Kontron X-Board UPA 63036 Manual de usuario

Kontron Embedded Modules GmbH

Flatpanel Solutions

Marschnerstieg 7

22081 Hamburg / Germany

Fon: +49 (0)40 20 00 90-0

Fax: +49 (0)40 20 00 90-10

http://www.kontron-emea.com/flatpanel

X-BOARD-UPA

08.09.2004 1

X-BOARD-UPA

Universal Panel Adapter

Part-No. : 63036

Technical Manual (Preliminary!)

Table of Contents

1.0 General Information and Important Notes

2.0 Technical Information Summary

3.0 Configuration

4.0 Connectors

5.0 Layout

6.0 Schematic

7.0 Application Notes

8.0 Technical Specification

9.0 Technical Support

10.0 Revision History

Kontron Embedded Modules GmbH

Flatpanel Solutions

Marschnerstieg 7

22081 Hamburg / Germany

Fon: +49 (0)40 20 00 90-0

Fax: +49 (0)40 20 00 90-10

http://www.kontron-emea.com/flatpanel

X-BOARD-UPA

08.09.2004 2

1.0 User Information

Solutions, Hamburg

In this document Kontron Embedded Modules GmbH, Division Flatpanel

Solutions, Hamburg will also be referred to by the short form “KEM GmbH”.

The information in this document has been carefully checked and is

believed to be accurate and reliable. However, no responsibility is

assumed for inaccuracies. Furthermore, KEM GmbH reserves the right to

make changes to any portion of this manual to improve reliability, function

or design. KEM GmbH does not assume any liability for any product or

circuit described herein.

1.1 Trademarks

AT and IBM are trademarks of International Business Machines.

XT, AT, PS/2 and Personal System/2 are trademarks of International

Business Machines Corporation.

Microsoft is a registered trademark of Microsoft Corporation.

Intel is a registered trademark of Intel Corporation.

All other products and trademarks mentioned in this manual are

trademarks of their respective owners.

The reproduction, transmission or use of this document or its contents is

not permitted without expressed written authority.

Offenders will be liable for damages. All rights created by patent grant or

registration of a utility model or design, are reserved.

1.2 General

For the circuits, descriptions and tables indicated no responsibility is

assumed as far as patents or other rights of third parties are concerned.

The information in the Technical Descriptions describes the type of the

boards and shall not be considered as assured characteristics.

The reproduction, transmission or use of this document or its contents is

not permitted without express written authority. Offenders will be liable for

damages. All rights, including rights created by patent grant or registration

of a utility model or design, are reserved.

Kontron Embedded Modules GmbH

Flatpanel Solutions

Marschnerstieg 7

22081 Hamburg / Germany

Fon: +49 (0)40 20 00 90-0

Fax: +49 (0)40 20 00 90-10

http://www.kontron-emea.com/flatpanel

X-BOARD-UPA

08.09.2004 3

1.3 Warranty

Each board is carefully and thoroughly tested before being shipped. If,

however, problems should occur during the operation, please check your

user specific settings of all boards included in your system. This is often

the source of the fault. If a board is defective, it can be sent to your supplier

for repair. Please take care of the following steps:

- The board returned should correspond to the factory default

settings since a test is only possible under these settings.

- In order to repair your board as fast as possible, we require some

additional information from you. Please fill out the attached Repair

Form and include it with the defective board.

- If possible, the board will be upgraded to the latest version without

additional cost.

- Upon receipt of the board, please be aware that your user specific

settings were changes during the test.

Within the guarantee, the repair is free as long as the guarantee conditions

were kept. If no fault has been found, you will be charged with the test cost

due to the high test expenditure. Repairs outside of the guarantee will be

charged.

This KEM GmbH product is warranted against defects in material and

workmanship for our guaranteed warranty period from the date of

shipment. During the warranty period, KEM GmbH will, at its option, either

repair or replace products which prove to be defective.

For warranty service or repair, the product must be returned to a service

facility designated by KEM GmbH.

The foregoing warranty shall not apply to defects resulting from improper or

inadequate maintenance or handling by buyer, unauthorized modification

or misuse, operation outside of the environmental specifications for the

product, or improper installation or maintenance.

KEM GmbH will not be responsible for any defects or damages due to a

faulty KEM GmbH product other than the products supplied by

KEM GmbH.

Kontron Embedded Modules GmbH

Flatpanel Solutions

Marschnerstieg 7

22081 Hamburg / Germany

Fon: +49 (0)40 20 00 90-0

Fax: +49 (0)40 20 00 90-10

http://www.kontron-emea.com/flatpanel

X-BOARD-UPA

08.09.2004 4

2.0 Technical Information Summary

X-Board-UPA is an Evaluation Board (only for development) for VGA,

SVGA, XGA type TFT flatpanels to Kontron JILI interface with digital output

option.

CAUTION : Don´t connect this cable to a JILI Interface with LVDS output!

This can cause permanent damage to all connected devices!

3.0 Configuration

The X-Board-UPA is configured with +3,3V DC for the flat panel power

supply and +12V DC for the backlight power supply.

3.1 Configuration SW1

Configuration: Function:

Dip 1 Inverts the Data Enable signal

ON = not invert, OFF = invert

Dip 2 Inverts the V-Sync signal

ON = not invert, OFF = invert

Dip 3 Inverts the Panel Data Clock signal

ON = not invert, OFF = invert

Dip 4 Inverts the H-Sync signal

ON = not invert, OFF = invert

Dip 5 Select Data mapping

ON = U5 active, OFF = U6 active

Dip 6 Not function

3.2 Configuration SW2

Configuration: Function:

Dip 1 Programmable strobe select, only for LVDS output

ON = Rising edge strobe, OFF = Falling edge strobe

Dip 2 Vertical display mode select signal, only for X7

ON = U/D low, OFF = U/D high

Dip 3 Horizontal display mode select signal, only for X7

ON = R/L low, OFF = R/L high

Dip 4 VGA/QVGA mode select signal, only for X7

ON = Q/V low, OFF = Q/V high

Dip 5 Power for serial eeprom (JILI File)

ON = enable eeprom, OFF = disable eeprom

Dip 6 Power for D/A converter (Backlight dimming control, only for X9)

ON = enable D/A converter, OFF = disable D/A converter

Kontron Embedded Modules GmbH

Flatpanel Solutions

Marschnerstieg 7

22081 Hamburg / Germany

Fon: +49 (0)40 20 00 90-0

Fax: +49 (0)40 20 00 90-10

http://www.kontron-emea.com/flatpanel

X-BOARD-UPA

08.09.2004 5

3.3 Configuration panel power supply JP1

Only for X3, X6, X7

Configuration: Function:

1-2 shorted +3,3V DC Panel VCC

3-4 shorted + 5V DC Panel VCC

5-6 shorted + 12V DC Panel VCC

7-8 shorted Disable Panel Power Sequencing (only for debugging)

Caution ! Only one configuration (Panel VCC) for flatpanel is allowed,

otherwise the board is permanently damaged.

3.4 Configuration backlight power supply JP1

Only for X3, X9

Configuration: Function:

9-10 + 5V DC Backlight VCC

11-12 +12V DC Backlight VCC

13-14 Disable Backlight Power Sequencing (only for debugging)

Caution ! Only one configuration (Backlight VCC) for Backlight is

allowed, otherwise the board is permanently damaged.

Kontron Embedded Modules GmbH

Flatpanel Solutions

Marschnerstieg 7

22081 Hamburg / Germany

Fon: +49 (0)40 20 00 90-0

Fax: +49 (0)40 20 00 90-10

http://www.kontron-emea.com/flatpanel

X-BOARD-UPA

08.09.2004 6

4.0 Connectors

4.1 JILI – Digital Input connector X1

4.2 JILI – Interface connector X2

4.3 JILI40 - Interface connector X3

4.4 DIG30 - Interface connector X6

4.5 FLEX32 – Interface connector X7

4.6 Extern Power input (option) X8

4.7 Backlight connector X9

4.1 JILI – Digital Input connector X1

Flatfoil 40 Contacts, Right Angle, Bottom Contact

Case/Size: 0,5mm Pitch, Series: 6210 / ZIF

Description Name Pin

Pin Name Description

First Line Marker Vsync 1 O O 2 R0 Panel Data R0

Panel Data R1 R1 3 O O 4 ENAVDD Panel power enable

Panel Data R2 R2 5 O O 6 R3 Panel Data R3

Latch pulse Hsync 7 O O 8 R4 Panel Data R4

Panel Data R5 R5 9 O O 10 GND Power Ground

Panel Data G0 G0 11 O O 12 G1 Panel Data G1

Power Ground GND 13 O O 14 G2 Panel Data G2

Panel Data G3 G3 15 O O 16 JILI_DAT I2C Data

Panel Data G4 G4 17 O O 18 G5 Panel Data G5

I2C Clock JILI_CLK 19 O O 20 B0 Panel Data B0

Panel Data B1 B1 21 O O 22 /Detect Panel hot plug detection

Panel Data B2 B2 23 O O 24 B3 Panel Data B3

Power Ground GND 25 O O 26 B4 Panel Data B4

Panel Data B5 B5 27 O O 28 GND Power Ground

Data Clock SCLK 29 O O 30 DE Data Enable

+5,0V DC Power VCC 31 O O 32 VCC +5,0V DC Power

+5,0V DC Power VCC 33 O O 34 VCC +5,0V DC Power

Not connected NC 35 O O 36 GND Power Ground

Power Ground GND 37 O O 38 +12V +12,0V DC Power

+12,0V DC Power +12V 39 O O 40 +12V +12,0V DC Power

Kontron Embedded Modules GmbH

Flatpanel Solutions

Marschnerstieg 7

22081 Hamburg / Germany

Fon: +49 (0)40 20 00 90-0

Fax: +49 (0)40 20 00 90-10

http://www.kontron-emea.com/flatpanel

X-BOARD-UPA

08.09.2004 7

4.2 JILI - Interface connector X2

All JILI (JUMPtec Intelligent LVDS Interface ) signals are LVDS

compatible.

Flatfoil 40 Contacts, Right Angle, Bottom Contact

Case/Size: 0,5mm Pitch, Series: 6210 / ZIF

Description Name Pin

Pin Name Description

Not connected NC 1 O O 2 FTX0- Receiver Signal

Receiver Signal FTX0+ 3 O O 4 ENAVDD Panel power enable

Receiver Signal FTX1- 5 O O 6 FTX1+ Receiver Signal

Not connected NC 7 O O 8 FTX2- Receiver Signal

Receiver Signal FTX2+ 9 O O 10 GND Power Ground

Receiver Signal FTXC- 11 O O 12 FTXC+ Receiver Signal

Power Ground GND 13 O O 14 FTX3- Receiver Signal

Receiver Signal FTX3+ 15 O O 16 JILI_DAT I2C Data

Not connected NC 17 O O 18 NC Not connected

I2C Clock JILI_CLK 19 O O 20 NC Not connected

Not connected NC 21 O O 21 NC Not connected

Not connected NC 23 O O 24 NC Not connected

Power Ground GND 25 O O 26 NC Not connected

Not connected NC 27 O O 28 GND Power Ground

Not connected NC 29 O O 30 NC Not connected

+5,0V DC Power VCC 31 O O 32 VCC +5,0V DC Power

+5,0V DC Power VCC 33 O O 34 VCC +5,0V DC Power

Backlight enable /BLON 35 O O 36 GND Power Ground

Power Ground GND 37 O O 38 +12V +12,0V DC Power

+12,0V DC Power +12V 39 O O 40 +12V +12,0V DC Power

Kontron Embedded Modules GmbH

Flatpanel Solutions

Marschnerstieg 7

22081 Hamburg / Germany

Fon: +49 (0)40 20 00 90-0

Fax: +49 (0)40 20 00 90-10

http://www.kontron-emea.com/flatpanel

X-BOARD-UPA

08.09.2004 8

4.3 JILI40 – Interface connector X3

All flat screen signals are LVDS compatible

Connector Double Row 2mm, 40 Contacts, Gold plated

Case/Size : Vertical, Through Hole

Matching connector: FCI 90311-040

Description Name Pin

Pin Name Description

Backlight Power SW_BACK 1 O O 2 SW_BACK Backlight Power

Backlight Dimming BRIGHT 3 O O 4 NC Not connected

Not connected NC 5 O O 6 +12V +12,0V DC Power

Not connected NC 7 O O 8 NC Not connected

+12,0V DC Power +12V 9 O O 10 NC Not connected

Not connected NC 11 O O 12 +12V +12,0V DC Power

Not connected NC 13 O O 14 NC Not connected

+12,0V DC Power +12V 15 O O 16 NC Not connected

Not connected NC 17 O O 18 +12V +12,0V DC Power

Receiver Signal FTX3+ 19 O O 20 FTX3- Receiver Signal

Power Ground GND 21 O O 21 GND Power Ground

I2C Clock JILI_CLK 23 O O 24 JILI_DAT I2C Data

Power Ground GND 25 O O 26 FTXC+ Receiver Signal

Receiver Signal FTXC- 27 O O 28 GND Power Ground

Receiver Signal FTX2+ 29 O O 30 FTX2- Receiver Signal

Power Ground GND 31 O O 32 FTX1+ Receiver Signal

Receiver Signal FTX1- 33 O O 34 GND Power Ground

Receiver Signal FTX0+ 35 O O 36 FTX0- Receiver Signal

Power Ground GND 37 O O 38 GND Power Ground

Panel Power SW_VDD 39 O O 40 SW_VDD Panel Power

4.4 DIG30 - Interface connector X6

All flat screen signals are LVTTL compatible (3.3V)

Connector Single Row, 3 Contacts, Case/Size : Right Angle, 1,25mm Pitch

Matching Connector: Hirose DF14-30S-1.25C

Description Name Pin

Pin Name Description

Panel Power SW_VDD 1 O O 2 SW_VDD Panel Power

Power Ground GND 3 O O 4 SCLK Data Clock

Power Ground GND 5 O O 6 Vsync First Line Marker

Latch pulse Hsync 7 O O 8 DE Data Enable

Power Ground GND 9 O O 10 R0 Panel Data R0

Panel Data R1 R1 11 O O 12 R2 Panel Data R2

Panel Data R3 R3 13 O O 14 R4 Panel Data R4

Panel Data R5 R5 15 O O 16 GND Power Ground

Panel Data G0 G0 17 O O 18 G1 Panel Data G1

Panel Data G2 G2 19 O O 20 G3 Panel Data G3

Panel Data G4 G4 21 O O 21 G5 Panel Data G5

Power Ground GND 23 O O 24 B0 Panel Data B0

Panel Data B1 B1 25 O O 26 B2 Panel Data B2

Panel Data B3 B3 27 O O 28 B4 Panel Data B4

Panel Data B5 B5 29 O O 30 GND Power Ground

Kontron Embedded Modules GmbH

Flatpanel Solutions

Marschnerstieg 7

22081 Hamburg / Germany

Fon: +49 (0)40 20 00 90-0

Fax: +49 (0)40 20 00 90-10

http://www.kontron-emea.com/flatpanel

X-BOARD-UPA

08.09.2004 9

4.5 FLEX32 - Interface connector X7

All flat screen signals are LVTTL compatible (3.3V)

Flatfoil 32 Contacts, Right Angle, Bottom Contact

Case/Size: 0,5mm Pitch, Series: 6210 / ZIF

Description Name Pin

Pin Name Description

Power Ground GND 1 O O 2 SCLK Data Clock

Latch pulse Hsync 3 O O 4 Vsync First Line Marker

Power Ground GND 5 O O 6 R0 Panel Data R0

Panel Data R1 R1 7 O O 8 R2 Panel Data R2

Panel Data R3 R3 9 O O 10 R4 Panel Data R4

Panel Data R5 R5 11 O O 12 GND Power Ground

Panel Data G0 G0 13 O O 14 G1 Panel Data G1

Panel Data G2 G2 15 O O 16 G3 Panel Data G3

Panel Data G4 G4 17 O O 18 G5 Panel Data G5

Power Ground GND 19 O O 20 B0 Panel Data B0

Panel Data B1 B1 21 O O 21 B2 Panel Data B2

Panel Data B3 B3 23 O O 24 B4 Panel Data B4

Panel Data B5 B5 25 O O 26 GND Power Ground

Data Enable DE 27 O O 28 SW_VDD Panel Power

Panel Power SW_VDD 29 O O 30 R/L Right/Left rotate

Up/Down rotate U/D 31 O O 32 Q/V QVGA/VGA Mode

4.6 Extern Power connector (option) X8

4 Contact Connector, Single Row, Right Angle, Polarization, through hole

Matching Connector: AMP 171822-4

Description Name Pin

Function

+5,0V DC Power VCC 1 O

Power Ground GND 2 O

Power Ground GND 3 O

+12,0V DC Power +12V 4 O

4.7 Backlight connector X9

Apply operating voltage for backlight inverter using

connector X9

Board to Cable Connector, single row, 7 Contacts, Right Angle

Case/Size: 1,25mm Pitch, Matching connector: Molex 51021-0700

Description Name Pin

Function

Not connected NC 1 O Not connected

Backlight Dimming BRIGHT 2 O Analog signal 0V to 4,8V

Power Ground GND 3 O Power Ground

Backlight Power SW_BACK 4 O 5 / 12 V DC (switched) see 3.4

Backlight Power SW_BACK 5 O 5 / 12 V DC (switched) see 3.4

Power Ground GND 6 O Power Grund

Backlight enable ENABKL 7 O Backlight control signal (TTL)

Kontron Embedded Modules GmbH

Flatpanel Solutions

Marschnerstieg 7

22081 Hamburg / Germany

Fon: +49 (0)40 20 00 90-0

Fax: +49 (0)40 20 00 90-10

http://www.kontron-emea.com/flatpanel

X-BOARD-UPA

5.0 Layout

08.09.2004 10

Tabla de contenidos

Otros manuales de Hardware de computadora de Kontron

Kontron

Kontron CP-RIO6-923 Manual de usuario

Kontron

Kontron coolMonster/PM Manual de usuario

Kontron

Kontron MSP8020 Series Manual de usuario

Kontron

Kontron MITX-CFL0 Series Manual de usuario

Kontron

Kontron KBox F-420-WLU Manual de usuario

Kontron

Kontron COMh-caRP Manual de usuario

Kontron

Kontron COMh-sdID Manual de usuario

Kontron

Kontron KBox C-102 Series Manual de usuario

Kontron

Kontron AM4500 Manual de usuario

Kontron

Kontron ETXexpress-WPM Manual de usuario

Kontron

Kontron MPC-pONE Manual de usuario

Kontron

Kontron nanoETXexpress-SP Manual de usuario

Kontron

Kontron microETXexpress-DC Manual de usuario

Kontron

Kontron CI5TTV Series Manual de usuario

Kontron

Kontron CP6500-V Manual de usuario

Kontron

Kontron KTGM45/mITX Manual de usuario

Kontron

Kontron SMARC-sAMX8X Manual de usuario

Kontron

Kontron COM-HPC Manual de usuario

Kontron

Kontron Kiss 2U Manual de usuario

Kontron

Kontron Mungo540 Manual de usuario

Kontron

Kontron USB-16REL Manual de usuario

Kontron

Kontron MUNGO560 Manual de usuario

Kontron

Kontron CP6003-SA Manual de usuario

Kontron

Kontron ePanel-C3 Manual de usuario

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario

Advantech

Advantech ASMB-935 Series Manual de usuario

Jupiter

Jupiter RAM PACK Manual de usuario