon

Canon i70 Series Manual de usuario

Evolis

Evolis Elypso Manual de usuario

Canon

Canon LASER SHOT LBP-1210 Manual de usuario

Samsung

Samsung BIXOLON SRP-350plusF Manual de usuario

Canon

Canon PIXMA PRO-1 Series Manual de usuario

Canon

Canon PIXMA G3560 Guía de configuración

Dell

Dell Color Laser Printer 2130cn Manual de usuario

Tektronix

Tektronix Phaser 840 Manual de usuario

Epson

Epson ET-7750 Instrucciones de funcionamiento

Canon

Canon CLBR 460ps Manual de usuario

Eltron

Eltron P210 Guide Manual de usuario

Ricoh

Ricoh MD-P1 Manual de usuario

Epson

Epson SC-F7100 series Manual de usuario

Epson

Epson Stylus C40UX Manual de usuario

Canon

Canon imagePASS-A2 Manual de usuario

Canon

Canon S820D Manual de usuario

IRA3D

IRA3D POETRY4 Manual de usuario