KTM 250 EXC TPI EU 2018 Manual

SETUP INSTRUCTIONS 2018

250 EXC TPI

250 EXC Six Days TPI

250 XC‑W TPI

300 EXC TPI

300 EXC Six Days TPI

Art. no. 3213730en

INTRODUCTION

*3213730en*

3213730en

06/2017

INTRODUCTION

Perform the work described in these setup instructions before the vehicle is delivered to the customer.

Read the setup instructions in their entirety before beginning work.

These setup instructions were written to correspond to the latest state of this series. We reserve the right to make

changes in the interest of technical advancement without at the same time updating this manual.

We shall not provide a description of general workshop methods. Likewise, safety rules that apply in a workshop

are not specified here. It is assumed that the work will be performed by a fully trained mechanic.

All specifications are non-binding. KTM Sportmotorcycle GmbH specifically reserves the right to modify or delete

technical specifications, prices, colors, forms, materials, services, designs, equipment, etc., without prior notice

and without specifying reasons, to adapt these to local conditions, as well as to stop production of a particular

model without prior notice. KTM accepts no liability for delivery options, deviations from figures and descriptions,

misprints, and other errors. The models portrayed partly contain special equipment that does not belong to the

regular scope of supply.

Reproduction, even in part, as well as copying of all kinds, is permitted only with the express written permission

of the copyright owner.

ISO 9001(12 100 6061)

According to the international quality management standard ISO 9001, KTM uses quality assur-

ance processes that lead to the maximum possible quality of the products.

Issued by: TÜV Management Service

KTM Sportmotorcycle GmbH

Stallhofnerstraße 3

5230 Mattighofen, Austria

This document is valid for the following models:

250 EXC TPI EU (F7303R7)

250 EXC Six Days TPI EU (F7303R2)

250 XC‑W TPI US (F7375R4)

300 EXC TPI EU (F7403R7)

300 EXC Six Days TPI EU (F7403R2)

1 MEANS OF REPRESENTATION

1.1 Symbols used

The meaning of specific symbols is described below.

Indicates an expected reaction (e.g. of a work step or a function).

Indicates an unexpected reaction (e.g. of a work step or a function).

Indicates a page reference (more information is provided on the specified page).

Indicates information with more details or tips.

Indicates the result of a testing step.

Indicates a voltage measurement.

Indicates a current measurement.

Indicates a resistance measurement.

Indicates the end of an activity including potential rework.

1.2 Formats used

The typographical formats used in this document are explained below.

Proprietary name Indicates a proprietary name.

Name®Indicates a protected name.

Brand™ Indicates a brand available on the open market.

Underlined terms Refer to technical details of the vehicle or indicate technical terms, which

are explained in the glossary.

2 SETUP

2.1 Unpacking and setting up the vehicle

E00851-10

Condition

Packaging V2

–Remove the box and the plastic packaging.

Info

An assistant prevents the motorcycle from falling

over. To avoid damaging the motorcycle during the

setup, leave the protective film on the vehicle until

you have finished.

–Remove the separate enclosure and unpack it. Check that

the scope of supply is complete using the enclosed pack-

ing list.

–Have a lift stand available.

Lift stand (78129955100)

–Carefully loosen and remove the tension belt of the footrest

mount.

Info

An assistant prevents the motorcycle from falling

over.

402050-01

–Together with an assistant, take the vehicle off the pallet.

–Position the vehicle on a lift stand.

–Check the vehicle for transport damage.

–Remove the headlight mask with the headlight. ( p. 30)

H02474-10

(All EXC models)

–Position the turn signal indicator lamp 1in the com-

bination instrument bracket.

E00850-10

Condition

Packaging V12

–Remove the box and the plastic packaging.

2 SETUP

Info

An assistant prevents the motorcycle from falling

over.

To avoid damaging the motorcycle during the setup,

leave the protective film on the vehicle until you

have finished.

–Remove and unpack the separate enclosure and attach-

ments. Check that the scope of supply is complete using

the enclosed packing list.

–Have a lift stand available.

Lift stand (78129955100)

–Remove the two cable ties on the triple clamp.

402051-01

–Together with an assistant, take the vehicle off the pallet.

–Position the vehicle on a lift stand.

–Check the vehicle and attachments for transport damage.

–Install the shock absorber. ( p. 24)

H02474-10

(All EXC models)

–Position the turn signal indicator lamp 1in the com-

bination instrument bracket.

H02537-10

(All EXC models)

–Position the connector retainer and combination instru-

ment on the upper triple clamp.

–Mount and tighten screws 2.

Guideline

Remaining screws,

chassis

M6 10 Nm

(7.4 lbf ft)

H02538-10

(250 XC‑W TPI US)

–Position the combination instrument on the upper

triple clamp.

–Mount and tighten screws 2with the collar bushings.

Guideline

Remaining screws,

chassis

M6 10 Nm

(7.4 lbf ft)

2 SETUP

–Route the clutch line with the clutch master cylinder

toward the front between the upper and lower triple

clamps.

–Install the fork legs. ( p. 25)

S01414-10

(All standard EXC/XC-W models)

–Remove screws 3and take off handlebar supports.

–Move the handlebar supports to the desired position and

mount and tighten screws 3.

Guideline

Screw, handle-

bar support

M10 40 Nm (29.5 lbf ft)

Loctite®243™

Info

Position the left and right handlebar supports

evenly.

E00483-01

Warning

Danger of accidents A repaired handlebar poses a

safety risk.

If the handlebar is bent or straightened, the mate-

rial becomes fatigued. The handlebar may break

as a result.

–Change the handlebar if the handlebar is dam-

aged or bent.

–Position the handlebar.

Info

Make sure the cables and wiring are positioned cor-

rectly.

–Position the handlebar clamps. Mount and tighten the

screws evenly.

Guideline

Screw, handlebar

clamp

M8 20 Nm

(14.8 lbf ft)

Info

The markings on the handlebar should be at the

center of the handlebar clamps.

Keep the gap widths equal when tightening.

2 SETUP

S01415-10

(All Six Days models)

–Remove screws 3and take off handlebar supports.

–Move the handlebar supports to the desired position and

mount and tighten screws 3.

Guideline

Screw, handle-

bar support

M10 40 Nm (29.5 lbf ft)

Loctite®243™

Info

Position the left and right handlebar supports

evenly.

S01413-01

Warning

Danger of accidents A repaired handlebar poses a

safety risk.

If the handlebar is bent or straightened, the mate-

rial becomes fatigued. The handlebar may break

as a result.

–Change the handlebar if the handlebar is dam-

aged or bent.

–Position the handlebar.

Info

Make sure the cables and wiring are positioned cor-

rectly.

–Position the handlebar clamps. Mount and tighten the

screws evenly.

Guideline

Screw, handlebar

clamp

M8 20 Nm

(14.8 lbf ft)

Info

The markings on the handlebar should be at the

center of the handlebar clamps.

Keep the gap widths equal when tightening.

2 SETUP

F01132-01

(All EXC models)

–Position the controls on the right half of the handlebar.

F01136-01

(250 XC‑W TPI US)

–Position the controls on the right half of the handlebar.

S01453-01

(All EXC models)

–Position the controls on the left half of the handlebar.

S01454-01

(250 XC‑W TPI US)

–Position the controls on the left half of the handlebar.

2 SETUP

402148-01

(All EXC models)

–Mount the turn signal switch.

E00855-01

(All Six Days models)

Warning

Voiding of the government approval for road use and

the insurance coverage If the map switch is

installed, the vehicle's approval for road use is

invalidated.

–Only operate the vehicle in closed-off areas

away from public road traffic if the map switch

is installed.

–Position the map switch with the clamp on the right han-

dlebar half.

Info

Read the accompanying KTM PowerParts instruc-

tions.

F01133-10

Condition

Packaging V12

(All EXC models)

–Insert indicator lamp 4in the socket.

–Join all plug-in connectors to the plug-in holder.

–Route the cable without tension and secure with cable

tie.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Motocicleta de KTM

KTM

KTM 250 EXC RACING 2004 Manual de usuario

KTM

KTM 1290 SUPER ADVENTURE R 2018 Manual de usuario

KTM

KTM 250 EXC Six Days TPI 2019 Manual de usuario

KTM

KTM 50 SX PRO SENIOR LC Manual

KTM

KTM 250 EXC 2023 Manual de usuario

KTM

KTM 85 SX 2018 Manual

KTM

KTM 890 DUKE R 2021 Manual de usuario

KTM

KTM 1190 Adventure R EU Manual de usuario

KTM

KTM 450 SX F EU 2010 Manual

KTM

KTM 690 Enduro R EU 2014 Manual

KTM

KTM 200 Duke 2017 Manual de usuario

KTM

KTM 890 ADVENTURE R 2021 Manual

KTM

KTM 690 Duke AUS/UK 2014 Manual de usuario

KTM

KTM 690 SMC R 2016 Series Manual

KTM

KTM 390 Duke 2015 COL Manual

KTM

KTM 1290 Super Adventure R EU 2019 Manual

KTM

KTM 690 Enduro R EU Manual de usuario

KTM

KTM 950 ADVENTURE 2003 Manual de usuario

KTM

KTM F8103S4 Manual de usuario

KTM

KTM Freeride 350 EU Manual de usuario

KTM

KTM Freeride E-SM 2016 Manual

KTM

KTM 500 EXC-F 2023 Manual de usuario

KTM

KTM 450 EXC EU Manual de usuario

KTM

KTM 2011 990 Supermoto T USA Manual de usuario

Manuales populares de Motocicleta de otras marcas

OHVALE

OHVALE GP-0 Manual de lista de piezas

Yamaha

Yamaha Star XV19CTSZ 2009 Manual de usuario

HYOSUNG

HYOSUNG ST7 Manual de usuario

Husqvarna

Husqvarna FC 250 2016 Manual de usuario

Ducati

Ducati SCRAMBLER 800 Manual de instrucciones

MOTO GUZZI

MOTO GUZZI QUOTA 1100 ES Manual de usuario

APRILIA

APRILIA ETV MILLE CAPONORD - PART1 02-2001 Manual de usuario

Yamaha

Yamaha 2006 YZF-R1V Manual de usuario

Fantic

Fantic Enduro 125 Manual de usuario

Ducati

Ducati Supersport 750 desmodue Manual de usuario

MV Agusta

MV Agusta 2008 F4 312RR 1078 Manual de instrucciones

Yamaha

Yamaha XVS650A Manual de usuario

Yamaha

Yamaha YZF-R6T(C) Manual

Ducati

Ducati 748 monoposto strada Manual de usuario

ATK

ATK 1988 250 Manual de usuario

Excelsior-HENDERSON

Excelsior-HENDERSON 1999 HCX Manual de usuario

Triumph

Triumph Thunderbird Manual de usuario

Yamaha

Yamaha 2006 FJR1300A Manual de usuario