KTM 125 EXC EU 2011 Manual

SETUP INSTRUCTIONS 2011

125 EXC EU

125 EXC SIX DAYS EU

200 EXC EU

200 EXC AUS

200 XC‑W USA

250 EXC EU

250 EXC AUS

250 EXC SIX DAYS EU

250 XC‑W USA

300 EXC EU

300 EXC AUS

300 EXC SIX DAYS EU

300 XC‑W USA

Art. no. 3211693en

INTRODUCTION 1

INTRODUCTION

The work described in these setup instructions must be performed before the vehicle is delivered to the customer.

Read the setup instructions in their entirety before beginning work.

Print out the current PDI form found on the KTM DEALER.NET.

These setup instructions were written to correspond to the latest state of this series. We reserve the right to make changes in the inter-

est of technical advancement without at the same time updating this manual.

We shall not provide a description of general workshop methods. Likewise, safety rules that apply in a workshop are not specified here.

It is assumed that the work will be performed by a fully trained mechanic.

All specifications are non-binding. KTM Sportmotorcycle AG in particular reserves the right to modify or delete technical specifica-

tions, prices, colors, forms, materials, services, designs, equipment, etc., without prior notice and without specifying reasons, to adapt

these to local conditions, as well as to stop production of a particular model without prior notice. KTM accepts no liability for delivery

options, deviations from illustrations and descriptions, as well as misprints and other errors. The models portrayed partly contain spe-

cial equipment that does not belong to the regular scope of delivery.

Reproduction, even in part, as well as copying of all kinds, is permitted only with the express written permission of the copyright

owner.

ISO 9001(12 100 6061)

According to the international quality management standard ISO 9001, KTM uses quality assurance processes that lead

to the maximum possible quality of the products.

Issued by: TÜV Management Service

KTM-Sportmotorcycle AG

5230 Mattighofen, Austria

MEANS OF REPRESENTATION 2

Symbols used

The symbols used are explained in the following.

Indicates an expected reaction (e.g. of a work step or a function).

Indicates an unexpected reaction (e.g. of a work step or a function).

Identifies a page reference (more information is provided on the specified page).

Denotes additional information or tips.

Denotes the result of a test step.

Denotes a voltage measurement.

Denotes a current measurement.

Denotes a resistance measurement.

Formats used

The typographical and other formats used are explained in the following.

Own name Indicates a proprietary name.

Name®Identifies a protected name.

Brand™ Identifies a brand in merchandise traffic.

SET‑UP 3

2.1Unpacking and setting up the vehicle

B00095-01

Packaging 2

–Remove the box and the plastic packaging.

Info

An assistant prevents the motorcycle from falling over.

To avoid damaging the motorcycle during the setup, leave the protective

film on the vehicle until you have finished.

–Remove the separate enclosure and unpack it. Check that the scope of delivery

is complete on the basis of the enclosed packing list.

–Have a lift stand available.

Lift stand (54829055000)

–Carefully loosen and remove the tensioning belt over the link fork.

Info

An assistant prevents the motorcycle from falling over.

–Carefully loosen and remove the tensioning belts around the lower triple clamp.

The vehicle is released at the front.

–Together with an assistant, take the vehicle off of the palette.

–Position the vehicle on a lift stand.

–Check the vehicle for transport damage.

600811-10

Package 12

–Remove the box and the plastic packaging.

Info

An assistant prevents the motorcycle from falling over.

To avoid damaging the motorcycle during the setup, leave the protective

film on the vehicle until you have finished.

–Remove the separate enclosure and unpack it. Check that the scope of delivery

is complete on the basis of the enclosed packing list.

–Have a lift stand available.

Lift stand (54829055000)

–Together with an assistant, take the vehicle off of the palette.

–Position the vehicle on a lift stand.

–Check the vehicle for transport damage.

B00094-01

–Install the shock absorber. ( p. 7)

600814-01

–Route the clutch line with the clutch master cylinder toward the front between

the upper and lower triple clamps.

–Position the fork legs and tighten the screws of the triple clamp.

Guideline

Screw, top triple clamp

(EXC EU/AUS)

M8 20 Nm

(14.8 lbf ft)

Screw, bottom triple clamp

(EXC EU/AUS)

M8 15 Nm

(11.1 lbf ft)

Screw, top triple clamp

(EXC SIX DAYS, XC‑W)

M8 17 Nm

(12.5 lbf ft)

Screw, bottom triple clamp

(EXC SIX DAYS, XC‑W)

M8 12 Nm

(8.9 lbf ft)

SET‑UP 4

Info

The upper milled groove in the fork leg must be flush with the top edge

of the upper triple clamp.

Position bleeder screws toward the front.

400223-10

–Remove screws . Remove the handlebar clamp.

–Remove screws . Remove the handlebar support.

–Place the handlebar support in the required position. Mount and tighten screws .

Guideline

Screw, handlebar support M10 40 Nm

(29.5 lbf ft)

Loctite®243™

Info

Position the left and right handlebar supports evenly.

600824-10

–Position the handlebar.

Info

Make sure cables and wiring are positioned correctly.

–Position the handlebar clamps. Mount and tighten the screws.

Guideline

Screw, handlebar clamp M8 20 Nm

(14.8 lbf ft)

Info

The markings on the handlebar should be at the center of the handlebar

clamps.

Keep the gap widths equal when tightening.

B00096-10

–Position the controls on the right half of the handlebar.

Info

The routing of the cables can be seen in the figure.

600817-10

–Position the controls on the left half of the handlebar.

Info

The figure shows how to route the clutch line and wiring harness.

SET‑UP 5

600818-10

(EXC, EXC SIX DAYS)

–Attach the retaining bracket for the connector, the turn signal bracket with the

turn signal and the speedometer to the upper triple clamp.

Guideline

Remaining screws, chassis M6 10 Nm

(7.4 lbf ft)

–Connect the connector.

600819-10

(XC-W)

–Attach the speedometer to the upper triple clamp.

Guideline

Remaining screws, chassis M6 10 Nm

(7.4 lbf ft)

–Connect the connector.

–Install the front fender. ( p. 9)

–Correctly mount the fuel tank breather.

B00539-01

–Secure the handlebar cushion with two cable binders.

(EXC, EXC SIX DAYS)

–Refit the headlight mask with the headlight. ( p. 10)

(XC-W)

–Install the start number plate. ( p. 10)

800042-10

–Mount the footrests with the springs and bolts. Secure the bolts using the washers

and pins.

Plier for footrest spring (58429083000)

800035-10

(All 250/300 models)

Warning

Risk of injury Battery acid and battery gases cause serious cauteriza-

tion.

–Keep batteries out of the reach of children.

–Wear suitable protective clothing and goggles.

–Avoid contact with battery acid and battery gases.

–Keep the battery away from sparks or open fire. Charge only in well

ventilated rooms.

–Flush with copious amounts of water in case of skin contact. If bat-

tery acid comes into contact with the eyes, flush the eyes with water

for at least 15 minutes and consult a physician.

–Fill the battery.

Info

Read the notes in the battery package.

–Recharge the battery. ( p. 8)

–Install the battery. ( p. 9)

SET‑UP 6

B00097-01

–Unpack and mount the KTM PowerParts included in the delivery (optional).

Info

Read the accompanying KTM PowerParts installation instructions.

–Apply the label included in the delivery (optional).

101037-01

(EXC, EXC SIX DAYS)

–Mount the mirror clamps on both sides.

101038-01

–Mount and tighten the rear mirror adapter and rear mirror on both sides.

–Mount the reflector.

–Position all controls exactly on the handlebar. Tighten all screws.

–Refuel. ( p. 11)

–Print out the current PDI form found on KTM DEALER.NET and perform the delivery

inspection.

WORK 7

3.1Removing the seat

500080-10

–Remove screw . Lift up the seat at the rear, pull it back and then remove from

above.

3.2Mounting the seat

500068-01

–Hook in the front of the seat at the collar bushing of the fuel tank, lower at the rear

and simultaneously push forward.

–Make sure that the seat is correctly locked in.

500080-10

–Mount and tighten screw of the seat fixation.

Guideline

Remaining screws, chassis M6 10 Nm (7.4 lbf ft)

3.3Installing the shock absorber

601156-11

(All 125/200 models)

–Push splash protector to the side and position the shock absorber. Mount

and tighten screw .

Guideline

Screw, top shock

absorber

M12 80 Nm

(59 lbf ft)

Loctite®2701

–Mount and tighten screw .

Guideline

Screw, bottom shock

absorber

M12 80 Nm

(59 lbf ft)

Loctite®2701

Info

The heim joint for the shock absorber at the swing arm is Teflon coated.

It must not be lubricated with grease or with other lubricants. Lubri-

cants dissolve the Teflon coating, thereby drastically reducing the ser-

vice life.

303393-11

(All 250/300 models)

–Push splash protector to the side and position the shock absorber. Mount

and tighten screw .

Guideline

Screw, top shock

absorber

M12 80 Nm

(59 lbf ft)

Loctite®2701

–Mount and tighten screw .

WORK 8

Guideline

Screw, bottom shock

absorber

M12 80 Nm

(59 lbf ft)

Loctite®2701

Info

The heim joint for the shock absorber at the swing arm is Teflon coated.

It must not be lubricated with grease or with other lubricants. Lubri-

cants dissolve the Teflon coating, thereby drastically reducing the ser-

vice life.

–Remove the motorcycle from the lift stand.

3.4Installing the front wheel

Warning

Danger of accidents Reduced braking efficiency due to oil or grease on the brake discs.

–Always keep the brake discs free of oil and grease, and clean them with brake cleaner when necessary.

500086-11

–Check the wheel bearing for damage and wear.

» If the wheel bearing is damaged or worn:

–Change the wheel bearing.

–Clean and grease shaft seal rings and bearing surface of the spacers.

Long-life grease ( p. 14)

–Insert the spacers.

500084-11

–Lift the front wheel into the fork, position it, and insert the wheel spindle.

–Mount and tighten screw .

Guideline

Screw, front wheel spindle M24x1.5 45 Nm

(33.2 lbf ft)

–Operate the hand brake lever several times until the brake linings are lying correctly

against on the brake disc.

–Remove the motorcycle from the lift stand.

–Pull the front wheel brake and push down hard on the fork several times to align

the fork legs.

–Tighten screws .

Guideline

Screw, fork stub M8 15 Nm

(11.1 lbf ft)

3.5Recharging the battery (All 250/300 models)

Warning

Risk of injury Battery acid and battery gases cause serious cauterization.

–Keep batteries out of the reach of children.

–Wear suitable protective clothing and goggles.

–Avoid contact with battery acid and battery gases.

–Keep the battery away from sparks or open fire. Charge only in well ventilated rooms.

–Flush with copious amounts of water in case of skin contact. If battery acid comes into contact with the eyes, flush the

eyes with water for at least 15 minutes and consult a physician.

Warning

Environmental hazard Battery parts and acid are harmful to the environment.

–Do not discard batteries with the household trash. Dispose of a defective battery in an environmentally compatible manner.

Give the battery to your KTM dealer or to a recycling center that accepts used batteries.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Motocicleta de KTM

KTM

KTM Freeride E-XC 2021 Manual de usuario

KTM

KTM 2014 690 Enduro R EU Manual de usuario

KTM

KTM 990 ADVENTURE Manual de usuario

KTM

KTM 1190 RC8 Manual de usuario

KTM

KTM 950 SUPERMOTO R Manual de usuario

KTM

KTM 350 XC-F Manual de usuario

KTM

KTM 990 Supermoto T Manual de usuario

KTM

KTM 450 SX-F 2017 Manual de usuario

KTM

KTM 640 LC4 Adventure Manual de usuario

KTM

KTM 450 EXC RACING 2006 Manual de usuario

KTM

KTM 125 EXC Manual de usuario

KTM

KTM 1190 RC8 R EU/UK 2009 Manual de usuario

KTM

KTM 450 EXC EU 2013 Manual

KTM

KTM 125 SX Manual de usuario

KTM

KTM 65 SX 2005 Manual de usuario

KTM

KTM 2015 RC 390 EU Manual de usuario

KTM

KTM 1190 Adventure R EU Manual de usuario

KTM

KTM 1290 Super Duke R 2017 Manual

KTM

KTM 2015 200 Duke Manual de usuario

KTM

KTM 50 SENIOR ADVENTURE 2006 Manual de usuario

KTM

KTM 125 SX Manual de usuario

KTM

KTM 690 Enduro R Manual de usuario

KTM

KTM 790 ADVENTURE R 2022 Manual de usuario

KTM

KTM 400 EXC RACING Manual de usuario

Manuales populares de Motocicleta de otras marcas

OHVALE

OHVALE GP-0 Manual de lista de piezas

Yamaha

Yamaha Star XV19CTSZ 2009 Manual de usuario

HYOSUNG

HYOSUNG ST7 Manual de usuario

Husqvarna

Husqvarna FC 250 2016 Manual de usuario

Ducati

Ducati SCRAMBLER 800 Manual de instrucciones

MOTO GUZZI

MOTO GUZZI QUOTA 1100 ES Manual de usuario

APRILIA

APRILIA ETV MILLE CAPONORD - PART1 02-2001 Manual de usuario

Yamaha

Yamaha 2006 YZF-R1V Manual de usuario

Fantic

Fantic Enduro 125 Manual de usuario

Ducati

Ducati Supersport 750 desmodue Manual de usuario

MV Agusta

MV Agusta 2008 F4 312RR 1078 Manual de instrucciones

Yamaha

Yamaha XVS650A Manual de usuario

Yamaha

Yamaha YZF-R6T(C) Manual

Ducati

Ducati 748 monoposto strada Manual de usuario

ATK

ATK 1988 250 Manual de usuario

Excelsior-HENDERSON

Excelsior-HENDERSON 1999 HCX Manual de usuario

Triumph

Triumph Thunderbird Manual de usuario

Yamaha

Yamaha 2006 FJR1300A Manual de usuario