Kyocera ECOSYS P3060dn Manual de referencia
(Page.1/4)
Service Bulletin Ref. No. 2T6-0019 (J010)
<Date> January 25, 2019
KYOCERA Document Solutions Inc.
For authorized KYOCERA engineers only.
Do not distribute to non-authorized parties.
CONFIDENTIAL
A
B
C
Subject:
펌웨어 업그레이드 ( "폐토너 통이 제대로 설치되지
않았습니다."의표시가 사라지는 현상에 대한 시정 조치)
Model:
P3060dn, P3055dn, P3050dn, P3045dn
Classification:
Field measures
timing:
At Set Up Next Periodic Maintenance
Next Visit/Service Call Information only
Phenomenon:
SC/Error Paper Feeding/Conveying Other
Image Machine operation
Type of change:
Hardware Firmware and Software Information
No
Topic
Content
CTL
FW
1
Corrective measures for
the inability of
disappearing the display
of “The waste toner box
is not properly installed.”
Data writing to the EEPROM might be shut off at power off (including
transition to the sleep mode) and might not be complete correctly to
cause not disappearing the display of “The waste toner box is not properly
installed.”
[Change]
1) It is so changed that the power is shut off when confirming the data
writing is complete at power off (including transition to the sleep mode).
2) Process to return the initial value (recovery operation) is added if
upgrading to the new firmware or if data read from the EEPROM is
abnormal.
[Note]
The new firmware recovers the data, however, note if the phenomenon
has occurred, it is in the state below.
A) In case “Toner Low”is displayed after upgrading to the new
firmware, the light image might be printed. ⇒Resolved by replacing
to the new toner container
Reason) In case the status data of detecting “Toner Low”or “Toner
Empty”is abnormal, “Toner Low” or “Toner Empty” status is cleared and
the page count and print coverage printable until “Toner Empty”is
cleared.
･･･If data is recovered with the new firmware, “Toner Low” or “Toner
Empty” is detected again but the page count and print coverage printable
until “Toner Empty”is not recovered. If continuing use, page count until
“Toner Empty”comes to longer and the light image might be printed.
B) In case the toner installation setting is abnormal, the drive time come
to long for more several minutes ⇒No other failure and corrective
measures
2T6-6998
2T6-6997
ENGINE
002.005
2
Improve the recovery
operation at VER002.005
Even if upgrading the firmware for the main unit where there is the failure
of not disappearing the display of “The waste toner box is not properly
installed.”, it might not be resolved.
<This content is to improve the measures for the main unit where this
phenomenon has occurred>
2T6-7006
ENGINE
002.006
(Page.2/4)
Service Bulletin Ref. No. 2T6-0019 (J010)
<Date> January 25, 2019
KYOCERA Document Solutions Inc.
For authorized KYOCERA engineers only.
Do not distribute to non-authorized parties.
CONFIDENTIAL
A
B
C
Type
Program No.
VER.
Remark
CONTROLLER
2T6_S000.002.028
002.028
Except KDHK
ENGINE
2T6_1000.002.005
->2T6_1000.002.006
002.006
New
Upgrade
LANGUAGE BR
2T6_81BR.001.019
001.019
KDA/KDAU/PHILIPPINES & *1
DK
2T6_81DK.001.019
001.019
*1 Danish
NO
2T6_81NO.001.019
001.019
*1 Norwegian
SE
2T6_81SE.001.019
001.019
*1 Swedish
TR
2T6_81TR.001.020
001.020
*1 Turkish
LANGUAGE TW
2T6_81TW.001.009
001.009
AX Asian model/KDTW
CN
2T6_81CN.001.009
001.009
KDCN
KR
2T6_81KR.001.009
001.009
KDKR
For the person who has assigned as a responsibility to access in this new site, it will be possible to download from New Cabi-
Net site ( ALL / PJ ).
When upgrading firmware or replacing PWB, etc., please upgrade each firmware (MAIN, ENGINE, MMI, etc.) to the latest
version at the same time. *1: Pre-installed for KDE/TA/OLIVETTI
Field Measure: Use 002.006 version ENGINE firmware at setup, etc. In case “Toner Low”is displayed after
upgrading the firmware of the field machine to the new version, replace with the new toner
container. (Refer to above A) for details)
First implemented timing at factory: January 2019 production
N00105917/N00106073
Firmware upgrade procedure
In case of setup, next user visit or occurring this phenomenon, upgrade the firmware according to either of the
procedures 1-3 below
1. New machine (Main unit where no power is turned on yet)
(1) Unpack and install it before turning the power switch on. (Refer to the service manual [1-2-2 Unpacking
and installation])
*Howeber, do not attach the waste toner box and do not connect the power cord to the outlet.
(2) Insert a USB drive with the new firmware into the USB host interface slot while the power cord is
disconnected. Connect the power cord to the outlet.
(3) Turn the power on without the waste toner box ⇒Firmware update is executed for about 1 minute.
(4) After confirming the display [FW-Update Completed] (after firmware update is completed), confirm
ENGINEfirmware version is new and [2T6_1000.002.006].
(5) Turn the power switch off, disconnect the power cord and remove the USB drive.
(6) Connect the power cord to the outlet and turn the power switch on.
(7) Confirm [The waste toner box is not properly installed.] or [Select Language] display appears on the
message disply (LCD).
(8) If necessary, repack the main unit. (Reverse procedure of the service manual [1-2-2 Unpacking and
installation) Or attach the waste toner box, connect the power cord to the outlet to continue the installation
(aftr turning the power switch on).
2. Field machine 1 (Main unit operating normally)
(1) Insert a USB drive with the new firmware into the USB host interface slot while the power cord is
disconnected. Connect the power cord to the outlet.
(2) Turn the power on without the waste toner box ⇒Firmware update is executed for about 1 minute.
(Page.3/4)
Service Bulletin Ref. No. 2T6-0019 (J010)
<Date> January 25, 2019
KYOCERA Document Solutions Inc.
For authorized KYOCERA engineers only.
Do not distribute to non-authorized parties.
CONFIDENTIAL
A
B
C
(3) After confirming the display [FW-Update Completed] (after firmware update is completed), confirm
ENGINEfirmware version is new and [2T6_1000.002.006].
(4) Turn the power switch off, disconnect the power cord and remove the USB drive.
(5) Turn the power on and confrim the main unit drives for about 30 seconds and stops to start up normally.
3. Field machine 2 (Main unit where the phenomenon of “The waste toner box is not properly installed.” display
not disappearing)
(1) Insert a USB drive with the new firmware into the USB host interface slot while the power cord is
disconnected. Connect the power cord to the outlet.
(2) Turn the power on ⇒ Firmware update is executed for about 1 minute.
(3) After confirming the display [FW-Update Completed] (after firmware update is completed), confirm
ENGINEfirmware version is new and [2T6_1000.002.006].
(4) Turn the power switch off, disconnect the power cord and remove the USB drive.
(5) Turn the power switch on .⇒ The main unit is only driven with the display of [Please wait, installing
toner] for about 4 minutes.
(Refer to topic 1-B) in the page 1)
*This toner filling operation can be cancelled by pressing [OK] at [Menu] ⇒09 Adjustment/maintenance ⇒
03 Service Settings ⇒06 Toner Install.
(6) Turn the power off when drive stops.
(7) Turn the power on and confrim the main unit drives for about 30 seconds and stops to start up normally.
(Page.4/4)
Service Bulletin Ref. No. 2T6-0019 (J010)
<Date> January 25, 2019
KYOCERA Document Solutions Inc.
For authorized KYOCERA engineers only.
Do not distribute to non-authorized parties.
CONFIDENTIAL
A
B
C
Affected serial number
*1: 92 or later of 4th and 5th digit of serial number Refer to attached file for REWORK serial number (2T6-2TA-REWORK.xlsx).
*002.005is applied to production for the time being. 002.006 is to improve for the machine with failure.
Product name
Destination
Product code
Cut-off serial number
2T6_1000.002.005 applied*
P3060dn
KDA 120V
1102T62US0
*1
KDA 220V
1102T64US0
*1
KDAU
1102T63AS0
*1
KDAS
1102T63AX0
*1
KDHK
1102T63HK0
To be informed later
KDKR
1102T63KR0
To be informed later
KDTW
1102T6TTW0
*1
Philcopy
1102T64PH0
*1
KDCN
1102T63KS0
*1
KDE
1102T63NL0
To be informed later
P-6031DN
TA/UTAX
1102T63UT0
*1
P3055dn
KDA 120V
1102T72US0
To be informed later
KDA 220V
1102T74US0
*1
KDAU
1102T73AS0
To be informed later
KDE
1102T73NL0
VLW9136385
P-5531DN
TA/UTAX
1102T73UT0
To be informed later
PG L2555
OLIVETTI
1102T73LV0
*1
P3050dn
KDA 120V
1102T82US0
VLY9111729
KDAU
1102T83AS0
VM19101769
KDAS
1102T83AX0
To be informed later
KDKR
1102T83KR0
*1
KDTW
1102T8TTW0
To be informed later
Philcopy
1102T84PH0
*1
KDCN
1102T83KS0
*1
KDE
1102T83NL0
VLZ9138461
P-5031DN
TA/UTAX
1102T83UT0
To be informed later
PG L2550
OLIVETTI
1102T83LV0
*1
P3045dn
KDA 120V
1102T92US0
To be informed later
KDA 220V
1102T94US0
*1
KDAU
1102T93AS0
To be informed later
KDAS
1102T93AX0
R1R9102137
KDKR
1102T93KR0
R1C9106554
KDTW
1102T9TTW0
R1H9101441
Philcopy
1102T94PH0
*1
KDCN
1102T93KS0
*1
KDE
1102T93NL0
VM49122645
P-4531DN
TA/UTAX
1102T93UT0
VRC9127090
PG L2545
OLIVETTI
1102T93LV0
VYH9100890
Otros manuales para ECOSYS P3060dn
1
Este manual sirve para los siguientes modelos
3
Otros manuales de Impresora de Kyocera
Kyocera
Kyocera DISCOVER FS-3830N Manual de usuario
Kyocera
Kyocera FS-2000D, FS-3900DN, FS-4000DN, FS-6950DN Manual de usuario
Kyocera
Kyocera ECOSYS M2635dw Manual de instrucciones
Kyocera
Kyocera Ecosys FS-C5300DN Manual de usuario
Kyocera
Kyocera FS-1300D Manual de usuario
Kyocera
Kyocera EcoLAN 3000E Manual de usuario
Kyocera
Kyocera FS-6020 Manual de usuario
Kyocera
Kyocera ECOSYS P6130cdn Manual de usuario
Kyocera
Kyocera ECOSYS FS-6525MFP Manual de usuario
Kyocera
Kyocera ECOSYS FS-C2126MFP Manual de usuario
Kyocera
Kyocera FS-1920 Ecosys Manual de usuario
Kyocera
Kyocera FS-C8026N Manual de usuario
Kyocera
Kyocera FS-1300D Manual de usuario
Kyocera
Kyocera ECOSYS P6230cdn Manual de usuario
Kyocera
Kyocera FS-820 Manual de usuario
Kyocera
Kyocera 1102RW3NL0 Manual de usuario
Kyocera
Kyocera FS-9120DN Manual de usuario
Kyocera
Kyocera TASKalfa MA3500ci Manual de usuario
Kyocera
Kyocera FS-2000D Manual de usuario
Kyocera
Kyocera FS-1800 Manual de usuario
