Kramer VM-4DT Manual de usuario

-4DT Quick Start (P/N: 2900-300799QS REV 1)

P/N:

2900- 300799QS

Rev:

Scan for full manual

VM-4DT Quick Start Guide

This guide helps you install and use your VM-4DT for the first time.

Go to www.kramerav.com/downloads/VM-4DT to download the latest user manual and check if firmware

upgrades are available.

Step 1: Check what’s in the box

VM-4DT

1:4 HDBT Distributor 1 Power supply (5V DC)

1 Quick start guide

4 Rubber feet

Step 2: Get to know your VM-4DT

# Feature Function

1 ON LED Lights green when the unit receives power

2 PROGRAM Mini USB Connector Use to send RS-232 commands. Connect to a PC to perform firmware upgrades (via

K-Upload) and work with the EDID Designer. K-Upload and EDID Designer can be

downloaded from our Web site at:www.kramerav.com/manual/EDID Designer

EDID SETUP Button

Press to capture the input EDID, force RGB mode or select the default EDID

4 ACTIVE INPUT LED Lights green when an HDMI signal is embedded on the HDBaseT input

HDBT LINK LEDs IN Lights green when a link is established with the HDBaseT transmitter

OUT

Lights green when a link is established with the HDBaseT receiver (from 1 to 4)

6 OUTPUTS CONNECTED LEDs Lights green when an acceptor (sink) is detected on the HDBaseT receiver connected to

the output (from 1 to 4)

7 INPUT HDBT Connector Connects to an HDBaseT source, for example

TP-580T

8 HDBT OUT Connectors Connect to an HDBaseT acceptor (from 1 to 4), for example

TP-580R

SETUP 8-way DIP-switches

Use to set IR (DIP-switches 1-4) and RS-232 (DIP-switches 5-8) command behavior

SETUP 4-way DIP-switch

For future use

11 5V DC +5V DC connector for powering the unit

Step 3: Install the VM-4DT

To mount the VM-4DT in a rack, use an RK-1 rack adapter. Alternatively, attach the rubber feet to the underside of the VM-4DT and

place it on a table.

Step 4: Connect the inputs and outputs

Always switch OFF the power on each device before connecting it to your VM-4DT. For best results, we recommend that you always

use Kramer high-performance cables to connect AV equipment to the VM-4DT.

RJ-45 Pinout:

DIP-Switch Setup:

For HDBaseT connectors:

Note: By default, all DIP-

switches are set to OFF (up).

PIN EIA /TIA 568B

PIN Wire Color

Orange / White

2 Orange

3 Green / White

Blue

5 Blue / White Out # IR Routing is enabled when: RS-232 Routing is enabled when:

Green

OUT 1

DIP 1 – OFF (up)

DIP 5 – OFF (up)

7 Brown / White OUT 2 DIP 2 – OFF (up) DIP 6 – OFF (up)

OUT 3

DIP 3 – OFF (up)

DIP 7 – OFF (up)

OUT 4 DIP 4 – OFF (up) DIP 8 – OFF (up)

Step 5: Connect the power

Connect the power adapter to the VM-4DT and plug the adapter into the mains electricity.

Safety Instructions

Caution:

There are no operator serviceable parts inside the unit.

Warning:

Use only the Kramer Electronics power supply that is provided with the unit.

Warning:

Disconnect the power and unplug the unit from the wall before installing.

See www.KramerAV.com for updated safety information.

Step 6: Acquire the EDID

To acquire an EDID, press the EDID SETUP button as follows:

1. Press the EDID SETUP button once.

The OUTPUTS CONNECTED LEDs flash to indicate the current EDID used: 1, 2, 3, 4, or all if the default EDID is currently

used.

2. Press the EDID SETUP button again to enter the EDID read mode and then press repeatedely to cycle through the EDID

source options until the desired EDID source is reached: OUT 1 -> OUT 2 -> OUT 3 -> OUT 4 -> all LEDs flash (for a default

EDID).

3. Wait a few seconds for the VM-4DT to read the EDID.

When complete, all LEDs display the present output connection status.

Otros manuales para VM-4DT

Otros manuales de Convertidor de medios de Kramer

Kramer

Kramer VP-501N Manual de usuario

Kramer

Kramer FC-10Dxl Manual de usuario

Kramer

Kramer VP-418 Manual de usuario

Kramer

Kramer VM-16HDMI Manual de usuario

Kramer

Kramer VP-426 Manual de usuario

Kramer

Kramer VM-30CA Manual de usuario

Kramer

Kramer VP-740 ProScale Manual de usuario

Kramer

Kramer VP-426H2 Manual de usuario

Kramer

Kramer VM-2DH Manual de usuario

Kramer

Kramer VP-505 Manual de usuario

Kramer

Kramer VM-2DH Manual de usuario

Kramer

Kramer FC-331 Manual de usuario

Kramer

Kramer KDS-10 Manual de usuario

Kramer

Kramer FC-10 Manual de usuario

Kramer

Kramer PT-1H Manual de usuario

Kramer

Kramer VP-701XL Manual de usuario

Kramer

Kramer FC-7501 Manual de usuario

Kramer

Kramer VP-715 Manual de usuario

Kramer

Kramer VS-411UHD Manual de usuario

Kramer

Kramer FC-17 Manual de usuario

Kramer

Kramer VP-436N Manual de usuario

Kramer

Kramer VP-419XL Manual de usuario

Kramer

Kramer VP-434 Manual de usuario

Kramer

Kramer 575 Manual de usuario

Manuales populares de Convertidor de medios de otras marcas

SoundTraxx

SoundTraxx Blunami BLU-2200 Manual de usuario

SPROLINK

SPROLINK VA1 Manual de usuario

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manual de usuario

Nikon

Nikon AF-S TC-20E III Manual de usuario

Axis

Axis AXIS Q7406 Manual de usuario

Omega

Omega TAC80B-J Manual de usuario

Zoom

Zoom Thunderbolt TAC-2R Manual de usuario

OST

OST iConverter 10/100M Manual de usuario

Vertiv

Vertiv Netsure Manual de usuario

birddog

birddog MINI Manual de usuario

Roland

Roland GI-10 Manual de usuario

Wallenstein

Wallenstein WX310 Manual de usuario

Pace

Pace MSS 200-1 Manual de usuario

Solar Converters

Solar Converters EQ 12/24-50 Manual de usuario

CYP

CYP EL-7400V Manual de usuario

TIE

TIE MIDI 1i1o Manual de usuario

DCS

DCS Vivaldi Upsampler Manual de usuario

Westermo

Westermo MCW-211 SERIES Manual de usuario