KVH Industries TracVision A9 Manual de usuario

KVH and TracVision are registered trademarks of KVH Industries, Inc. All other trademarks are property of their respective companies.

The information in this document is subject to change without notice. No company shall be liable for errors contained herein.

TracVision A9 Antenna

Reshipping Instructions

Technical Support

If you need technical assistance, please contact KVH Technical Support:

Phone: +1 401 847-3327

Email: [email protected]

(Mon.-Fri., 9 am-6 pm; Sat., 9 am-2 pm ET, -5 GMT)

The following pages explain how to prepare a

TracVision®A9 antenna for reshipping.

Tools Required

This procedure requires the following tools:

• Phillips screwdrivers

• #2 Phillips torque screwdriver set to 21 in.-lbs

•1/4"driver

• 1/4" hex bit, if necessary

• 5/32" torque hex driver set to 21 in-lbs

Step 1 - Remove the Mounting Brackets

a. Power off and disconnect power from the

TV-Hub to remove power from the antenna.

b. Disconnect the RF cable from the antenna.

c. Remove the antenna from the vehicle and bring it

to a workbench suitable for service.

Important!

Be sure to install the tie-wrap shipping restraints

and pack the antenna in its original packaging, as

explained in these instructions, to ensure a safe

shipment. Without the restraints, the antenna will

become damaged. Shipping damage will not be

covered under KVH’s warranty policy.

CAUTION

To prevent injury, be sure to disconnect all power

from the antenna before proceeding. Power must

remain disconnected for the duration of this

procedure.

Figure 1: A9 Antenna

d. Disconnect the four mounting brackets from the

antenna by removing the two 1/4"-20 x 3/4" hex

socket screws at each mounting bracket (see

Figure 2). Save the mounting brackets and

hardware for later.

NOTE: The factory-installed bolts, in the base of the

antenna between the bracket holes, do not need to be

removed.

Step 2 - Remove the Trim Ring and Radome

a. Remove the sixteen #8-32 screws securing the

trim ring (see Figure 3). Carefully lift the trim

ring straight up until clear of the antenna

assembly and set it aside in a safe place.

b. Remove the four 1/4"-20 screws and washers

securing the radome to the baseplate (see

Figure 3). Set the radome aside with the trim

ring.

Step 3 - Attach the Shipping Restraints

Attach the six tie-wraps (supplied in kit) in the key

locations shown in Figure 4 and in detailed photos

on the following page (the photos show the original

factory-installed wire restraints).

Insert the tie-wraps from below, through the

appropriate holes in the antenna’s base, so that the

tie-wraps’ buckles will rest on the bottom of the

antenna. Be sure to pass the tie-wraps underneath

any cables, to prevent the tie-wraps and cables from

being pinched.

Important!

Always lift the antenna by the baseplate and never

by the radome or any portion of the internal

antenna assembly.

Important!

Rotate the antenna assembly by hand to line up the

holes in the assembly with the holes in the base (see

Figure 4).

Figure 2: Removing the Mounting Brackets

Factory-installed bolt

Bracket

1/4"-20 x 3/4" Hex Socket

Screws (with Nylok patch)

Figure 3: Removing the Trim Ring and Radome

Trim Ring

#8-32 Screw (x16)

Radome

1/4"-20 Screw

and Washer (x4)

Figure 4: Shipping Restraint Locations

Figure 5: Shipping Restraints #1 and #2

Figure 6: Shipping Restraint #3

Figure 7: Shipping Restraint #4

Figure 8: Shipping Restraint #5

Figure 9: Shipping Restraint #6

Step 4 - Reattach the Radome and Trim Ring

a. Inspect the inside of the antenna to make sure

you have not left any tools or debris inside.

b. Reinstall the radome onto the antenna, securing

it with the four 1/4"-20 screws and washers you

removed earlier. Then tighten the screws to

21 in.-lbs of torque (see Figure 10).

c. Reinstall the trim ring with the sixteen #8-32

screws you removed earlier. Then tighten the

screws to 21 in.-lbs of torque (see Figure 10).

Step 5 - Pack the Antenna

Pack the antenna in its original shipping box using

the original packaging materials (if you don’t have the

original box, please request one from KVH Technical

Support). The “FWD” indicator on all four corner

inserts should point in the same direction, toward

the forward end of the antenna, opposite the cable

connector.

The antenna is now ready for shipping!

Figure 10: Reattach the Trim Ring and Radome

Trim Ring

#8-32 Screw (x16)

Radome

1/4"-20 Screw

and Washer (x4)

Figure 11: Forward Indicators Pointing Away From Cable Connector

Cable

Connector

Rear inserts

have flat end at

Forward indicator

Front inserts have

pointed end at

Forward indicator

Otros manuales de Antena de KVH Industries

KVH Industries

KVH Industries TracVision 6 Manual de usuario

KVH Industries

KVH Industries TracPhone V11IP Manual de usuario

KVH Industries

KVH Industries TracPhone V7-IP Manual de usuario

KVH Industries

KVH Industries SAILOR 4300 Guía rápida

KVH Industries

KVH Industries TracPhone V7-IP Manual de usuario

KVH Industries

KVH Industries 5616 Manual de usuario

KVH Industries

KVH Industries TracPhone V11 Manual de usuario

KVH Industries

KVH Industries TracVision A9 Manual de usuario

KVH Industries

KVH Industries TracVision R5SL Guía

KVH Industries

KVH Industries TracVision M7 Guía

KVH Industries

KVH Industries TracVision M9 Guía

KVH Industries

KVH Industries TracVision M5 Manual de usuario

KVH Industries

KVH Industries TracPhone V7 Guía

KVH Industries

KVH Industries TracVision HD7 LNB Guía

KVH Industries

KVH Industries TracPhone V11IP Manual de usuario

KVH Industries

KVH Industries TracVision R6 DX Manual de usuario

KVH Industries

KVH Industries TracPhone V3HTS Manual de usuario

KVH Industries

KVH Industries Ka Tri-Americas LNB Manual de usuario

KVH Industries

KVH Industries TracPhone V30 Instrucciones de instalación y funcionamiento

KVH Industries

KVH Industries TracPhone V3 HTS LNB Manual de usuario

KVH Industries

KVH Industries TracVision M9 Guía

KVH Industries

KVH Industries TracVision L3 Manual de usuario

KVH Industries

KVH Industries TracVision A7 Manual de usuario

KVH Industries

KVH Industries TracVision R5SL Manual de usuario

Manuales populares de Antena de otras marcas

Alfa Network

Alfa Network APA-L01 Manual de usuario

Naval

Naval PR-422CA Manual de usuario

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Manual de usuario

TERK Technologies

TERK Technologies TV44 Manual de usuario

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Manual de usuario

HP J8999A Manual de usuario

MobilSat

MobilSat MSP-S Manual de usuario

Steren

Steren ANT-UHF 13 Manual de usuario

Novatel

Novatel 600-G Manual de operación

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Manual de usuario

TRENDnet

TRENDnet TEW-AO12O Manual de usuario

Radio Shack

Radio Shack 15-1837 Manual de usuario

CommScope

CommScope CMAX-OMFX-43M-I53 Manual de usuario

Ramsey Electronics

Ramsey Electronics DAP25 Manual de usuario

COBHAM

COBHAM SAILOR 800 VSAT Manual de uso y cuidado

Trango Systems

Trango Systems AD900-9 Manual de usuario

Steren

Steren ANT-100 Manual de usuario

Proxim

Proxim 5054-PA-23 Manual de usuario