Kwikset Smartcode 888 Manual de usuario

Programming and Troubleshooting Guide

Mastercode 2

Troubleshooting: Installation 8

Troubleshooting: Door Jamming and Door Handing 10

Troubleshooting: Keypad 14

Troubleshooting: Smart Home Systems 15

Troubleshooting: Battery 17

Battery FAQ 18

61899 Rev 01

1 / 18

Technical Support

1-866-863-6584

www.kwikset.com

Mastercode

Programming timeout: If no button is pressed for ve seconds, the system will time out

(indicated by three beeps and a red ashing lock button), and you will need to restart the procedure.

1. Make sure the audio setting on the lock is turned on / not muted.

2. Keep door open. Press and HOLD the Program button until the lock

button ashes green (about 5 seconds).

3. Enter new Mastercode.

4. Press Lock button once.

5. Re-enter Mastercode.

6. Press Lock button once.

If programming is successful, the lock button will flash green once

with one long beep.

If programming is unsuccessful, the lock button will ash red three

times with three beeps. Make sure the Mastercode has not already been

programmed. Attempt the procedure again, making sure to enter the

same new Mastercode in step 2 and 4.

7. Press the Program button once. If you hear three beeps and see the

lock button ash green, the Mastercode is enabled. Note: The lock will

time out after ve seconds.

Using a Mastercode is an optional, added-security measure. It is not enabled by default. A Mastercode is

used to add and delete user codes, but it cannot unlock the door (unless the same code is programmed

as a user code, though this is not recommended). The Mastercode must be 4-8 digits.

61899 Rev 01

2 / 18

Technical Support

1-866-863-6584

www.kwikset.com

About the Mastercode

Enabling and Setting the Mastercode

1. Keep door open. Press the Program button once. The lock button will

ash green and you will hear three beeps.

2. Enter Mastercode.

3. Press Lock button once.

4. Enter new user code.

5. Press Lock button once.

If programming is successful, the lock button will flash green once

with one long beep.

If programming is unsuccessful, the lock button will ash red three times

with three beeps. Make sure the user code is not a duplicate and that it is

between 4 and 8 digits during your next attempt. Make sure the lock has

room for an additional code. If all user codes are lled, delete a code to make

room for this one. Make sure to enter a valid Mastercode in step 2.

6. While the door is open and locked, test the user code to make

sure it unlocks the door.

The procedure for adding user codes is different when the Mastercode is enabled. For instuctions on how

to add user codes when the Mastercode is disabled, see the Installation and User Guide that came with

your lock.

Mastercode (cont.)

61899 Rev 01

3 / 18

Technical Support

1-866-863-6584

www.kwikset.com

CAdding User Codes with the Mastercode Enabled

1. Keep door open. Press the Program button once. The lock button will

ash green and you will hear three beeps.

2. Press Lock button once.

3. Enter Mastercode.

4. Press Lock button once.

5. Enter user code to be deleted.

6. Press Lock button once.

7. Re-enter user code to be deleted.

8. Press Lock button once.

Procedure continued on next page

Mastercode (cont.)

61899 Rev 01

4 / 18

Technical Support

1-866-863-6584

www.kwikset.com

DDeleting a Single User Code with the Mastercode Enabled

If programming is successful, the lock button will flash green once

with one long beep.

If programming is unsuccessful, the lock button will ash red three times

with three beeps. Make sure to enter the same valid code in steps 5 and

7. Make sure to enter a valid Mastercode in step 3.

9. While the door is open and locked, test the user code to make sure it

no longer unlocks the door.

1. Keep door open. Press the Program button once. The lock button will

ash green and you will hear three beeps.

2. Press Lock button once.

3. Enter Mastercode.

4. Press Lock button once.

5. Press “9-0” six times.

6. Press Lock button once.

Procedure continued on next page

Mastercode (cont.)

61899 Rev 01

5 / 18

Technical Support

1-866-863-6584

www.kwikset.com

EDeleting All User Codes with the Mastercode Enabled

7. Press “9-0” six times.

8. Press Lock button once.

If programming is successful, the lock button will flash green once

with one long beep.

If programming is unsuccessful, the lock button will ash red three times

with three beeps. Make sure to enter a valid Mastercode in step 3 during

your next attempt.

9. Press the Lock button while the door is open and unlocked. If

the latch bolt does not extend to lock, then all codes have been

successfully deleted.

Mastercode (cont.)

61899 Rev 01

6 / 18

Technical Support

1-866-863-6584

www.kwikset.com

1. Make sure the audio setting on the lock is turned on / not muted.

2. Keep door open. Press and HOLD the Program button until the lock

button ashes green (about 5 seconds).

3. Press Lock button once.

4. Enter Mastercode.

5. Press Lock button once.

6. Re-enter Mastercode.

7. Press Lock button once.

If disabling is successful, the lock button will flash green once with

one beep.

If programming is unsuccessful, the lock button will ash red three times

with three beeps. Make sure the Mastercode has been enabled before

trying to disable it. Attempt this procedure again, making sure to enter

the same Mastercode in steps 3 and 5.

8. Press the Program button once. If you don’t immediately hear three

beeps and see the lock button ash green, the Mastercode is disabled.

Note: The lock will time out after ve seconds.

Mastercode (cont.)

61899 Rev 01

7 / 18

Technical Support

1-866-863-6584

www.kwikset.com

FDisabling and Deleting the Mastercode

Troubleshooting: Installation

If you encounter any of the problems above, the deadbolt latch may be

installed upside down. Remove the interior assembly, mounting plate,

and exterior assembly from the door, and look at the latch inside the

door hole.

If the word “UP” is upside down and at the bottom of the latch, the latch

is installed incorrectly.

Reinstall the latch, making sure the word “UP” faces upward.

Other solutions may include:

1. Loosen the mounting screws and make sure they go in straight without

cross-threading.

2. Loosen the mounting screws and latch screws and reinstall the

mounting screws rst before tigthening the latch screws.

3. Chisel out the bore hole opposite side of the latch if the latch cannot

be centered.

61899 Rev 01

8 / 18

Technical Support

1-866-863-6584

www.kwikset.com

The interior mounting screws are dicult to tighten.

The interior and exterior assembly won’t mount parallel to the door edge.

The interior assembly does not ﬁt on the mounting plate.

The turnpiece was rotated past its normal range.

Troubleshooting: Installation (cont.)

If the interior assembly is not installed on the door, place the interior

cover over it. Align the hole in the turnpiece with the shaft.

The turnpiece should be able to rotate to the vertical position.

The triangular turnshaft should point up as shown.

If it cannot rotate to the vertical position, use force to rotate the

turnpiece clockwise until it clicks. The turnpiece should now be able to

rotate to the vertical position.

If the interior assembly is installed on the door, and the turnpiece cannot

rotate to a vertical position, perform the door handing process. See the

Installation and User Guide for more details.

If manual door handing still does not work, contact Customer Service.

Vertical

61899 Rev 01

9 / 18

Technical Support

1-866-863-6584

www.kwikset.com

DThe turnpiece is upside down, or it cannot rotate to a vertical position.

Troubleshooting: Door Jamming and Door Handing

The door handing process was not

executed during installation.

Perform the door handing process in the Installation Guide.

The latch cam is hitting the bore hole

Remove the mounting plate and exterior assembly (A). Use a

screwdriver to turn the latch (B). If it hits the bore hole, use a

chisel to correct the bore hole (C).

The wrong deadbolt latch is installed.

SmartCode deadbolts require a tapered latch bolt for ease of operation.

If the latch being used is from an older lock, it will likely not have a

tapered latch bolt. Remove the lock from the door, including the old

latch. Replace with the new tapered latch that came with the lock and

reinstall the lock.

61899 Rev 01

10 / 18

Technical Support

1-866-863-6584

www.kwikset.com

The lock jams and the turnpiece does not rotate smoothly.

The lock beeps, the lock button ﬂashes red, and the door cannot lock.

The deadbolt latch and strike are misaligned,

causing the latch to bind.

Adjust the tab of the lower strike (for your knob or lever) to help align the

upper latch and strike so that the upper latch bolt enters the strike when

the door is locked. If needed, call Kwikset to order a warped door kit.

Otros manuales para Smartcode 888

Tabla de contenidos

Otros manuales de Cerrar de Kwikset

Kwikset

Kwikset 48334/01 Manual de usuario

Kwikset

Kwikset Kevo Guía de instalación

Kwikset

Kwikset OBSIDIAN Instrucciones de funcionamiento

Kwikset

Kwikset 905 Manual de usuario

Kwikset

Kwikset Smartcode 914 Manual de usuario

Kwikset

Kwikset 264 Manual de usuario

Kwikset

Kwikset HomeConnect 620 Manual de usuario

Kwikset

Kwikset Powerbolt 250 Manual de usuario

Kwikset

Kwikset HomeConnect 620 Manual de usuario

Kwikset

Kwikset Smartcode 914 Instrucciones de funcionamiento

Kwikset

Kwikset 24896/04 Manual de usuario

Kwikset

Kwikset Smartcode 910 Manual de usuario

Kwikset

Kwikset 985 Manual de usuario

Kwikset

Kwikset SmartCode 913 Manual de usuario

Kwikset

Kwikset HomeConnect 620 Manual de instrucciones

Kwikset

Kwikset Smartcode 914 Manual de usuario

Kwikset

Kwikset SmartCode 913 Manual de usuario

Kwikset

Kwikset SmartKey Series Manual de usuario

Kwikset

Kwikset Signature Series Austin 788AUL LH 11P Manual de usuario

Kwikset

Kwikset SMARTCODE 916 Manual de usuario

Kwikset

Kwikset Convert 914C Z-wave plus Manual de usuario

Kwikset

Kwikset SmartCode 909 Manual de usuario

Kwikset

Kwikset Deadbolt Series Manual de usuario

Kwikset

Kwikset SmartCode 913 Manual de usuario

Manuales populares de Cerrar de otras marcas

Magic

Magic 105 Manual de usuario

Gantner

Gantner GAT NET.Lock 7020 System Guía rápida

Wittkopp

Wittkopp Insys 7202 Manual de usuario

Dorma

Dorma Studio Classic Manual de usuario

Securam

Securam ECSL-601 Manual de usuario

Sudhaus

Sudhaus 3003 Manual de usuario

Safety 1st

Safety 1st 48517 Manual de usuario

Pado

Pado FDS-10 Manual de usuario

Esco

Esco systeQ Series Manual de usuario

COMPX

COMPX National D8951 Manual de usuario

secureo

secureo Key Box Manual de usuario

Stock Loks

Stock Loks C8713 Manual de usuario

COMPX

COMPX 1T-058 Manual del propietario

Auslock

Auslock T11 Manual de usuario

ELCOM

ELCOM 7205 Manual de usuario

Stealth SAFES

Stealth SAFES ShadowVault Manual de usuario

Knox

Knox KeySecure 5 Manual de usuario

Metra Electronics

Metra Electronics Door Access Terminal Combo Manual de usuario