KVH Industries TracPhone V3 Manual de usuario

TracPhone®V3 Installation Checklist

Please complete to validate your installation

Installation Information

Vessel Name: ___________________________________ Customer Name: ___________________________________

Antenna Serial Number:___________________________ Installation Date: ___________________________________

Installing Technician: _____________________________ Installing Company: _________________________________

Company Address:_________________________________________________________________________________

City: __________________________________________ State/Province:_____________________________________

Postal/Zip Code:_________________________________ Country: __________________________________________

Phone Number: _________________________________ E-mail: ___________________________________________

Installation Quality Check

Antenna Unit

The antenna is mounted in a blockage-free area, with a clear view of the sky.

Location description: ________________________________________________________________________

The antenna is mounted away from other antennas and compasses and outside the beam path of radar(s).

The antenna is mounted on a ﬂat, level surface/pedestal capable of supporting the antenna’s weight of 25 lbs

(11.3 kg) under all environmental conditions.

RF radiation exposure was taken into consideration when choosing a mounting location.

The “Forward” arrow inside the baseplate is pointing towards the bow and is parallel to the vessel's centerline.

Both shipping restraints have been removed.

The cable access hole was sealed as necessary to prevent water from seeping into the vessel.

Anti-seize lubricant was applied to all four mounting bolts.

The four rubber feet are bottomed against the mounting surface and the foam seal surrounding the cable access

hole is fully compressed.

Belowdecks Equipment

All belowdecks equipment is installed in a dry location that provides good ventilation.

Location description: ________________________________________________________________________

The front panels of the control unit and modem are easily accessible to the user.

All cables are strain-relieved at the back of the modem and control unit using the supplied bracket(s).

If the customer has a wireless access point (WAP), it is placed in a location that provides good WiFi reception.

50-0138_C

KVH Industries, Inc. • 50 Enterprise Center • Middletown, RI 02842-5279 • U.S.A. • Tel: +1 401 847-3327 • Fax: +1 401 851-3823 • E-mail: satelliteservices@kvh.com

KVH Industries A/S • Kokkedal Industripark 2B • 2980 Kokkedal • Denmark • Tel: +45 45 160 180 • Fax: +45 45 160 181 • E-mail: airtime@kvh.dk

Continued on reverse...

Please fax or e-mail this form to the appropriate KVH Airtime Services Department:

N. America, S. America, Australia Europe, Middle East, Asia, Africa

+1 401 851-3823 +45 45 160 181

[email protected] [email protected]

Installation Quality Check (continued)

Wiring

Appropriate 75WRF cables connect the antenna to the modem (RX, TX). These cables were terminated at both

ends with the correct “F” connectors using the proper tools, exactly to the manufacturer's speciﬁcations. The

center conductor pin at each end is 1/4" (5-7 mm) in length, measured from inside the nut to the tip.

Cable length: _______________________________ Cable type used: ______________________________

Connectors used: ___________________________

If LMR-400-75 or LMR-600-75 cables are used, the supplied RG-11 pigtail cables connect them to the antenna.

All RF cable connections above deck are protected against seawater and corrosion using DOW Corning #4 silicone

grease (inside the connectors) and silicone sealant or equivalent (outside the connectors).

RF cables are strain-relieved, protected from abrasion, and free of stress. A minimum 4.5" (11.5 cm) bend radius

[or 6" (15.3 cm) for LMR-600-75] is maintained throughout, and service loops are present where appropriate.

All RF cable connections were tightened to 20 inch-pounds of torque.

All wiring conforms to the system wiring diagram provided in the Installation Guide.

Straight-through (not crossover) Ethernet cables were used to connect the switch and MTA.

The customer's analog phone is connected to the PHONE 1 jack on the MTA. Nothing is connected to PHONE 2.

Power and Grounding

If the vessel is limited to two-phase, split-phase, or delta AC power, either (1) an isolation transformer was

installed to supply single-phase power to the antenna, or (2) the customer granted permission to run the antenna

system on two-phase power, which will cause a small amount of leakage current onto ship's ground.

The difference between the equipment's chassis ground and ship's ground measures < 25 volts.

The vessel's electrical system provides grounding according to commercial marine standards.

Conﬁguration

The latest software versions are installed in the antenna and control unit.

RF radiation hazard zones were conﬁgured according to the customer’s requirements.

TCP/IP properties were correctly conﬁgured on the customer’s networked computer(s).

Testing

During startup, all system indicators showed normal status.

The system was tested by connecting to the KVH Test Page: http://208.83.165.11/mbbtest.

The customer was educated about service activation, system operation, radiation hazard, and fees.

TracPhone V3 Installation Checklist

Otros manuales para TracPhone V3

Tabla de contenidos

Otros manuales de Antena de KVH Industries

KVH Industries

KVH Industries TracPhone V11IP Manual de usuario

KVH Industries

KVH Industries Ka Tri-Americas LNB Manual de usuario

KVH Industries

KVH Industries TracNet H30 Manual de usuario

KVH Industries

KVH Industries TracVision A5 Guía de instalación

KVH Industries

KVH Industries TracVision M9 Guía

KVH Industries

KVH Industries TracPhone V7 Guía

KVH Industries

KVH Industries TracPhone V3 Guía

KVH Industries

KVH Industries TracPhone V3HTS Manual de usuario

KVH Industries

KVH Industries TracPhone V11IP Manual de usuario

KVH Industries

KVH Industries TracPhone V11 Manual de usuario

KVH Industries

KVH Industries TracPhone V11 Manual de usuario

KVH Industries

KVH Industries TracPhone V11 hts Manual de usuario

KVH Industries

KVH Industries TracVision HD11 Guía

KVH Industries

KVH Industries TracPhone V7-IP Manual de usuario

KVH Industries

KVH Industries SAILOR 4300 Guía rápida

KVH Industries

KVH Industries TracVision Land Mobile Antenna Guía

KVH Industries

KVH Industries TracPhone V3IP Manual de usuario

KVH Industries

KVH Industries TracVision M9 Guía

KVH Industries

KVH Industries TracPhone V7-HTS Guía

KVH Industries

KVH Industries TracNet H30 Manual de usuario

KVH Industries

KVH Industries TracVision 6 Manual de usuario

KVH Industries

KVH Industries TrackPhone V7 Manual de usuario

KVH Industries

KVH Industries TracVision TV3 Manual de usuario

KVH Industries

KVH Industries TracVision HDTV Converter Manual de usuario

Manuales populares de Antena de otras marcas

Alfa Network

Alfa Network APA-L01 Manual de usuario

Naval

Naval PR-422CA Manual de usuario

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Manual de usuario

TERK Technologies

TERK Technologies TV44 Manual de usuario

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Manual de usuario

HP J8999A Manual de usuario

MobilSat

MobilSat MSP-S Manual de usuario

Steren

Steren ANT-UHF 13 Manual de usuario

Novatel

Novatel 600-G Manual de operación

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Manual de usuario

TRENDnet

TRENDnet TEW-AO12O Manual de usuario

Radio Shack

Radio Shack 15-1837 Manual de usuario

CommScope

CommScope CMAX-OMFX-43M-I53 Manual de usuario

Ramsey Electronics

Ramsey Electronics DAP25 Manual de usuario

COBHAM

COBHAM SAILOR 800 VSAT Manual de uso y cuidado

Trango Systems

Trango Systems AD900-9 Manual de usuario

Steren

Steren ANT-100 Manual de usuario

Proxim

Proxim 5054-PA-23 Manual de usuario