Kwikset Smartcode 914 Instrucciones de funcionamiento
©2015 Spectrum Brands, Inc.
Programming and Troubleshooting Guide
Mastercode 2
Troubleshooting: Installation 8
Troubleshooting: Door Jamming and Door Handing 9
Troubleshooting: Keypad 13
Troubleshooting: Smart Home Systems 14
Troubleshooting: Battery 16
Battery FAQ 17
©2015 Spectrum Brands, Inc.
61883 / 01
1 / 17
Technical Support
1-866-863-6584
www.kwikset.com
1
3
2
4
5
6
7
©2015 Spectrum Brands, Inc.
Mastercode
Programming timeout: If no button is pressed for ve seconds, the system will time out
(indicated by three beeps and a red ashing keypad), and you will need to restart the procedure.
1. Keep door open. Press and HOLD the Program button until the keypad
ashes green (about 5 seconds).
2. Enter new Mastercode.
3. Press Lock button once.
4. Re-enter Mastercode.
5. Press Lock button once.
If programming is successful, the keypad will flash green once with
one beep.
If programming is unsuccessful, the keypad will ash red three times
with three beeps. Make sure the Mastercode has not already been
programmed. Attempt the procedure again, making sure to enter the
same new Mastercode in step 2 and 4.
6. Make sure switch #3 is on, and press the Program button once. If you
hear three beeps and see the keypad ash green, the Mastercode is
enabled.
Note: The lock will time out after ve seconds.
Using a Mastercode is an optional, added-security measure. It is not enabled by default. A Mastercode is
used to add and delete user codes, but it cannot unlock the door (unless the same code is programmed
as a user code, though this is not recommended). The Mastercode must be 4-8 digits.
©2015 Spectrum Brands, Inc.
61883 / 01
2 / 17
Technical Support
1-866-863-6584
www.kwikset.com
1
A
B
About the Mastercode
Enabling and Setting the Mastercode
©2015 Spectrum Brands, Inc.
1. Keep door open. Press the Program button once. The keypad will ash
green and you will hear three beeps.
2. Enter Mastercode.
3. Press Lock button once.
4. Enter new user code.
5. Press Lock button once.
If programming is successful, the keypad will flash green once with
one beep.
If programming is unsuccessful, the keypad will ash red three times with
three beeps. Make sure the user code is not a duplicate and that it is
between 4 and 8 digits during your next attempt. Make sure the lock has
room for an additional code. If all user codes are lled, delete a code to make
room for this one. Make sure to enter a valid Mastercode in step 2.
6. While the door is open and locked, test the user code to make
sure it unlocks the door.
The procedure for adding user codes is different when the Mastercode is enabled. For instuctions on how
to add user codes when the Mastercode is disabled, see the Installation and User Guide that came with
your lock.
©2015 Spectrum Brands, Inc.
61883 / 01
3 / 17
Technical Support
1-866-863-6584
www.kwikset.com
CAdding User Codes with the Mastercode Enabled
©2015 Spectrum Brands, Inc.
1. Keep door open. Press the Program button once. The keypad will ash
green and you will hear three beeps.
2. Press Lock button once.
3. Enter Mastercode.
4. Press Lock button once.
5. Enter user code to be deleted.
6. Press Lock button once.
7. Re-enter user code to be deleted.
8. Press Lock button once.
Procedure continued on next page
©2015 Spectrum Brands, Inc.
61883 / 01
4 / 17
Technical Support
1-866-863-6584
www.kwikset.com
DDeleting a Single User Code with the Mastercode Enabled
©2015 Spectrum Brands, Inc.
If programming is successful, the keypad will flash green once with
one beep.
If programming is unsuccessful, the keypad will ash red three times with
three beeps. Make sure to enter the same valid code in steps 5 and 7.
Make sure to enter a valid Mastercode in step 3.
9. While the door is open and locked, test the user code to make sure it
no longer unlocks the door.
1. Keep door open. Press the Program button once. The keypad will ash
green and you will hear three beeps.
2. Press Lock button once.
3. Enter Mastercode.
4. Press Lock button once.
5. Press “9” six times.
6. Press Lock button once.
Procedure continued on next page
©2015 Spectrum Brands, Inc.
61883 / 01
5 / 17
Technical Support
1-866-863-6584
www.kwikset.com
EDeleting All User Codes with the Mastercode Enabled
©2015 Spectrum Brands, Inc.
7. Press “9” six times.
8. Press Lock button once.
If programming is successful, the keypad will flash green once with
one beep.
If programming is unsuccessful, the keypad will ash red three times with
three beeps. Make sure to enter a valid Mastercode in step 3 during your
next attempt.
9. Press the Lock button while the door is open and unlocked. If
the latch bolt does not extend to lock, then all codes have been
successfully deleted.
©2015 Spectrum Brands, Inc.
61883 / 01
6 / 17
Technical Support
1-866-863-6584
www.kwikset.com
©2015 Spectrum Brands, Inc.
1. Keep door open. Press and HOLD the Program button until the keypad
ashes green (about 5 seconds).
2. Press Lock button once.
3. Enter Mastercode.
4. Press Lock button once.
5. Re-enter Mastercode.
6. Press Lock button once.
If programming is successful, the keypad will flash green once with
one beep.
If programming is unsuccessful, the keypad will ash red three times with
three beeps. Make sure the Mastercode has been enabled before trying
to disable it. Attempt this procedure again, making sure to enter the same
Mastercode in steps 3 and 5.
7. Make sure switch #3 is on, and then press the Program button once.
If you don’t immediately hear three beeps and see the keypad ash
green, the Mastercode is disabled.
Note: The lock will time out after ve seconds.
©2015 Spectrum Brands, Inc.
61883 / 01
7 / 17
Technical Support
1-866-863-6584
www.kwikset.com
FDisabling and Deleting the Mastercode
©2015 Spectrum Brands, Inc.
Troubleshooting: Installation
If you encounter any of the problems above, the deadbolt latch may be
installed upside down. Remove the interior assembly, mounting plate,
and exterior assembly from the door, and look at the latch inside the
door hole.
If the word “UP” is upside down and at the bottom of the latch, the latch
is installed incorrectly.
Reinstall the latch, making sure the word “UP” faces upward.
©2015 Spectrum Brands, Inc.
61883 / 01
8 / 17
Technical Support
1-866-863-6584
www.kwikset.com
2
A
B
C
The interior mounting screws are dicult to tighten.
The interior and exterior assembly won’t mount parallel to the door edge.
The interior assembly does not fit on the mounting plate.
©2015 Spectrum Brands, Inc.
Troubleshooting: Door Jamming and Door Handing
The door handing process was not executed
during installation.
Perform the door handing process in the Installation Guide.
The hole in the door is misaligned.
Disassemble the lock, and reinstall it without the adapter ring on the
exterior side of the door.
The wrong deadbolt latch is installed.
SmartCode deadbolts require a tapered latch bolt for ease of operation.
If the latch being used is from an older lock, it will likely not have a
tapered latch bolt. Remove the lock from the door, including the old
latch. Replace with the new tapered latch that came with the lock and
reinstall the lock.
The deadbolt latch and strike are misaligned,
causing the latch to bind.
Adjust the tab of the lower strike (for your knob or lever) to help align the
upper latch and strike so that the latch bolt enters the strike when the
door is locked.
The lower latch and lower strike (for your knob
or lever) are misaligned, putting too much
load on the deadbolt latch.
As a test, rotate the turnpiece on the deadbolt so the latch is retracted
(unlocked), and close the door. If you have to push, pull or lift the door to
get it to close, adjust the position of the lower strike.
©2015 Spectrum Brands, Inc.
61883 / 01
9 / 17
Technical Support
1-866-863-6584
www.kwikset.com
3
A
B
The lock jams and the turnpiece does not rotate smoothly.
The lock beeps, the keypad flashes red, and the door cannot lock.
©2015 Spectrum Brands, Inc.
The hole in the door frame for the latch bolt is
not drilled deep enough.
Make sure the hole in the door frame is drilled at least 1” (25 mm) deep.
The mounting plate is placing tension on the
torque blade.
Attempt to lock and unlock the door with the key. If it is unable to rotate,
remove the interior assembly from the mounting plate. Test the key
again. If it is still unable to rotate, loosen the screws on the mounting
plate and reposition the plate so there is no tension on the cylinder
torque blade. Make sure the latch bolt can operate smoothly with the key
and reinstall the interior assembly.
The clutch is disengaged.
Remove the battery pack. Remove the interior assembly from the
door. Verify that the lock can be operated smoothly with the key while
the interior is removed. Attempt to rotate the turnpiece on the interior
assembly to the vertical position. If it cannot rotate to the vertical position,
the clutch has become disengaged.
Place the battery cover onto the interior assembly, making sure to align
the turnpiece with the shaft. Rotate the turnpiece 180° clockwise (you
will need to use force when rotating the turnpiece, and you will hear it
click). This will re-engage the clutch.
180°
Align the turnpiece with the torque blade and reinstall the interior
assembly on the door.
©2015 Spectrum Brands, Inc.
61883 / 01
10 / 17
Technical Support
1-866-863-6584
www.kwikset.com
Otros manuales para Smartcode 914
8
Otros manuales de Cerrar de Kwikset
Kwikset
Kwikset Smartcode 910 Manual de usuario
Kwikset
Kwikset HALO TOUCH 959TRL Manual de instalación y funcionamiento
Kwikset
Kwikset SMARTCODE 916 Manual de usuario
Kwikset
Kwikset OBSIDIAN Manual de usuario
Kwikset
Kwikset 905 Manual de usuario
Kwikset
Kwikset Smartcode 914 Manual de usuario
Kwikset
Kwikset Halo Touch Manual de usuario
Kwikset
Kwikset 48334/01 Manual de usuario
Kwikset
Kwikset 985 Manual de usuario
Kwikset
Kwikset SmartCode 913 Manual de usuario
Kwikset
Kwikset HALO Manual de usuario
Kwikset
Kwikset Henley 300HYL 15 Manual de usuario
Kwikset
Kwikset SMARTCODE 916 Manual de usuario
Kwikset
Kwikset SmartKey Series Manual de usuario
Kwikset
Kwikset SmartCode Series Instrucciones de montaje
Kwikset
Kwikset Smartcode 915 Manual de usuario
Kwikset
Kwikset Smartcode 914 Manual de usuario
Kwikset
Kwikset SMARTCODE 915 Manual de usuario
Kwikset
Kwikset Powerbolt 240 Manual de usuario
Kwikset
Kwikset SmartCode 913 Manual de usuario
