KTM 125 SX 2017 Manual

SETUP INSTRUCTIONS 2017

125 SX

150 SX

250 SX

250 XC

300 XC

Art. no. 3213573en

INTRODUCTION 1

*3213573en*

3213573en

08/2016

INTRODUCTION

Perform the work described in these setup instructions before the vehicle is delivered to the customer.

Read the setup instructions in their entirety before beginning work.

These setup instructions were written to correspond to the latest state of this series. We reserve the right to make changes in the interest

of technical advancement without at the same time updating this manual.

We shall not provide a description of general workshop methods. Likewise, safety rules that apply in a workshop are not specified here. It

is assumed that the work will be performed by a fully trained mechanic.

All specifications are non-binding. KTM Sportmotorcycle GmbH specifically reserves the right to modify or delete technical specifications,

prices, colors, forms, materials, services, designs, equipment, etc., without prior notice and without specifying reasons, to adapt these to

local conditions, as well as to stop production of a particular model without prior notice. KTM accepts no liability for delivery options, devi-

ations from illustrations and descriptions, misprints, and other errors. The models portrayed partly contain special equipment that does not

belong to the regular scope of supply.

Reproduction, even in part, as well as copying of all kinds, is permitted only with the express written permission of the copyright owner.

ISO 9001(12 100 6061)

According to the international quality management standard ISO 9001, KTM uses quality assurance processes that lead to

the maximum possible quality of the products.

Issued by: TÜV Management Service

KTM Sportmotorcycle GmbH

5230 Mattighofen, Austria

This document is valid for the following models:

125 SX EU (F6101Q0)

125 SX US (F6175Q0)

150 SX EU (F6101Q1)

150 SX US (F6175Q1)

250 SX EU (F6301Q0)

250 SX US (F6375Q0)

250 XC US (F6375Q5)

300 XC US (F6475Q5)

1 MEANS OF REPRESENTATION 2

1.1 Symbols used

The meaning of specific symbols is described below.

Indicates an expected reaction (e.g. of a work step or a function).

Indicates an unexpected reaction (e.g. of a work step or a function).

Indicates a page reference (more information is provided on the specified page).

Indicates information with more details or tips.

Indicates the result of a testing step.

Denotes a voltage measurement.

Denotes a current measurement.

Denotes a resistance measurement.

1.2 Formats used

The typographical formats used in this document are explained below.

Proprietary name Identifies a proprietary name.

Name®Identifies a protected name.

Brand™ Identifies a trademark.

Underlined terms Refer to technical details of the vehicle or indicate technical terms, which are explained

in the glossary.

2 SETUP 3

2.1 Unpacking and setting up the vehicle

B02176-10

Package 2

–Remove the box and the plastic film.

Info

To avoid damaging the motorcycle during the setup, leave the protective

film on the vehicle until you have finished.

–Remove the separate enclosure and unpack it. Check that everything is

included and complete using the enclosed packing list.

–Have a lift stand available.

Lift stand (78129955100)

–Carefully loosen and remove the tension belt of the footrest mount.

Info

An assistant prevents the motorcycle from falling over.

402050-01

–Together with an assistant, take the vehicle off the pallet.

–Position the vehicle on a lift stand.

–Check the vehicle for transport damage.

B02008-10

Package 12

–Remove the box and the plastic film.

Info

An assistant prevents the motorcycle from falling over.

To avoid damaging the motorcycle during the setup, leave the protective

film on the vehicle until you have finished.

–Remove the separate enclosure and unpack it. Check that everything is

included and complete using the enclosed packing list.

–Have a lift stand available.

Lift stand (78129955100)

–Together with an assistant, take the vehicle off the pallet.

402051-01

–Position the vehicle on a lift stand.

–Check the vehicle for transport damage.

K00613-10

–Remove the cardboard from around the shock absorber.

–Position the angle lever and linkage lever.

–Mount and tighten fitting .

Guideline

Nut, linkage lever to angle lever M14x1.5 80 Nm (59 lbf ft)

–Mount and tighten screw .

Guideline

Screw, bottom shock

absorber

M10 60 Nm

(44.3 lbf ft)

Loctite®2701™

2 SETUP 4

Info

Raise the wheel slightly to be able to mount the screw more easily.

–Route the clutch line with the clutch master cylinder toward the front between

the upper and lower triple clamps.

–Install the fork legs. ( p. 10)

K00620-10

–Remove screws . Take off the handlebar clamp. Remove the handlebar and lay it

to one side.

Info

Cover the components to protect them against damage.

Do not kink the cables and lines.

–Remove screws . Take off handlebar supports .

–Position rubber bushings and push through nuts from below.

–Place the handlebar supports in the required position.

Info

The handlebar supports are longer and higher on one side.

Position the left and right handlebar supports evenly.

–Mount and tighten screws .

Guideline

Screw, handlebar support M10 40 Nm

(29.5 lbf ft)

Loctite®243™

–Position the handlebar.

Info

Make sure the cables and wiring are positioned correctly.

–Position the handlebar clamp.

–Mount screws but do not tighten yet.

–First bolt the handlebar clamp with screws onto the longer, higher side of the

handlebar supports so that both parts touch.

–Tighten screws evenly.

Guideline

Screw, handlebar clamp M8 20 Nm

(14.8 lbf ft)

K00615-10

–Position the controls on the right half of the handlebar.

K00616-10

–Position the controls on the left half of the handlebar.

–Mount the cable tie(s).

–Mount the fuel tank breather.

–Install the front wheel. ( p. 10)

–Install the front fender. ( p. 11)

–Install the start number plate. ( p. 13)

2 SETUP 5

K00617-10

–Mount the handlebar cushion.

D00674-10

Left and right footrest (All SX models)

–Position the new footrest and pin.

Info

Only insert the pin to the extent that the spring can still be mounted.

K00621-10

–Position spring as shown.

Spring engages in area .

K00622-10

–Press the spring with special tool .

Pliers for footrest spring (79029083000)

The special tool is applied to area on the footrest.

–Mount pin .

K00623-10

–Mount the washer and split pin .

–Repeat these steps on the opposite side.

2 SETUP 6

R00757-10

Left footrest (All XC models)

–Raise the motorcycle with a lift stand. ( p. 9)

–Position the new footrest and pin.

Info

Only insert the pin to the extent that the spring can still be mounted.

K00624-10

–Position spring as shown.

Spring engages in area .

K00625-10

–Press the spring with special tool .

Pliers for footrest spring (79029083000)

The special tool is applied to area on the footrest.

–Mount pin .

K00626-10

–Mount the washer and split pin .

–Remove the motorcycle from the lift stand. ( p. 9)

D00674-10

Right footrest (All XC models)

–Position the new footrest and pin.

Info

Only insert the pin to the extent that the spring can still be mounted.

2 SETUP 7

K00621-11

–Position spring as shown.

Spring engages in area .

K00622-11

–Press the spring with special tool .

Pliers for footrest spring (79029083000)

The special tool is applied to area on the footrest.

–Mount pin .

K00623-11

–Mount the washer and split pin .

K00618-10

(All XC models)

–Recharge the battery. ( p. 11)

–Install the battery. ( p. 12)

K00512-12

–Position the frame protector on the left and right.

–Mount and tighten screws  with the washers.

Guideline

Screw, frame protector M5 3 Nm (2.2 lbf ft)

–Mount and tighten screws .

Guideline

Screw, frame protector M5 3 Nm (2.2 lbf ft)

–Mount the cable tie(s).

2 SETUP 8

–Unpack and mount the KTM PowerParts included in the delivery (optional).

Info

Read the accompanying KTM PowerParts fitting instructions.

–Apply the sticker included in the delivery (optional).

–Refuel. ( p. 13)

–Position all controls in their exact positions on the handlebar. Tighten all screws.

–Prepare the vehicle according to the specifications in the KTM Dealer.net for han-

dover to the customer.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Motocicleta de KTM

KTM

KTM 390 Adventure 2020 Manual de usuario

KTM

KTM Freeride 350 EU Manual

KTM

KTM 125 EXC Manual de usuario

KTM

KTM 390 ADVENTURE 2022 Manual

KTM

KTM 350 XC-F Manual de usuario

KTM

KTM 625 LC4 SUPERCOMPETITION Guía del usuario

KTM

KTM 3213459en Manual

KTM

KTM Freeride 250 R EU 2016 Manual de usuario

KTM

KTM 400 EXC RACING Manual de usuario

KTM

KTM Freeride 250 R 2017 Manual

KTM

KTM Freeride 250 R 2016 Manual

KTM

KTM 350 EXC-F AUS 2012 Manual

KTM

KTM 625 SXC Guía

KTM

KTM 450 EXC EU Manual de usuario

KTM

KTM 990 Adventure Baja Manual de usuario

KTM

KTM 300 EXC Manual de usuario

KTM

KTM 690 DUKE R EU Manual de usuario

KTM

KTM 1290 Super Adventure R EU 2019 Manual

KTM

KTM 50 MINI ADVENTURE Manual de usuario

KTM

KTM 390 Duke 2015 COL Manual

KTM

KTM 200 Duke 2017 Manual de usuario

KTM

KTM 450 EXC EU 2014 Manual

KTM

KTM 3CF6001G4EN Manual de usuario

KTM

KTM 450 SMR Manual de usuario

Manuales populares de Motocicleta de otras marcas

OHVALE

OHVALE GP-0 Manual de lista de piezas

Yamaha

Yamaha Star XV19CTSZ 2009 Manual de usuario

HYOSUNG

HYOSUNG ST7 Manual de usuario

Husqvarna

Husqvarna FC 250 2016 Manual de usuario

Ducati

Ducati SCRAMBLER 800 Manual de instrucciones

MOTO GUZZI

MOTO GUZZI QUOTA 1100 ES Manual de usuario

APRILIA

APRILIA ETV MILLE CAPONORD - PART1 02-2001 Manual de usuario

Yamaha

Yamaha 2006 YZF-R1V Manual de usuario

Fantic

Fantic Enduro 125 Manual de usuario

Ducati

Ducati Supersport 750 desmodue Manual de usuario

MV Agusta

MV Agusta 2008 F4 312RR 1078 Manual de instrucciones

Yamaha

Yamaha XVS650A Manual de usuario

Yamaha

Yamaha YZF-R6T(C) Manual

Ducati

Ducati 748 monoposto strada Manual de usuario

ATK

ATK 1988 250 Manual de usuario

Excelsior-HENDERSON

Excelsior-HENDERSON 1999 HCX Manual de usuario

Triumph

Triumph Thunderbird Manual de usuario

Yamaha

Yamaha 2006 FJR1300A Manual de usuario