KYMCO G-DINK 300i Manual de usuario

G-DINK 300i

By KWANG YANG Motor Co., Ltd.

1st Edition, ,Mar. 2012

unauthorized use without the written

permission of KWANG YANG Motor Co., Ltd.

is expressly prohibited.

T300-LHG7-A1

G-DINK 300i

PREFACE

This Service Manual describes the

technical features and servicing

procedures for the KYMCO

G-DINK 300i.

Section 1 contains the precautions for

all operations stated in this manual.

Read them carefully before any

operation is started.

Section 2 is the removal/installation

procedures for the frame covers

which are subject to

removal/installation frequency during

maintenance and servicing

operations.

Section 3 describes the inspection/

adjustment procedures, safety rules

and service information for each part,

starting from periodic maintenance.

Sections 5 to 12 give instructions for

disassembly, assembly and

adjustment of engine parts. Section

13 is the AFI system. Section 14 to 15

is the removal/ installation of chassis.

Section 16 to 19 states the testing

and measuring methods of electrical

equipment.

Most sections start with an assembly

or system illustration and

troubleshooting for the section. The

subsequent pages give detailed

procedures for the section.

KWANG YANG MOTOR CO., LTD.

QUALITY TECHNOLOGY DEPT.

EDUCATION SECTION

TABLE OF CONTENTS

GENERAL INFORMATION 1

EXHAUST MUFFLER/FRAME

COVERS 2

INSPECTION/ADJUSTMENT 3

LUBRICATION SYSTEM 4

ENGINE REMOVAL/INSTALLATION 5

CYLINDER HEAD/VALVES 6

CYLINDER/PISTON 7

DRIVE AND DRIVEN

PULLEYS/V-BELT 8

FINAL REDUCTION 9

A.C. GENERATOR/STARTER

CLUTCH 10

CRANKCASE/CRANKSHAFT 11

COOLING SYSTEM 12

FUEL INJECTION SYSTEM 13

STEERING HANDLEBAR/FRONT

WHEEL/FRONT BRAKE/FRONT

SHOCK ABSORBER/FRONT FORK

REAR BRAKE/REAR FORK/REAR

WHEEL/REAR SHOCK ABSORBER` 15

BATTERY/CHARGING SYSTEM 16

IGNITION SYSTEM 17

STARTING SYSTEM 18

LIGHTS SWITCHES / FUEL PUMP 19

The information and contents

included in this manual may be

different from the motorcycle in case

specifications are changed.

CHASSIS ELE

TRI

EQUIPMENT

ENGINE

1. GENERAL INFORMATION

1-0

G-DINK 300i

________________________________________________________________________________

GENERAL INFORMATION

________________________________________________________________________________

SERIAL NUMBER------------------------------------------------------------------------------------1-1

SPECIFICATION -------------------------------------------------------------------------------------1-2

SERVICE PRECAUTIONS-------------------------------------------------------------------------1-5

TORQUE VALUES-----------------------------------------------------------------------------------1-9

SPECIAL TOOLS----------------------------------------------------------------------------------- 1-11

LUBRICATION POINTS -------------------------------------------------------------------------- 1-12

CABLE & HARNESS ROUTING------------------------------------------------------------------- 1-14

TROUBLESHOOTING ---------------------------------------------------------------------------- 1-15

1. GENERAL INFORMATION

1-1

G-DINK 300i

Identification Numbers Record

1. GENERAL INFORMATION

1-2

G-DINK 300i

SPECIFICATIONS

Name G-DINK 300i

Model No. SH60AA

Overall length 2090 mm

Overall width 770 mm

Overall height 1360 mm

Wheel base 1450 mm

Engine type 4strokeO.H.C.

Displacement 270.6 cc

Fuel Used 92# nonleaded

gasoline above

Front wheel 61

Rear wheel 99

Curb weight

(kg) Total 160

Front wheel 105

Rear wheel 228

Max. weight

capacity (kg) Total 333

Ground clearance (mm) 140

Braking distance (m) 7.9m / 40 km/hr

Min. turning radius (mm) 2350

Engine part

Starting system Starting motor

Type Gasoline 4-cycle

Cylinder arrangement Single cylinder

Combustion chamber type Semi-sphere

Valve arrangement O.H.C.-4V

Bore x stroke (mm) φ72.7 * 65.2

Compression ratio 10.6:1

Compression pressure

(kg/cm²) 15

Max. output (ps/rpm) 22.8 /8000

Max. torque (kg-m/rpm) 22.5 / 6500

Open 9° BTDC

Intake Timing Close 36° BTDC

Open 42° BTDC

Exhaust

Timing Close 7° BTDC

Intake 0.10

Valve

clearance Exhaust 0.10

Idle speed (rpm) 1600±100 rpm

Cooling Type Liquid cooling

Lubrication type Forced pressure &

wet sump

Oil pump type Inner/outer rotor

Oil filter type Full-flow filtration

Oil capacity 1.1 liter

Exchanging capacity 0.9 liter

Fi injection system

Air cleaner type & No Paper element, wet

Fuel capacity 9 liters

Brand Keihin

Throttle Body Butterfly type

Venturi diameter (mm) 32

Fuel pump pressure 3 bar

Electrical system

Ignition type ECU

Ignition timing 9°BTDC / idle

36° / 6500min

Spark plug DPR6EA

Spark plug gap 0.9mm

Battery Capacity 12V10AH

Transmission system

Clutch type Dry multi-disc

Transmission type CVT

Operation type Auto centrifugal

Reduction gear type Two-stage reduction

1st 0.72 ~ 2.24

Reduction ratio 2nd 7.222

Moving device

Tire type Tubeless

Front wheel 120/70-13

Tire spec. Rear wheel 140/70-12

Front wheel 1.75

Tire pressure

(kg/cm²) Rear wheel 2.0

Wheel material Aluminium

Left 40°

Turning angle Right 40°

Front Disk brake

Brake type Rear Disk brake

Damping Device

Front Telescope

Suspension

type Rear Swing arm

Front 95 mmShock absorber

stroke Rear 90 mm

1. GENERAL INFORMATION

1-3

G-DINK 300i

SERVICE PRECAUTIONS

Make sure to install new gaskets, O-rings,

circlips, cotter pins, etc. when

reassembling.

When tightening bolts or nuts, begin with

larger-diameter to smaller ones at several

times, and tighten to the specified torque

diagonally.

Use genuine parts and lubricants.

When servicing the motorcycle, be sure to

use special tools for removal and

installation.

After disassembly, clean removed parts.

Lubricate sliding surfaces with engine oil

before reassembly.

Apply or add designated greases and

lubricants to the specified lubrication

points.

When two persons work together, pay

attention to the mutual working safety.

Disconnect the battery negative (-) terminal

before operation.

When using a spanner or other tools,

make sure not to damage the motorcycle

surface.

After operation, check all connecting points,

fasteners, and lines for proper connection

and installation.

When connecting the battery, the positive

(+) terminal must be connected first.

After connection, apply grease to the

battery terminals.

Terminal caps shall be installed securely.

If the fuse is burned out, find the cause

and repair it. Replace it with a new one

according to the specified capacity.

1. GENERAL INFORMATION

1-4

G-DINK 300i

After operation, terminal caps shall be

installed securely.

When taking out the connector, the lock on

the connector shall be released before

operation.

Hold the connector body when connecting

or disconnecting it.

Do not pull the connector wire.

Check if any connector terminal is bending,

protruding or loose.

The connector shall be inserted

completely.

If the double connector has a lock, lock

it at the correct position.

Check if there is any loose wire.

Before connecting a terminal, check for

damaged terminal cover or loose negative

terminal.

Check the double connector cover for

proper coverage and installation.

Insert the terminal completely.

Check the terminal cover for proper

coverage.

Do not make the terminal cover opening

face up.

Secure wire harnesses to the frame with

their respective wire bands at the

designated locations.

Tighten the bands so that only the

insulated surfaces contact the wire

harnesses.

After clamping, check each wire to make

sure it is secure.

Confirm

Capacity

1. GENERAL INFORMATION

1-5

G-DINK 300i

Do not squeeze wires against the weld or

its clamp.

After clamping, check each harness to

make sure that it is not interfering with any

moving or sliding parts.

When fixing the wire harnesses, do not

make it contact the parts that will generate

high heat.

Route wire harnesses to avoid sharp

edges or corners. Avoid the projected

ends of bolts and screws.

Route wire harnesses passing through the

side of bolts and screws. Avoid the

projected ends of bolts and screws.

Route harnesses so they are neither

pulled tight nor have excessive slack.

Protect wires and harnesses with electrical

tape or tube if they contact a sharp edge or

corner.

When rubber protector cover is used to

protect the wire harnesses, it shall be

installed securely.

Do not break the sheath of wire.

If a wire or harness is with a broken sheath,

repair by wrapping it with protective tape or

replace it.

When installing other parts, do not press or

squeeze the wires.

After routing, check that the wire

harnesses are not twisted or kinked.

Do not pull

too tight！

No Contact

Do not press or

squeeze the wire

1. GENERAL INFORMATION

1-6

G-DINK 300i

Wire harnesses routed along with

handlebar should not be pulled tight, have

excessive slack or interfere with adjacent

or surrounding parts in all steering

positions.

When a testing device is used, make sure

to understand the operating methods

thoroughly and operate according to the

operating instructions.

Be careful not to drop any parts.

When rust is found on a terminal, remove

the rust with sand paper or equivalent

before connecting.

Do you understand

the instrument？

Remove Rust！

1. GENERAL INFORMATION

1-7

G-DINK 300i

Symbols:

The following symbols represent the

servicing methods and cautions included in

this service manual.

: Apply engine oil to the

specified points. (Use

designated engine oil for

lubrication.)

: Apply grease for lubrication.

: Transmission Gear Oil (90#)

: Use special tool.

:Caution

:Warning

Special

Engine Oil

Grease

Gear Oil

＊

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Scooter de KYMCO

KYMCO

KYMCO Yager 200i Manual de usuario

KYMCO

KYMCO Bet&Win Nota de publicación

KYMCO

KYMCO Downtown 125i Manual de usuario

KYMCO

KYMCO PEOPLE 125 Manual de usuario

KYMCO

KYMCO 50 LIKE 2T Manual de usuario

KYMCO

KYMCO ZX Manual de usuario

KYMCO

KYMCO Mini LS Manual de usuario

KYMCO

KYMCO Maxi XLS Manual de usuario

KYMCO

KYMCO K-XCT 300i Manual de usuario

KYMCO

KYMCO Agility City 50 Nota de publicación

KYMCO

KYMCO PEOPLE S 125 Manual de usuario

KYMCO

KYMCO Agility RS 50 Manual de usuario

KYMCO

KYMCO Like 200i Manual de usuario

KYMCO

KYMCO Super 9 50 Manual de usuario

KYMCO

KYMCO PEOPLE S 125 Manual de usuario

KYMCO

KYMCO 50 AGILITY CITY 4T Manual de usuario

KYMCO

KYMCO 125 DINK - Manual de usuario

KYMCO

KYMCO Aglity 50 Manual de usuario

KYMCO

KYMCO Sento 50 Manual de usuario

KYMCO

KYMCO PEOPLE S 50 2005 Manual de usuario

KYMCO

KYMCO XCITING 500 Manual de usuario

KYMCO

KYMCO LIKE 150i Manual de usuario

KYMCO

KYMCO Compagno 110i Manual de usuario

KYMCO

KYMCO 125 DINK - Manual de usuario

Manuales populares de Scooter de otras marcas

TEKTRO

TEKTRO CHEETAH Manual de usuario

Douglas

Douglas Vespa Sprint Guía de instalación

PLAYTIVE

PLAYTIVE AS-2448 Manual de usuario

Ebinger

Ebinger DONKEY XL Manual de usuario

Flyer

Flyer Mountain Guía del usuario

BackCountry eBikes

BackCountry eBikes Storm Manual de usuario

equipmed

equipmed FreeRoam II Manual de usuario

Yoto

Yoto Lion Manual de usuario

WESTHILL BIKES

WESTHILL BIKES LINK Manual de usuario

BAnff

BAnff eProdigy series Manual de usuario

Winther

Winther 475 Manual de usuario

Jetson

Jetson JBZL17 Manual de usuario

First Choice Mobility

First Choice Mobility Roma Medical Corella S741 Manual de usuario

Carrera

Carrera impel Manual de usuario

Afikim

Afikim Superlight SL-3 Manual de usuario

CareCo

CareCo ZOOM Manual de usuario

Douglas

Douglas Vespa G.S. Manual de usuario

Gazelle

Gazelle with BOSCH System Manual de usuario