Kurt 3400V Series Manual de instrucciones
3400V-Series Vise
“Manual” Base
Assembly
3400V-Forward
3410V- Reverse
Operating Instructions Manual
ENGLISH
2ENGLISH |
Table of Contents
Introduction .................................................................................................................3
Installation & Assembly Guide...........................................................................4-5
3400V Parts List...........................................................................................................8
3400V Mechanical Drawing....................................................................................9
Maintenance Schedule...................................................................................... 8-10
Troubleshooting Tips ............................................................................................. 12
Vise Data
Use this to ll out information about your vise for quick reference.
Purchase Date: _______ -_______-_______
Purchase Order: _______________________
Purchased From: _______________________
Delivery Date: _______________________
Serial No.: _______________________
Note:
Make sure to register your warranty online at kurtworkholding.com
Table of Contents
3| ENLGISH
Introduction
Thank you for purchasing a Kurt vise. The Versatile Lock
3400-Series AngLock vise has a time proven design and
the outstanding accuracy of this product is second to none.
Backed by a lifetime warranty, this product will last many
years when used and maintained properly.
The original Kurt Anglock vises are designed for precision
clamping. The“Pull-type” action of the 3400 Versatile Lock design
reduces
stationary jaw deection by at least 80%. This vise has a one-
piece body and stationary jaw design which reduce weight and
increases strength while providing .0005 clamping repeatability.
It oers ultra-high precision through many important features.
Features include: Ground sides that allow side mounting, upright
and back to back mounting, using the body through holes allows
side by side mounting.
With four dierent models including standard and reverse in both
manual and hydraulic conguration these vises are truly versatile.
The patented Anglock design allows the movable jaw to
advance in such a way that each pound of force forward induces
a ½ pound force downward which minimizes the jaw lift and
increases accuracy. This combined with the needle bearings
increases jaw clamping pressure. Other features include: 80,000
psi ductile iron body, hardened vise bed & case hardened jaw
plates, semi-hard steel screw.
Introduction
4ENGLISH | Set-Up Instructions
Installation & Assembly Guide
Now that you have your new Kurt 3400-Series vise, it’s time to set-up
and begin using it. You will see that your new vise comes with a Kurt
swivel handle, two chip guards (short & long)supplied in the shipping
carton. The chip guard rests between the ways of the vise and can
be trimmed to size to help keep chips out of the screw. The handle is
specically designed to provide maximum torque to your vise. Your
vise should be mounted to a clean at surface. The surface and the
vise must be free of any chips, dirt or debris of any kind. The mounting
surface can be honed if necessary. Clean the bottom of the vise with
solvent or other cleaner if needed.
To minimize vise bed deection, clamp your Kurt vise to your machine
table, pallet, or sub-plate using the built-in clamping slots provided. To
access the through holes, simply pick the edge of the protective cap
up and expose the counter bored hole. Replace the cap after you have
mounted the vise to keep debris out of the holes. If you are mounting
the vise on it’s side or back to back, other clamping methods may be
required.
Torque Ft-Lbs Manual V-Series
10 1050
20 2195
30 3435
40 4673
50 6243
60 7500
Manual Vise Clamping Force Lbs.
5| ENLGISH
Operating Instructions
Additional clamping can be used, but may not be necessary.
Please be sure to exercise good judgment when securing your
vise to the mounting surface. Be sure your vise is secured and
will not move when applying the machine pressure.
Operating Instructions
For proper vise operation place the handle on to the hex end of
the vise. Rotate clockwise to clamp and counterclockwise to un-
clamp your vise. is handle combined with the correct amount
of torque will provide you with all the clamping force you will
need to machine your parts. A high quality calibrated torque
wrench can be used if needed. DO NOT use any other type of
pressure to open or close your vise.
e uses of handle extensions, air impact wrenches, breaker
bars or hammer strikes are not recommended and will void the
warranty if used. is will also cause damage to the thrust bear-
ing and screw threads. If you need more clamping force you may
need to upgrade to a larger vise.
To properly clamp a part in your Kurt vise you should place
the part in the center of the jaws resting on the ways of the vise.
Clamping only on one side or above the movable and stationary
jaws can result in jaw li or loss of accuracy. (See Fig. on next
page)
If one-sided clamping is necessary you MUST use a dummy part
on the other side. When using parallels or step jaws you must se-
lect a size that keeps the bottom of the clamped part at or below
the top of the movable and stationary jaws. Always use jaw plates
for clamping. If jaw plates are not used,the mounting surface of
the movable and stationary jaw will be damaged. is will result
in reduced clamping accuracy and repeatability.
6ENGLISH | Operating Instructions
7| ENLGISH
Maintenance Log/Notes:
Maintenance Log/Notes
8ENGLISH | D40 Mechanical Drawing
3400V Parts List
ITEM# PART# DESCRIPTION QTY
1 3400V-1 BODY,MACH 1
2 3400V-5 SCREW 1
3 DL430-2 MOVABLE JAW 1
4 3400V-3 NUT 1
5 DL400-111 KURT LOGO TAF
6 PT400-211 BRUSH SEAL 2
7 3400V-99 O-RING #117 1
8 D40-42 THRUST WASHER 2
9 D40-41 THRUST BEARING 1
10 HDHLM4-96 O-RING #125 1
11 3400V-8 2-PIECE RETAINING NUT 1
12 00-1191 SHCS 8-32 X .375 4
13 D40-315 4” GROOVE JAW PLATE 1
14 00-1355 SCHS 3/8-16X 1.00LG 4
15 3400V-191 PROTECTIVE 2
16 605-02 O-RING 2
17 D40-7 JAW PLATE 1
18 D40-9 SEGMENT 1
19 01-3906 SHSS HDOG 3/8-16 X .625 1
20 3400-147 RETAINING RING 1
21 3400V-224 SCREW SUPPORT 1
22 WRSL46 WORKSTOP 1
23 3400V-102 MODEL/SERIAL TAG 1
24 07-0230 U-TYPE DRIVE SCREW 2
25 DL400-248 CHIP GUARD, SHORT 1
26 DL400-249 CHIP GUARD, LONG 1
27 D40I-10-SA 4”HANDLE ASSEMBLY 1
ITEMS 5,23,24 ARE NOT SHOWN ON THE DRAWING.
9| ENLGISH
Maintenance Schedule
3400V DRAWING
10 ENGLISH |
ITEM# PART# DESCRIPTION QTY
1 3400V-1 BODY,MACH 1
2 3410V-5 SCREW 1
3 DL430-2 MOVABLE JAW 1
4 3410V-3 NUT 1
5 DL400-111 KURT LOGO TAF
6 PT400-211 BRUSH SEAL 2
7 3600AA-68 O-RING #115 1
8 D40-42 THRUST WASHER 2
9 D40-41 THRUST BEARING 1
10 HDHLM4-96 O-RING #125 1
11 3400V-8 2-PIECE RETAINING NUT 1
12 00-1191 SHCS 8-32 X .375 4
13 D40-315 4” GROOVE JAW PLATE 1
14 00-1355 SCHS 3/8-16X 1.00LG 4
15 3400V-191 PROTECTIVE 2
16 605-02 O-RING 2
17 D40-7 JAW PLATE 1
18 D40-9 SEGMENT 1
19 01-3906 SHSS HDOG 3/8-16 X .625 1
20 WSRL46 WORKSTOP 1
21 3410-102 MODEL/SERIAL TAG 1
22 07-230 U-TYPE DRIVE SCREW 2
23 DL400-248 CHIP GUARD, SHORT 1
24 DL400-249 CHIP,GAUD, LONG 1
25 D40I-10-SA 4”HANDLE ASSEMBLY 1
ITEMS 5,23,24 ARE NOT SHOWN ON THE DRAWING.
3410V Parts List
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
