Konica Minolta inpro Manual de usuario
© 2014 Inepro B.V. All rights reserved
Technical Manual | Inepro IP Reader (Konica Minolta)
Inepro IP Reader
(Konica Minolta)
Product Version: Rev. 3
Version of this manual: 2.0.1
Inepro IP Reader (Konica Minolta)
Congratulations on your selection of Inepro card readers. We are certain you will be
pleased with your purchase of one of the flexibele solutions of the market.
We want to help you get the best result from your Inepro Back Office Suite. This manual
contains information on how to do that; please read it carefully. Due to continuous
product improvements this manual is subject to changes without notice.
We strongly recommend you read the license agreement to fully understand its coverage
and your responsibilities of ownership.
Your Inepro dealer is dedicated to your satisfaction and will be pleased to answer your
questions and your concerns.
Best wishes,
Inepro BV.
The most versatile card reader solution
All rights reserved. No parts of this work may be reproduced in any form or by any means -
graphic, electronic, or mechanical, including photocopying, recording, taping, or information
storage and retrieval systems - without the written permission of the publisher.
Products that are referred to in this document may be either trademarks and/or registered
trademarks of the respective owners. The publisher and the author make no claim to these
trademarks.
While every precaution has been taken in the preparation of this document, the publisher and
the author assume no responsibility for errors or omissions, or for damages resulting from the
use of information contained in this document or from the use of programs and source code that
may accompany it. In no event shall the publisher and the author be liable for any loss of profit
or any other commercial damage caused or alleged to have been caused directly or indirectly by
this document.
Version 2.0.1 created: November 2014 in Nieuw-Vennep.
Publisher
Managing Editor
Technical Editors
Cover Design
Inepro B.V.
K. de Graaf
P. Blom
K. de Graaf
Production
Inepro B.V.
Team Coordinator
R. Groen
H. Wagenaar
R. de Koker
Inepro IP Reader (Konica Minolta)
ATTENTION!!
Read this manual carefully before installing the IP Reader!
Mains connection
Guarentee
Security
Before connecting the appliance to the mains, check that the mains supply voltage corresponds
to the voltage printed on the type plate of the adapter. If the mains voltage is different, consult
your supplier.
No guarantee can be given if safety regulations are not followed.
Always disconnect the power supply before handling anything inside the device.
This device is in conformity with the EMC directive and low-voltage directive.
CE Conformité Europeène (Conform European Norm)
End of life directives
Inepro is paying a lot of attention to environmentally-friendly production. Your new device contain
materials which can be recycled and reused. At the end of its life specialised companies can
dismantle the discarded device to recycle the reusable materials and to minimise the amount of
materials to be disposed of. Please observe the local regulations regarding the disposal of
packaging materials, exhausted batteries and old equipment.
This device may only be used indoors.
Indoor User Only
Directives
Version 2.0.1 - I
I
Introduction
Part
Introduction
Version 2.0.1 - 2
Introduction
In this manual you find the instructions to install and configure your
IP-reader. This manual is meant for all the Konica Minolta
IP-readers.
This manual, the IP reader hardware and software are subject to
change, make sure you have the latest version of this manual,
because the older versions may have become obsolete.
Konica Minolta IP-readers:
·361100 Inepro IP Card Reader Mifare KoMi
·361101 Inepro IP Card Reader Mifare Desfire KoMi
·361102 Inepro IP Card Reader Legic Prime KoMi
·361103 Inepro IP Card Reader Legic Advant KoMi
·361104 Inepro IP Card Reader HiD iClass KoMi
·361105 Inepro IP Card Reader HiD Prox KoMi
·361106 Inepro IP Card Reader HiD Indala KoMi
·361107 Inepro IP Card Reader Multitag KoMi
Function
The purpose of the IP reader is to read the unique ID contained in
the card that is presented to the reader and transfer this ID to a
server. In most cases this data will be the card serial number. To
facilitate this a variety of card reader software module have been
developed. Our configuration tool will enable you to change the
setting on the IP reader board.
3 - Inepro IP Reader (Konica Minolta)
Topics
The following topics will be addressed:
1. The components in the IP-reader set
2. The operating procedures
3. Network Connections
4. Software configuration settings
5. Connecting to the Business Server
II
Components
Part
5 - Inepro IP Reader (Konica Minolta)
Components
The IP Reader consists of the following components:
·Grey Card Reader Housing
-Grey Antenna Box
-Antenna Box Cap 1 / Grey
-Antenna Box Cap 2 / Grey
·Controller Box
·Wire Duct - Grey
·Network Cables
-Network Cable UTP C5E Patch Black (0,5mtr.)
-Network Cable UTP C5E Patch Black (2,0mtr.)
Tabla de contenidos
