Kyocera Mita Ecosys FS-1010 Manual de usuario

Page Printer

Installation Guide

Caution

NO LIABILITY IS ASSUMED FOR ANY DAMAGE CAUSED BY IMPROPER INSTALLATION.

Notice on Software

SOFTWARE USED WITH THIS PRINTER MUST SUPPORT THE PRINTER'S EMULATION

MODE. The printer is factory-set to emulate the HP PCL 6. The emulation mode can be changed by

following the procedures described in the Operation Guide contained as an electronic file in the

Kyocera Mita Digital Library CD-ROM supplied with the printer.

Notice

The information in this manual is subject to change without notification. Additional pages may be

inserted in future editions. The user is asked to excuse any technical inaccuracies or typographical

errors in the present edition.

No responsibility is assumed if accidents occur while the user is following the instructions in this

manual. No responsibility is assumed for defects in the printer's firmware (contents of its read-only

memory).

This manual, any copyrightable subject matter sold or provided with or in connection with the sale

of the page printer, are protected by copyright. All rights are reserved. Copying or other reproduc-

tion of all or part of this manual, any copyrightable subject matter without the prior written consent

of Kyocera Corporation is prohibited. Any copies made of all or part of this manual, any copyright-

able subject must contain the same copyright notice as the material from which the copying is done.

Table of Contents

STEP 1 Unpacking .......................................................................1

STEP 2 Positioning the Printer....................................................2

STEP 3 Installing the Toner Container........................................3

STEP 4 Connecting the Printer to the Computer .......................6

STEP 5 Connecting the Power Cord...........................................8

STEP 6 Adding Paper to the Paper Cassette and MP Tray........9

STEP 7 Using the Face-Up Output Tray....................................14

STEP 8 Printing a Status Page..................................................15

Unpacking

Carefully remove the printer and other items from the box. Check that nothing is miss-

ing against the list of shipped components below.

Shipped Components

Removing Shipping Material

Remove the tape on the rear side of the printer, and remove the two spacers and

printed notice from the paper cassette.

STEP

Printer

Power Cord

Toner Container (TK-17)

Installation Guide (this booklet) Kyocera Mita Digital Library CD-ROM

Cleaning Cloth

Ta p e Spacers

Printed Notice

Positioning the Printer

Make sure that the place of installation meets the following requirements:

Clearance

Be sure to secure enough space

around the printer. Prolonged

use without sufficient clearance

may cause heat to build up

within the printer, resulting in

fire.

Environment

Do not install the printer where temperature or humidity is outside the rec-

ommended range. Print quality may suffer and there will be an increased

chance of paper jams.

Places to Avoid

Avoid installing the printer in locations subject to:

• Direct drafts of hot or cold air

• Direct drafts from outside (Avoid locations near building entrances.)

• Sudden temperature or humidity changes

• Sources of high temperature, for example, near stoves or radiators

•Excessivedust

•Vibration

• Unstable surfaces and surfaces that are not level

• Ammonia or other harmful fumes (If you are planning to fumigate the room, or

make liberal use of insecticide, remove the printer first!)

• Excessive sunlight or humidity

• Lack of ventilation

• Lowairpressure,e.g.,elevationsgreaterthan2000meters(6500 feet)abovesea

level

Te m p e r a tu r e 10 to 32.5 °C (50 to 90.5 °F), ideally about 23 °C (73.4 °F)

Humidity 20 to 80 %, ideally 60 %

STEP

30 cm (11-13/16 inches)

40 cm

(15-3/4

inches)

25 cm

(9-7/8

inches)

50 cm

(19-11/16

inches)

25 cm (9-7/8

inches)

Installing the Toner Container

Before you can use the printer for the first time, you must set up the printer by installing

the toner container and interfacing with the computer.

1Open the printer top cover all the way.

2Confirm that the lock lever is in the

release (UNLOCK) position. If not, pull

it forward until it is in the release posi-

tion.

3Take the toner container from the bag.

Hold it with the protective seal (orange-

colored) facing up. Shake the toner con-

tainerhorizontallyatleast5times.This

ensures that the toner is evenly distrib-

uted inside.

STEP

4Carefully remove the protective seal.

5Install the toner container into the

printer.

6Push firmly on the top of the toner con-

tainer at the positions marked PUSH

HERE.

7Push the lock lever to the lock (LOCK)

position.

8Close the top cover.

To remove the toner container

Pull the lock lever #1 to the release

(UNLOCK) position, pull the lock lever

#2, then gently remove the toner con-

tainer.

LOCK

UNLOCK

LOCK

UNLOCK

Lock Lever #2

Lock Lever #1

Connecting the Printer to the Computer

There are variousways of connecting the printer to the computer, suchas through the

parallel interface connector, through the USB (Universal Serial Bus) interface connec-

tor, through the optional serial interface board kit (IB-10E)or through the optional net-

work interface board.

Printer Connections

Before performing this step, be sure to turn off both the printer and the com-

puter’s power switches and unplug the printer’s power plug from the power

outlet. Failure to do so may result in electrical shock.

The standard Centronics parallel interface connector and USB interface connec-

tor are located on the rear of the printer.

STEP

Printer (Rear)

Optional Serial Interface

Board kit (IB-10E)

Parallel Interface

Network

Optional Network

Interface Board

(DC 3.3V)

Serial Interface

Power Supply

USB

Interface

Parallel Interface Connection

1Plug one end of the printer cable (not

included) into the parallel interface con-

nector on the rear of the printer.

• Use a parallel printer cable

that complies with the

IEEE1284 standards.

• The printer will work best if it

is installed near the computer.

The connecting cable should

be shielded and not be longer

than 3 meters (10 feet).

2Close the clips on both sides to fix the

connector in place.

Plug the other end of the printer cable

into the computer’s Centronics parallel

interface connector.

USB (Universal Serial Bus) Interface Connection

1Plug one end of the USB cable on the

rear of the printer.

•Useacablethatcomplies

with Revision 1.1 of USB stan-

dard (a rectangular Type A

plug and a square Type B

plug).

• The connecting cable should

be shielded and not be longer

than 5 meters (16 feet).

2Plug the other end of the USB cableinto

the computer's USB interface connec-

tor.

To p r i n t e r

Clips

Printer Cable

To p r i n t e r

USB Cable

Connecting the Power Cord

This section describes the procedure for connecting the power cable and various

cautions.

Notes on Power Supply

• Install the printer near an AC wall outlet, preferably one that can be used for

the printer alone.

• Only use this printer with the supply voltage indicated on the serial number

label attached to the printer’s rear panel.

• If an extension cord is used, the total length of the power cord plus extension

should be 5 meters (16 feet) or less.

Power Requirements

To Connect the Power Cord

• Be sure the printer’s power switch is turned off.

• Only use the power cord supplied with the printer.

1Plug the power cord into the power cord

connector on the rear of the printer.

2Connect the other end of the power cord

into a power outlet.

Be sure to connect to a 3-wire

grounded power strip.

Voltage 120 V (U.S.A. and Canada), 220 to 240 V (European countries, and the

Asia-Pacific region), ±10 % at each voltage

Frequency 60 Hz (120 V) ±2 %, 50/60 Hz (220 to 240 V) ±2 %

Current capacity Max. 7.1 A at 120 V, or max. 3.8 A at 220 to 240 V

STEPSTEP

Power Cord

Connector

Power Cord

Otros manuales para Ecosys FS-1010

Tabla de contenidos

Otros manuales de Impresora de Kyocera Mita

Kyocera Mita

Kyocera Mita FS 8000C - Color Laser Printer Manual de usuario

Kyocera Mita

Kyocera Mita FS-1000 Manual de usuario

Kyocera Mita

Kyocera Mita Ecosys FS-6020 Manual de usuario

Kyocera Mita

Kyocera Mita FS-C5016N Manual de usuario

Kyocera Mita

Kyocera Mita DP-2800 Manual

Kyocera Mita

Kyocera Mita FS-C5016N Manual de usuario

Kyocera Mita

Kyocera Mita FS-1900N Manual de usuario

Kyocera Mita

Kyocera Mita KM-P4845w Manual de usuario

Kyocera Mita

Kyocera Mita WP31C Manual de usuario

Kyocera Mita

Kyocera Mita KM-P4850w Manual de usuario

Kyocera Mita

Kyocera Mita FS-8000CD Manual de usuario

Kyocera Mita

Kyocera Mita FS-6750 Manual de usuario

Kyocera Mita

Kyocera Mita Ecosys FS-1800N Manual de usuario

Kyocera Mita

Kyocera Mita Ecosys FS-1800+ Manual de usuario

Kyocera Mita

Kyocera Mita FS-9500DN Manual de usuario

Kyocera Mita

Kyocera Mita Ecosys FS-1800+ Manual de usuario

Kyocera Mita

Kyocera Mita Ecosys FS-6020 Manual de usuario

Kyocera Mita

Kyocera Mita FS-C5016N Manual de usuario

Kyocera Mita

Kyocera Mita FS-9100DN Manual de usuario

Kyocera Mita

Kyocera Mita KM-1505 Manual de usuario

Kyocera Mita

Kyocera Mita KM-P4845w Manual de usuario

Kyocera Mita

Kyocera Mita Ecosys FS-C8008DN Series Manual de usuario

Kyocera Mita

Kyocera Mita FS-1050 Manual de usuario

Kyocera Mita

Kyocera Mita KM-1500 Manual de usuario

Manuales populares de Impresora de otras marcas

Lexmark

Lexmark 1400 Series Manual

Canon

Canon i70 Series Manual de usuario

Evolis

Evolis Elypso Manual de usuario

Kyocera

Kyocera FS-9530DN Manual de usuario

Canon

Canon LASER SHOT LBP-1210 Manual de usuario

Samsung

Samsung BIXOLON SRP-350plusF Manual de usuario

Canon

Canon PIXMA PRO-1 Series Manual de usuario

Canon

Canon PIXMA G3560 Guía de configuración

Dell

Dell Color Laser Printer 2130cn Manual de usuario

Tektronix

Tektronix Phaser 840 Manual de usuario

Epson

Epson ET-7750 Instrucciones de funcionamiento

Canon

Canon CLBR 460ps Manual de usuario

Eltron

Eltron P210 Guide Manual de usuario

Ricoh

Ricoh MD-P1 Manual de usuario

Epson

Epson SC-F7100 series Manual de usuario

Epson

Epson Stylus C40UX Manual de usuario

Canon

Canon imagePASS-A2 Manual de usuario

Canon

Canon S820D Manual de usuario