Kreg Micro-Pocket Drill Guide Kit 730 Manual de usuario
English 2
French 11
Spanish 21
OWNER’S MANUAL
We’re here to help.
We want you to have an exceptional project building experience.
If you have questions or need support, please get in touch.
Tell us about your experience.
Your opinion counts. And we’re always looking for ways to
improve. Share your feedback so we can keep growing and
innovating for you. www.kregtool.com/feedback
WARNING Every user must read and follow instructions and safety
precautions in this manual. Failure to do so could result in serious injury.
Save manual for future reference.
Kreg Micro-Pocket™ Drill
Guide Kit KPHA730
2
Safety Precautions
WARNING Before using a power tool with this product, read and follow the
tool manufacturer’s instructions and safety precautions in addition to the safety
precautions below to reduce the risk of serious injury from hazards such as re,
electric shock, or rotating drill bit.
■Always wear personal protective equipment recommended by the
manufacturer of the power tool you are using, such as eye, hearing, or
respiratory protection.
■The drill bit is sharp. Handle with care.
■Do not allow familiarity gained from frequent use of your tools to replace
safe work practices. A moment of carelessness is sufcient to cause
serious injury.
■Avoid awkward hand positions where a sudden slip could cause contact
with the rotating bit.
■When drilling, always ensure that the workpiece is clamped securely. It is
dangerous to hold the workpiece in place by hand.
WARNING Do not operate this tool or any machinery while under the inuence
of drugs, alcohol, or medications.
WARNING This product can expose you to chemicals including Acrylonitrile
and other chemicals, which are known to the State of California to cause
cancer and reproductive harm. For more information go to
www.P65Warnings.ca.gov.
Table of Contents
Safety Precautions . . . . . . . . . 2
Pre-Installation/Pre-Assembly. . . 3
Assembly/Setup . . . . . . . . . .4
Operation – Drilling Your First
Pocket Hole . . . . . . . . . . . . 5
Operation – Drilling and Driving
Pocket-Hole Screws . . . . . . . . 7
Accessories . . . . . . . . . . . . 9
3
Pre-Installation/Pre-Assembly
Review this section before you begin. Ensure you have all parts listed below.
If any item appears missing or lost, do not use this product. Contact Technical
Support or return product to place of purchase.
A
C
B
D
Part Description
A KPHA730 Kreg Micro-Pocket™ Drill Guide
B Easy-Set Micro-Pocket Drill Bit
C Material Thickness Gauge/Hex Wrench
D Easy-Set Micro-Pocket Stop Collar
4
Assembly/Setup
a. Remove existing drill guide from the Kreg Jig 720 by squeezing the tabs
(1) on both sides and lifting forward and up to remove the drill guide from
the carriage of the Kreg Jig 720.
b. Insert the Micro-Pocket Drill Guide (A) into the carriage by squeezing
the tabs (1) on both sides of the drill guide carriage, inserting the bottom
tab of the Micro-Pocket Drill Guide (A) into the slot on the carriage and
pressing the top of the Micro-Pocket Drill Guide (A) into place.
1
A
The following steps are the same as using the standard size drill guide. See
Owner’s Manual for detailed instruction on the following steps.
5
Operation – Drilling Your First Pocket
Hole
1 Determine the Material Thickness and Set the
Stop Collar
a. Use the material thickness gauge (C) to determine the material thickness
range.
b. Set the stop collar (D) by placing it on the drill bit (B) and aligning
the window of the stop collar (D) with the material thickness range
determined in step a.
c. Use the hex wrench (C) to lock the stop collar (D) into place on the drill
bit (B).
B
C
D
6
2 Position your Workpiece
There are two different methods for aligning your Kreg Jig with your workpiece:
■For a workpiece narrower than 1-1/4" wide it is recommended to place
each pocket hole 3/8" from the edge, if possible. To do this, mark 3/8" from
each edge as the center of the pocket hole and align one of the numbered
pocket-hole drill guides (number 1, 2, or 3) and drill the rst pocket hole.
Then, re-position to the second mark and repeat the drilling process.
■For a workpiece between 1-1/4" to 2-1/4", use the board centering mark A
and drilling pocket-holes 1 and 2.
■For a workpiece between 2-1/4" and 3-1/2", use board centering mark B
and drilling pocket-holes 1, 2, and 3.
■For wider workpieces such as a drawer box side, it is recommended
that the pocket-holes be spaced at 3/4" center-to-center spacing. For
workpieces such as panels, it is recommended that the pocket-hole
spacing be 1/2" to 1-1/4" from the edge and then every 4" to 6".
1 2 3 A B C
Board Width Center Mark Drill Guide
1-1/4" to 2-1/4" A 1 and 2
1-1/4" to 2-1/4" C 2 and 3
2-1/4" to 3-1/2" B 1, 2, and 3
Press down on the jig handle in one smooth motion until the jig handle is at
its travel limit. Proceed to the Operation - Drilling and Driving Pocket-Hole
Screws section to start drilling.
7
Operation – Drilling and Driving
Pocket-Hole Screws
1 Drill Pocket Holes
WARNING When drilling, always ensure that the workpiece is clamped
securely and that the jig handle is pressed down to its travel limit.
a. Place your prepared drill bit (B) with stop collar (D) into your drill.
b. Insert your drill bit (B) into the drill guide (1) and bring your drill up to
speed before contacting the workpiece to ensure correct rotation of the
drill bit.
c. Drill until the stop collar (D) stops going any deeper due to contact
between the stop collar (D) and drill guide (1). Remove the drill bit (B) from
the drill guide (1) while the drill bit is still rotating.
d. When you are nished drilling pocket hole(s), lift the jig handle to release
the clamping pressure; then remove your workpiece.
B
D
1
8
2 Drive Screws
a. Your Micro-Pocket™ Drill Guide Kit is designed to work with SPS type
screw heads. Ensure you are using the correct screw size according to
this chart:
Gauged Material
Thickness
Easy-Set
Stop Collar
Material
Thickness Stop
Screw Length
1/2 Range 1/2 1/2 1" (25 mm)
3/4 Range 3/4 3/4 1-1/4" (32 mm)
3/4 3/4 1-1/2" (38 mm)
1-1/2 Range 1½ 1½ 2-1/2" (64 mm)
For more information on screw selections, go to www.Kregtool.com/
Screws or simply scan the QR code on the side of your sample screw
package.
Note For some material in the 1/2" range, it may be necessary to use
the SPS-F075 screw to prevent the tip of the screw from exiting the
workpiece.
Note If your material thickness falls in the range, use the same
setup techniques as the 3/4" range with a 1-1/2" screw.
b. Clamp joints in place to ensure a better nished joint. These examples
show face joints and edge joints.
9
2 Drive Screws (continued)
WARNING When drilling, always ensure the workpiece is clamped securely.
c. Place your screw on your driver tip, position the screw in the pocket hole,
and drive the screw until it is fully seated without overdriving.
Accessories
KPHA750 Pocket-Hole Jig Docking Station
06/2020 104694 V1
EXPLORE. BUILD. SHARE.
We’re makers just like you.
That’s why we love to see what you’re working on.
Share with the community and get inspired!
#madewithKreg
Get free plans, project resources, and more.
kregtool.com and buildsomething.com
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Idiomas:
Otros manuales de Accesorios para herramientas eléctricas de Kreg
Kreg
Kreg Klamp Vise KKS1050 Manual de usuario
Kreg
Kreg Micro-Pocket Drill Guide Kit 530 Manual de usuario
Kreg
Kreg Precision Router Lift Manual de usuario
Kreg
Kreg KBK-IP Manual de usuario
Kreg
Kreg KMS7215 Manual de usuario
Kreg
Kreg Swing Stop KMS7801 Manual de usuario
Kreg
Kreg KPHJ310-INT Manual de usuario
Kreg
Kreg KMA4100 Manual de usuario
Kreg
Kreg Straight Edge Guide Manual de usuario
Manuales populares de Accesorios para herramientas eléctricas de otras marcas
ADAMAS
ADAMAS B32 Manual de usuario
STEINEL PROFESSIONAL
STEINEL PROFESSIONAL 4007841009595 Manual de usuario
Echo
Echo Speed-Feed Universal 400 LH/RH Manual de usuario
SCHUNK
SCHUNK ROTA TB-TBS-EP Instrucciones de uso
Schmid
Schmid RAPID Secure XL Manual de usuario
Drill Master
Drill Master 360X Manual de usuario
