KROMA BM5309D13 Manual de usuario
Professional Monitors 9”
BM5309A12 (V.3-4)/A13
User Manual
BM5309D13
Edition 01
2002
KROMA T E L E C O M
Pol. Ind. Alcobendas - C/ La Granja, 80
28108 Madrid - ESPAÑA
Tel. (34-91) 661 45 14
Fax. (34-91) 484 03 49
www.kromatelecom.com
KROMA TELECOM PROFESSIONAL MONITORS BM5309
BM5309
1
WARNING: This product includes critical
mechanical and electrical parts which are
essential for X-Radiation safety.
For continued safety replace critical components
indicated in the service schematic only with exact
replacement parts given in the parts list of
service Manual.
Operating high voltage for this product is 16 Kv.
At minimum brightness. Refer to service
manual for measurement procedures and
proper service adjustments.
WARNING: Electric shock or fire hazard can
be caused if critical components are replaced
by non conform components. Refer to parts
list of service manual.
CAUTION: High vacuum tube is dangerous to
handle refer replacement to qualified personnel.
Replace with a tue of the same type for continued
safety
SAFETY INFORMATION
KROMA TELECOM PROFESSIONAL MONITORS BM5309
BM5309
0
1. INTRODUCTION
1.1. APLICATIONS
The KROMA BM5309 monitors have been designed to use in Broadcast studios for
signal evaluation requiring accurate picture reproduction. Also it can be used in post-
production..
They incorporate microprocessor based control in all its operations, providing
automatic color set-up, thus eliminating the operator´s subjetive factor.
1.1.1. FEATURES
BM5309A12 9"
Basic Video version: CCVS (PAL/NTSC). Three composite video inputs, one of
them is configurable as external sync.
Options:
BM5009X01
This module consist of 2 Digital video inputs in passive loop-through, according to
(ITU-R BT601) 10 Bits and analog components (RGB/YPrPb).
BM5009X02
This module consist of 2 Digital video inputs in passive loop-through, according to
(ITU-R BT601) 10 Bits and analog components (RGB/YPrPb). This SDI module
allows the user to extract the embedded audio and then output it in Analog or AES
EBU Digital form.
BM5309A13 9"
It can be configured with the following options:
BM5309X01
This module consist of 2 Digital video inputs in passive loop-through, according to
(ITU-R BT601)10 Bits
BM5309X02
This module consist of 2 Digital video inputs in passive loop-through, according to
(ITU-R BT601) 10 Bits. This SDI module allows the user to extract the embedded
audio and then output it in Analog or AES EBU Digital form.
BM5309X03
This module consist of 1 PAL,NTSC,SECAM video input and 2 Digital video inputs
in passive loop-through, according to (ITU-R BT601) 10 Bits
BM5309X04
It is the more complete version (module), it has all the options previously
mentioned.
KROMA TELECOM PROFESSIONAL MONITORS BM5309
BM5309
1
1.1.2. PICTURE TUBE
High resolution, in line guns an shadow mask tube, with 0.28 dot pitch and P22
phosphor.
1.1.3. COLOUR STABILITY
Beam current feedback, which allows to correct colour temperature drift caused by
CRT variation and environmenttal conditions.
1.1.4. FLEXIBILITY
Modular configuration. It is provided with an analog and digital bus, allowing the
exchange of signals between the options installed, making it a system of open
architecture for future options.
1.1.5. AUTO SETUP SYSTEM
By use of the KROMA set AK5400X50, composed by a DG5400 test signal
generator and an optical probe model SR5400.The generator is able to provide up
to 34 patterns designed for monitors alignment.
With this combination, automatic grey scale adjustment can by carried out.
This set also allows transfering automatically the parameter setting of this setup to
other monitors.
1.1.6. REMOTE CONTROL
The RS-485 bus included in the BM5309 KROMA monitors. Is able to control up to
128 monitors. These can be in group controlled, individually controlled or all of
them can be controlled at the same time by remote control RK5000.
1.1.7. MENU
This help the operation, displaying the operating parameters .and the commands
to access at several functions.
The adjustment operations to be done by the specialized personnel are protected
by numerical password.
1.1.8. NORMAL SIZE, UNDERSCAN AND 16:9
The BM5309 range provides facilities for normal picture size or underscan (95%
reduced size) and aspect ratio 4:3 and 16:9 selectable from the front panel by
SIZE key.
1.1.9. MEMORIES
The monitor has 5 available memories
•All memories accessible via password (only for data store)
•Four memories for general use.
•One memorie for the system or factory
KROMA TELECOM PROFESSIONAL MONITORS BM5309
BM5309
2
1.2. TECHNICAL SPECIFICATIONS
1.2.1. SCAN & SYNC
Systems 625/50/2:1 Horizontal frequency 15.625 Hz
525/60/2:1 Horizontal frequency 15734 Hz
Horizontal oscillator lock-in range: ±750 Hz
Horizontal sync. constant time: Fast: 0.5 mS
Slow: 2.5 mS
1.2.2. PICTURE DISPLAY
Aspect ratio: 4:3 and 16:9
Errors: - Linearity error: ≤4 % of picture height
- Geometry error: ≤1 % ídem.
- Convergene error:
TUBE ZONE 1 REST
9” 0.4 mm 0.5 mm
ZONE 1 IS WITHIN A CIRCLE CENTRED ON THE SCREEN WHOSE DIAMETER IS EQUAL TO PICTURE HEIGHT.
1.2.3. CTR
•9” HR 0.28 dot pitch Phosphor: P22
•Resolutión : > 450 TV línes a centre
•Colour temperature: 6500º K ±200º K (IN ALL MEMORIES)
•Black level: Set to 0.5 Nit (10 % APL WINDOW SIGNAL)
•White level: Set to 90 Nit (100% APL WINDOW SIGNAL)
•Beam current limiting: 180 Nit (FLAT FIELD SIGNAL)
1.3. BM5309A12 MODEL
1.3.1. DECODER PAL / NTSC PERFORMANCE
•Inputs A, B and C
♦Level : 1 Vpp +3/-6 dB
♦Impedance : 75 Ω±1% or loop-through (selectable)
♦Return losses: 35 dB @ 5 Mhz.
♦Isolation between A, B and C inputs: > 60 dB @ 10 Mhz.
♦Mismatch between A and B inputs: < 1% and < 1º @ 4.43 Mhz
•External sync input
♦Level : 4 VPP +6 dB / -28 dB
♦Impedance : 75 Ω±1% or loop-through (selectable)
♦Return losses: > 35 dB @ 5 Mhz
KROMA TELECOM PROFESSIONAL MONITORS BM5309
BM5309
3
•Auxiliary signal (Front panel)1
♦Format : CCVS similar to A and B
♦Impedance : 75 Ω±1%
♦Return losses: > 25 dB @ 5 Mhz.
1.3.2. LUMINANCE
•Frequency response:
Without notch filter: 100 Khz - 6 Mhz ±1 dB
Notch filter suppresion < - 30 dB @ 4.43 Mhz
•K factor
(APERTURE 0 dB) WITHOUT FILTER WITH FILTER
Kpb < 0.5 % < 1%
K2T < 0.3 % < 1.2%
•Non linearity: < 1%
•Noise: (100 Khz - 5 Mhz) < 60 dB
1.3.3. CHROMINANCE
•Saturation control: ±6 dB
•Subcarrier oscillator lock.in range: 300 Hz
•Luminance-crominance delay : < 50 nS
1.4. BM5309A13 MODEL
1.4.1. SDI FEATURES
Compatible with signal source according to norm ITU-R BT.601 and BT.656
SMPTE/EBU of 270 Mbits per second.
♦Demultiplexed of components and synchyronization according to Rec.601 and
Rec.656 of CCIR.
♦S1 and S2 video inputs in loop-through. Impedance 75Ω
♦Return losses: > 21 dB @ 270 Mhz. or loop-through (selectable)
♦Frequency response: 0 – 5,5 Mhz. < 0.5 dB
♦Tilt (V): < 0,5 %
♦K factor: Kp < 0,3 %
Kpb < 0,2 %
♦Non lineality: < 1%
1During the auto set-up it control the channels R G B in parallel.
KROMA TELECOM PROFESSIONAL MONITORS BM5309
BM5309
4
♦Missmatch between components:
Gain: < 0.1%
Delay: < 3 ns
♦Analog audio levels: (Only in BM5309X02 and BM5309X04)
4Vpp @ 0dBFs
Nota: The audio outputs are not designed to work with 4 or 8 Ohm loads, it must be
connected to inputs with loads >1K Ohm.
1.4.2. DECODER PAL / NTSC / SECAM PERFORMANCE
♦Input A
♦Level : 1 Vpp +3/-6 dB
♦Impedance : 75 Ω±1% or loop-through (selectable)
♦Return losses: 35 dB @ 5 Mhz.
♦Isolation between A, B and C inputs: > 60 dB @ 10 Mhz.
♦Mismatch between A and B: < 1% and < 1º @ 4.43 Mhz
♦External sync input
♦Level : 0.3 VPP (Black burst) +6 dB / -28 dB
♦Impedance : 75 Ω±1% or loop-through (selectable)
♦Return losses: > 35 dB @ 5 Mhz
♦Auxiliary Input (Front panel)2
♦Format : CCVS similar to A and B
♦Impedance : 75 Ω±1%
♦Return losses: > 25 dB @ 5 Mhz
1.4.3. LUMINANCE
♦Filter: By “Comb filter” adaptive PAL/NTSC of three lines.
♦Frequency response: 100 Khz – 5.5 Mhz ±1 dB
♦K factor: Kpb < 2%
K2T <3.5%
♦Differential Gain: 2º
♦Differential Phase: 2%
2During the auto set-up it control the chanel R G B in parallel.
KROMA TELECOM PROFESSIONAL MONITORS BM5309
BM5309
5
1.4.4. CHROMINANCE
•Saturacion control: ±6 dB
•Subcarrier oscillator lock in range: 300 Hz
•Luminance-chrominance delay: < 50 Ns
1.4.5. GENERAL
Enviromental Characteristics:
♦Warm-up : 20 minutes to meet specifications.
♦Temperature range:
From 15 to 40 ºC (TO MEET SPECIFICATIONS)
From 0 to 45 ºC (OPERATING ONLY)
♦Relative humidity: 0 to 90 % non considensing @ 40 ºC
♦Altitude : ≤3000 m.
♦X-ray emision: < 0.1 mR/Hr @ 5 cm monitor outside surface.
•Power
♦Voltage : 110 / 220 VAC ±20%
♦Power consumption: 45 W
•Dimensions:
Height Width Depth
Model 9” 218 mm. (5 UR.) 222 mm. 420 mm.
•Weight : 8 Kg.
1.5. INSTALLATION
1.5.1. Previous Inspection
After having removed the equipment from its original packing material, check for
visible signs of damage which may have occurred during shipment. Report any
shortage or damage to the freight carrier and KROMA or its representative
inmediately.
Check that you have received the following accessories with the monitor:
•AC power cord, and
•User´s Manual.
If the equipment has to be reshipped to a long distance, it is recommended to use
the original packing material in order to avoid damages during transport.
KROMA TELECOM PROFESSIONAL MONITORS BM5309
BM5309
6
1.5.2. Safety Information
For electric shock protection, it is necessary to connect the chassis to a protective
ground; to this purpose, the earth ground terminal of the plug is directly connected
to the metal part of the monitor (green-yellow wire). Insert the power plug in a
mating outlet with an earth ground contact.
Due to the presence of high voltages inside the equipment, the same can only be
open, adjusted or repaired by QUALIFIED PERSONNEL.
1.5.3. Connection to the Main
Before connecting the monitor to the mains, check that the mains voltage
corresponds to that indicated in the voltage selector located in the rear panel, next
to the mains connector.
If the mains voltage presetting is not the appropriate, carry out the change by
removing the fuseholder and turning it until the desired value is shown in the
window.
Fuses should be changed in accordance with the mains voltage presetting used, as
per the following table:
POWER FUSE
220 V 2.5 A Slow
110 V 3.15 A Slow
1.5.4. Location
Due to the CRT´s sensitivity to magnetic fields, avoid installing the monitor near this
type of disturbance sources such as: Loudspeakers, electric motors, transformers,
etc.
The monitor has a dagaussing device incorporated which operates automatically
when the equipment is switched on. It can also be activated manually from the front
panel controls.
If the monitor is changed of location, some colour impurities may occur due to the
variation of the earth magnetic field. This problem disappears by activating the
degaussing circuit with the DEG key.
During the time this operation last, avoid placing near the monitor items which have
magnetic information such as: tapes, cassettes, cards, etc.
1.5.5. Tally Lamp
This lamp, located on the monitor´s front panel, can be activated with voltages
within the range + 24V and + 48 V, or by closing of the contacts 2 and 3 of the
connector located in rear panel. (SEE FIGURE).
KROMA TELECOM PROFESSIONAL MONITORS BM5309
BM5309
7
1.5.6. Ground Terminals
There are two ground terminals: protective ground and electrical earth or ground
from the power supply. They are normally connected by means of a metal jumper,
but they can be isolated one another by eliminating said jumper, in case it is
necessary to avoid hum pickups due to the installation.
1.5.7. Remote Control Connectors (RS-485 Interface)
They are located at the rear of the video unit. The connectors, in loop through
configuration, are prepared for connection of the KROMA RK-5400 remote
control.This connector, are also useful for to update the futures software versions
Configuration
Terminal 1 - S/C
“ 2 - DATA + (RS485)
“ 3 - RX (RS232)
“ 4 - GND
“ 5 - S/C
“ 6 - TX (RS 232)
“ 7 - DATA - (RS 485)
“ 8 - GND
REM
Figure 1
Tabla de contenidos
Otros manuales de Monitor de KROMA
