KOTA EVO Manual de usuario
USER ManUal
Furnace eVO
Dear user,
Thank you very much for choosing a KOTA product.
KOTA produce equipment with high quality materials seeking to guarantee
the confidence and safety of its products.
To maintain the perfect functioning of your EVO Oven, some basic care
is necessary. Read this manual carefully and follow the instructions for
installation and use.
Safety precautions
• Use original KOTA products identied by the brand, which guarantee
the best performance for your equipment.
• Do not modify the equipment or request third parties to do so, except
when specifically KOTA authorize it, as performance and / or security
could be compromised. Any alteration of the product without
previous authorization will imply the loss of the guarantee.
• Do not use extensions or any type of connector between the power
cord of the appliance and the socket. Procedures such as these
could decrease the performance of your equipment and increase
your energy consumption.
• For cleaning, use only a damp cloth. Do not apply abrasive, solvent
or corrosive products on the equipment.
Safety precautions
• Do not place work removed from the oven directly on the glass at the
base of the work area. Coatings or porcelain freshly removed from the
equipment can cause cracks in the glass base.
Maximum temperature over the glass: 200ºC.
• When turn on the equipment, place the refractory base on the
aluminium tray. If do not perform this procedure so the rubber seal ring
could be damaged.
Index
Features................................................................................................... 5
Technical data.......................................................................................... 5
Equipment overview.................................................................................6
Initial set up............................................................................................. 6
Selecting & editing firing programs..........................................................8
Pressing programs....................................................................................16
Setting up press mode............................................................................. 18
Warranties terms and scope..................................................................... 19
• Multilanguage function.
• Tempered glass base.
• High temperature accuracy.
• Oven with top nish in brushed stainless steel.
• Temperature sensor (Platen / Rhodium).
• Mufe for burning with (Quartz clear).
• Intelligent dynamic electronic injection.
• 80 Fire programs & 20 Press programs.
• Linear heating speed from 20 ° to 120 °C per minute.
110 or 220V equipment power supply (Check Furnace voltage).
Maximum consumption: 1300-Watts.
Fuse: 20A.
Maximum current of the vacuum pump intake: 10A.
Maximum operating temperature: 1200 °C.
Height: 542mm
Width: 298mm
Depth: 420mm
Net weight: 17kg
Gross weight: 19.2kg
Frequency: 50-60Hz
Colour: Back with brushed stainless steel nishes
Features
Technical data
5
Equipment overview
• 1º: Before turning ON check if the voltage is correct with the equipment
voltage and then connect EVO Oven to AC power socket.
• 2º: Place the refractory plate on the aluminium tray of the Kota EVO
Initial set up
Fuse 20AElectrical connection
for the vacuum pump
Connection
for vacuum
hose
Refractory plate
Press ring
Aluminium tray
Base glass
Power cable
Main switch
ON/OFF
6
• 3º: Connect the Vacuum Pump power cable to electrical connector
located on the back of the unit as shown in the illustration on page 3.
Check the main voltage.
The Vacuum Pump voltage must be the same as that of the oven.
• 4º: Turn on the Main Switch of the EVO that is located on the right side of
the oven as shown in the illustration on page 4. When the EVO is turn on
the LCD will show the initial screen, as shown below:
Press “EDIT “to set the language selection.
• The languages Portuguese, English and Spanish are available.
To return to the “TYPE OF PROGRAM” MENU, press the “EDIT” key.
SAFETY INSTRUCTIONS
STAND-BY MODE
The Stand-by mode serves to prevent peripheral heating of the oven
and to save energy.Whenever the oven remains unused for more than
ve minutes, the mufe will close. To open the mufe press
the “EXECUTE” key.
• Do not place work removed from the oven directly on the glass at the
base of the work area. Coatings or porcelain freshly removed from the
equipment can cause cracks in the glass base.
Maximum temperature over the glass: 200ºC.
• When Turn On the equipment, place the refractory base on the
aluminium tray. If do not perform this procedure so the rubber
seal ring could be damaged
7
Selecting and editing a firing program
When selecting the ring program the following information will be on the
screen:
On this screen, it is possible to move the lift up, down and stop in
any position manually.
Just press the left directional arrow to perform the two functions.
The ring programs range from number 1 to 80.
There are 33 ring programs inserted by the manufacturer that
go from number 1 to 33.Those programs can be modied according
to the instructions detailed below:
To edit a ring program, select a program number, and then press, “EDIT”.
When press the “EDIT”key screens will be appear in the following order:
INITIAL TEMPERATURE (TP1)
The initial temperature is the initial temperature of the firing process.
Inicial temperature
Number of the program selected
8
DRYING TIME (TSEC)
The drying time is the waiting period to the start of the closing stage
of the mufe.
RISE TIME (TSUB)
The closing time of the mufe can be adjusted to close directly or
for a specic time between 00:40 seconds and 30:00 minutes.
To activate the direct closing adjust the parameters in 00:00
PRE-FIRING TIME (TPRE)
The PRE-FIRING time starts when the rise time reached 90%
of the course.
The elevator remains in the position by the programmed time and then
the mufe will close.
9
DOWNING TIME (TDES)
The downing time is activated after the last ring process be executed
and can be adjusted for direct opening or for a determined time between
00:40 seconds and 30:00 minutes.
To activate the direct opening, set the parameters to 00:00.
BASE TEMPERATURE (TP2)
It is the next temperature level after the initial temperature.
HEATING RATE (TR2)
It is the heating rate between the initial temperature and the base
temperature 2.
The parameters can be adjusted from 20 ° to 120°C per minute.
10
Tabla de contenidos
