KTM RC 125 2018 Manual

SETUP INSTRUCTIONS 2018

RC 125

Art. no. 3213840en

INTRODUCTION

*3213840en*

3213840en

01/2018

INTRODUCTION

Perform the work described in these setup instructions before the vehicle is delivered to the customer.

Read the setup instructions in their entirety before beginning work.

All specifications are non-binding. KTM Sportmotorcycle GmbH specifically reserves the right to modify or delete

technical specifications, prices, colors, forms, materials, services, designs, equipment, etc., without prior notice

and without specifying reasons, to adapt these to local conditions, as well as to stop production of a particular

model without prior notice. KTM accepts no liability for delivery options, deviations from figures and descriptions,

misprints, and other errors. The models portrayed partly contain special equipment that does not belong to the

regular scope of supply.

These setup instructions were written to correspond to the latest state of this series. We reserve the right to make

changes in the interest of technical advancement without at the same time updating this manual.

We shall not provide a description of general workshop methods. Likewise, safety rules that apply in a workshop

are not specified here. It is assumed that the work will be performed by a fully trained mechanic.

Reproduction, even in part, as well as copying of all kinds, is permitted only with the express written permission

of the copyright owner.

ISO 9001(12 100 6061)

According to the international quality management standard ISO 9001, KTM uses quality assur-

ance processes that lead to the maximum possible quality of the products.

Issued by: TÜV Management Service

KTM Sportmotorcycle GmbH

Stallhofnerstraße 3

5230 Mattighofen, Austria

This document is valid for the following models:

RC 125 EU (F5003R1, F5003R2)

1 MEANS OF REPRESENTATION

1.1 Symbols used

The meaning of specific symbols is described below.

Indicates an expected reaction (e.g. of a work step or a function).

Indicates an unexpected reaction (e.g. of a work step or a function).

Indicates a page reference (more information is provided on the specified page).

Indicates information with more details or tips.

Indicates the result of a testing step.

Indicates a voltage measurement.

Indicates a current measurement.

Indicates a resistance measurement.

Indicates the end of an activity including potential rework.

1.2 Formats used

The typographical formats used in this document are explained below.

Proprietary name Indicates a proprietary name.

Name®Indicates a protected name.

Brand™ Indicates a brand available on the open market.

Underlined terms Refer to technical details of the vehicle or indicate technical terms, which

are explained in the glossary.

SETUP 2

2.1 Unpacking and setting up the vehicle

A00034-10

–Remove the straps and box.

S01886-01

–Remove the adhesive tape in the upper area of the motorcycle.

A00043-10

–Roll down the film at the sides.

Info

To avoid damaging the motorcycle during unpacking,

leave the other films on the vehicle until you have fin-

ished work on the vehicle.

–Remove the separate enclosure and unpack it. Check the sepa-

rate enclosure for completeness.

–Check the vehicle for transport damage.

S01885-10

Condition

Left and right handlebar stub not mounted.

–Remove protective film on the left and right handlebar

stub.

–Mount left and right handlebar stub on the upper triple

clamp.

Info

Make sure the cables and wiring are positioned cor-

rectly.

–Mount and tighten screws 1.

Guideline

Screw, handle-

bar stub

M6 8 Nm (5.9 lbf ft)

Loctite®243™

–Mount and tighten screws 2.

Guideline

Screw, anti-rotation

lock, handlebar

stub

M5 4 Nm (3 lbf ft)

2 SETUP

–Check the clutch lever play. ( p. 6)

–Check the play in the throttle cable. ( p. 7)

S01888-10

–Position damping rubber 3on both sides.

–Join plug-in connector 4of the mirror on both sides.

–Position the rear mirror on both sides. Mount and tighten the

screws.

–Position all controls in their exact positions on the handlebar.

–Tighten all screws.

F01048-10

–Mount reflector 5with spring washers 6on holding

plate 7.

–Mount the retaining plate on the license plate holder.

–Mount the license plate holder.

–Carefully loosen and remove the tension belt over the

swingarm.

Info

An assistant prevents the motorcycle from falling over.

–Carefully loosen and remove the tension belts around the lower

triple clamp.

The vehicle is released at the front.

–Take the vehicle off the palette together with an assistant.

Warning

Risk of injury Battery acid and battery gases cause

serious chemical burns.

–Keep batteries out of the reach of children.

–Wear suitable protective clothing and safety

glasses.

–Avoid contact with battery acid and battery gases.

–Keep sparks or open flames away from the battery.

–Only charge batteries in well-ventilated rooms.

–Rinse the affected area immediately with plenty of

water in the event of contact with the skin.

–Rinse eyes with water for at least 15 minutes and

consult a doctor immediately if battery acid and

battery gases get into the eyes.

–Fill the battery.

Info

Read the notes in the battery package.

–Recharge the battery. ( p. 10)

–Remove the front rider's seat. ( p. 8)

–Store the tool set below the seat.

–Remove the battery cover. ( p. 9)

SETUP 2

S01889-01

–Remove spare key and KEYCODECARD and keep in a safe place

for the handover.

–Install the battery. ( p. 11)

–Remove the remaining films.

–Refuel. ( p. 14)

–Prepare the vehicle according to the specifications in the

KTM Dealer.net for handover to the customer.

3 WORK

3.1 Checking the clutch lever play

Note

Clutch damage If there is no free travel by the clutch lever, the clutch will begin to slip.

–Check the free travel of the clutch lever each time before using the motorcycle.

–Adjust the free travel of the clutch lever when necessary in accordance with the specification.

V00625-11

–Check the clutch lever for smooth operation.

–Move the handlebar to the straight-ahead position.

–Pull the clutch lever until resistance is perceptible, and deter-

mine the play in the clutch lever A.

Clutch lever play A1 … 3 mm (0.04 …

0.12 in)

» If the clutch lever play does not meet the specified value:

–Adjust play in the clutch lever. ( p. 6)

–Move the handlebar to and fro over the entire steering range.

The clutch lever play must not change.

» If the clutch lever play changes:

–Check the routing of the clutch cable.

3.2 Adjusting play in the clutch lever

V00672-10

–Move the handlebar to the straight-ahead position.

–Push back sleeve 1.

–Loosen lock nut 2.

–Adjust the play in the clutch level Aby turning adjusting

screw 3.

Guideline

Clutch lever play A1 … 3 mm (0.04 …

0.12 in)

–Tighten lock nut 2.

–Position bellows 1.

WORK 3

3.3 Checking the play in the throttle cable

400192-11

–Check the throttle grip for smooth operation.

–Move the handlebar to the straight-ahead position. Turn the

throttle grip back and forth slightly and determine the play in

throttle cable A.

Throttle cable play A3 … 5 mm (0.12 … 0.2 in)

» If the throttle cable play does not meet the specified value:

–Adjust the play in the throttle cable. ( p. 7)

Danger

Danger of poisoning Exhaust gases are toxic and inhal-

ing them may result in unconsciousness and death.

–Always make sure there is sufficient ventilation

when running the engine.

–Use an effective exhaust extraction system when

starting or running the engine in an enclosed

space.

–Start the engine and let it run idle. Move the handlebar to and

fro over the entire steering range.

The idle speed must not change.

» If the idle speed changes:

–Check throttle cable routing.

3.4 Adjusting the play in the throttle cable

V00671-10

–Move the handlebar to the straight-ahead position.

–Push back sleeve 1.

–Loosen lock nut 2.

–Adjust the play in the throttle cable by turning adjusting

screw 3.

Guideline

Throttle cable play 3 … 5 mm (0.12 … 0.2 in)

–Tighten lock nut 2.

–Slide on sleeve 1.

3.5 Removing the passenger seat

Preparatory work

–Remove the front rider's seat. ( p. 8)

3 WORK

V00639-10

Main work

–Remove screw 1with washer.

–Lift and take off the passenger seat.

3.6 Mounting the passenger seat

V00640-10

Main work

–Position passenger seat.

Both hooks 1engage in the holders 2.

–Lower the front of the passenger seat and push back.

V00639-11

–Mount and tighten screw 3with the washer.

Guideline

Screw, passenger

seat

M6 7 Nm (5.2 lbf ft)

Warning

Danger of accidents The seat can come loose from the

anchoring if it is not mounted correctly.

–After assembly, check whether the seat is correctly

locked and cannot be pulled up.

–Check that the passenger seat is mounted correctly.

Finishing work

–Mount the front rider's seat. ( p. 9)

3.7 Removing the front rider's seat

V00633-10

–Insert the ignition key in seat lock 1and turn it clockwise.

–Raise the rear of the front rider's seat, pull it toward the rear,

and remove it upward.

–Remove the ignition key from the seat lock.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Motocicleta de KTM

KTM

KTM 660 SMC SUPERMOTO 2003 Manual de usuario

KTM

KTM 125 SX Manual de usuario

KTM

KTM 250 SX-F EU 2017 Manual de usuario

KTM

KTM 400 EXC FACTORY EDITION EU Manual de usuario

KTM

KTM 1190 Adventure R EU Manual de usuario

KTM

KTM 250 EXC-F 2014 Manual

KTM

KTM 150 EXC TPI 2021 Manual

KTM

KTM 250 EXC-F EU Manual de usuario

KTM

KTM 1290 Super Adventure Manual de usuario

KTM

KTM 690 Duke EU 2012 Manual de usuario

KTM

KTM 450 EXC RACING 2006 Manual de usuario

KTM

KTM Freeride 250 R EU Manual de usuario

KTM

KTM 2010 990 Super Duke R Manual de usuario

KTM

KTM 450 EXC EU Manual de usuario

KTM

KTM 65 SX 2017 Manual de usuario

KTM

KTM LC4 ADVENTURE R 640 2000 Guía del usuario

KTM

KTM RC 250 R Manual de usuario

KTM

KTM 625 SXC Guía

KTM

KTM 450 SMR Manual de usuario

KTM

KTM 250 EXC E-Starter EU 2010 Manual de usuario

KTM

KTM 950 ADVENTURE 2003 Manual de usuario

KTM

KTM Freeride 250 R EU 2016 Manual de usuario

KTM

KTM 450 SMR Manual del propietario

KTM

KTM 690 DUKE R EU Manual de usuario

Manuales populares de Motocicleta de otras marcas

OHVALE

OHVALE GP-0 Manual de lista de piezas

Yamaha

Yamaha Star XV19CTSZ 2009 Manual de usuario

HYOSUNG

HYOSUNG ST7 Manual de usuario

Husqvarna

Husqvarna FC 250 2016 Manual de usuario

Ducati

Ducati SCRAMBLER 800 Manual de instrucciones

MOTO GUZZI

MOTO GUZZI QUOTA 1100 ES Manual de usuario

APRILIA

APRILIA ETV MILLE CAPONORD - PART1 02-2001 Manual de usuario

Yamaha

Yamaha 2006 YZF-R1V Manual de usuario

Fantic

Fantic Enduro 125 Manual de usuario

Ducati

Ducati Supersport 750 desmodue Manual de usuario

MV Agusta

MV Agusta 2008 F4 312RR 1078 Manual de instrucciones

Yamaha

Yamaha XVS650A Manual de usuario

Yamaha

Yamaha YZF-R6T(C) Manual

Ducati

Ducati 748 monoposto strada Manual de usuario

ATK

ATK 1988 250 Manual de usuario

Excelsior-HENDERSON

Excelsior-HENDERSON 1999 HCX Manual de usuario

Triumph

Triumph Thunderbird Manual de usuario

Yamaha

Yamaha 2006 FJR1300A Manual de usuario