Kongskilde KONNECT 1000 Manual de usuario
KONGSKILDE KONNECT 1000
Instruction manual
EN
Edition: 251018
2
KONNECT 1000 EN 251017
CONTENTS
GENERALLY.......................................................................................................................3
1.Foreword............................................................................................................. 3
2.Technical data.....................................................................................................4
3.Equipment........................................................................................................... 4
4.Safety Precautions.............................................................................................. 4
FEATURES AND USE........................................................................................................5
5.Keyboard ............................................................................................................5
6. Monitor setup ..................................................................................................... 6
6.1 Language selection................................................................................6
6.2 Work screen............................................................................................6
6.3 Screen brightness and contrast..............................................................7
6.4 Alarm settings.........................................................................................7
6.5 Alarms.....................................................................................................8
6.6 Selection of the type of machine.............................................................8
6.7 Selection of the number of pulses...........................................................9
6.8 Alarm time...............................................................................................9
6.9 Working width........................................................................................10
6.10 Hectare counter...................................................................................10
6.11 Half working width setup - option.........................................................10
CALIBRATION....................................................................................................................11
7.Generally.............................................................................................................11
7.1 Calibration sequence..............................................................................11
TRAMLINING......................................................................................................................13
8. Tramlining choice of method..............................................................................15
8.1 Symmetrical tramlines............................................................................15
8.2 Asymmetrical tramlines..........................................................................15
8.3 Rules for selection of tramline path........................................................16
8.4 Manually stop the tramlining system......................................................17
9.Tables of symmetrical tramlines....................................................................18-19
10.Table of asymmetrical tramlines........................................................................20
NOTES...........................................................................................................................21-22
3
GENERALLY
1. FOREWORD
KONGSKILDE this I would like to congratulate the purchase of new electronic Tramline
monitor KONNECT 1000 for monitoring electronic functions of the drill, including the
establishment of tramlines.
In order to use the KONNECT 1000 correctly and safely, we recommend that you familiarize
yourself with it by studying this instruction manual.
The correct use of the KONNECT 1000, along with careful maintenance, lubrication and
storage, will help to keep it in good working order.
FEATURES
While working KONNECT 1000 provides data, as follows:
- The speed set tractor-seeder,
- Partial or total value of the area sown,
- Controls the rotation of the sowing shaft,
- Informs about the low level of seed in the hopper,
- Provides current information on the status of tramlines.
TRAMLINES
Tramline system, we want to get is determined by the working width of the drill and held a
working width of the sprayer / spreader.
These data, as input, we give using the keyboard:
- KONNECT 1000 device automatically calculates and gives the possible combinations of
paths to follow,
- Counting the passing takes place by means of sensors counting raising and lowering the
markers on the turning circle,
- Paths are formed by stopping the operation of selected sowing wheels. Wheels are
retained on a clutch controlled from the device,
- During the passage without making tramlines, all the sowing wheels work.
KONNECT 1000 device is powered using the included cable to the electrical system (12 V)
of the tractor. The terminal can be located in the tractor cab at any place. On the back wall
is built magnet for easy mounting.
4
KONNECT 1000 EN 270217
GENERALLY
2. TECHNICAL DATA
Power supply +10.... +15V
Current consumption 120mA without active tramline outputs
Output current max. 5A for tramline outputs
Working temperature range -5....+60º C
Storage temperature -25....+60º C
Protection grade IP 65
Fuse 10A automotive fuse inside the power plug
LC-Display 2,5" monochrome 128 x 64 Pixel
The device is EMC tested according:
Electromagnetic emission EN 55022
Electromagnetic immunity DIN EN 14982
3. EQUIPMENT
The KONNECT 1000 is tted with the following equipment:
-Operator terminal KONNECT 1000 and a 6 m cable
- Main harness ended plugs, tted in the machine frame
-Two sets to tracks with couplings and connectors
-One set of marker sensors with 1,5 m wires
-Set of sensor for hopper level control(optional)
-Half working width clutch for seeding shaft controlled by a LINAK actuator (optional)
-Set of tramlining valves NS 4100, NS 5100, NS 1500\1900, Vibro Seeder
4. SAFETY PRECAUTIONS
Clutch housings and sowing wheels must not be cleaned with liquids containing chlorine and
hydrocarbons, e.g. petrol. Do not power wash down the clutches with water.
KONNECT 1000 should be kept in a dry place. Therefore do not leave it in the tractor cab
for a long period after the sowing season has nished.
When unused for a long period it is important to check that the tube carrying the sowing
wheels has not locked on the sowing shaft. This done by turning forward with your hand the
tube with the sowing wheels (the same direction as the sowing shaft turns when the machine
is working).
This can be done without electric current on the clutch. Never use pipe grips or other tools
on the tube, as it might become deformed and therefore lock on to the sowing shaft.
BEFORE SOWING
When using the electronic tramlining device the markers must be adjusted accurately according
to the working width in order to avoid overlaps and unsown areas with a sprayer or fertilizer
distributor.
5
FEATURES AND USE
5.KEYBOARD
The handling of KONNECT 1000 is possible via keypad with 9 keys.
With the “ON/OFF” key the operator terminal is powered on and by pressing the key with
1s duration it is switches off. If no key is pressed one hour and in the same time no velocity
is measured, the device switches off automatically.
In the upper line are placed the keys for parameter adjustment. With the
“MENU OK” (Function key) several setup menus are selected one by one.
Adjusted values must be stored by pressing the “MENU OK”for 5 sec until the beep. In
some menus the 3 upper keys also are used as soft-keys, their actual function is shown at
the lower border of the display.
The left button in the middle row “km / h” show us the current forward speed.
In addition, by using this button to set the number of pulses that will calculate the system
for calculating the sown area.
Middle button “ha” gives us the current value of area sown eld or value overall.
The “Select tramlining” supports tramlining. When pressed, the tramline function is
entered. Use the “up-down” to select sequentially tramlining systems. You should choose
the right system and then conrm it by holding down the “MENU OK”for 5 seconds. Beep
to conrm the selection system.
The lower left “half width” is active after selecting half sowing seed (optional).
The middle button “WORK” we use at the start of work on the eld.
“MENU OK” Select
setup menu/store
values
“km-h” key speed
100 m setting
“half width”
Key optional
“Work Key” work
“up-down” Increase
and decrease Input
value
“ha- key” segment and
total hectar counter
“Select tramlining”
set tramline sequence
and start eld
“ON/OFF” Operator
terminal
6
KONNECT 1000 EN 251017
FEATURES AND USE
6.MONITOR SETUP
Setting the individual parameters of the work is done by pressing the function key “MENU
OK”. In addition, the “MENU OK” is for approval settings. After conrming the selection by
holding down the button for 5 seconds - the symbol of the oppy disc, the lower left corner
of the screen. A beep conrms the setting.
6.1 LANGUAGE SELECTION
It is possible to choose a number of different languages.
English, Polish, German, French, Danish, Dutch, Hungarian, Italian, Swedish, Spanish.
Language
English
5s
Use the “up-down” select the language.
When the function key “MENU OK” is pressed and held for 5 seconds, the system ap-
proves and memorizes the selected language.
6.2 WORK SCREEN
After rst pressing the “ON/OFF”get the screen working. It is the main screen, always
used while working in the eld. First turned on the monitor does not contain information on
the screen with required parameters for work. Look below:
00
00 1
km
h
ha
SY 3
Typical appearance of the screen working, as observed during eld work. Look below:
7,0
2
48,1
km
h
ha
SY 4
The top row from left: symbol hopper shows us the status of full box of seed (only two states:
empty, full), the current speed of the machine and the selected tramlining system.
Bottom row from left: sowing shaft rotation, the area sown so far.
7
FEATURES AND USE
6.3 SCREEN BRIGHTNESS AND CONTRAST
The third press of the “MENU OK” selects the display brightness setting.
Display
OK
Display
OK
Use the arrow keys “up-down” select, by means of a bar chart, the corresponding value of the
brightness of the display. Pressing the “MENU OK”approve the selected level.
6.4 ALARM SETTINGS
The seed level in the hopper and work couplings pathnames can be monitored by means of audible
alarms. Activation or deactivation of alarms make the level below the monitor.
Set Alarm
5s
Use the “up-down” select the type of alarm - horizontal bar under the selected icon, and further put a
check mark - “bird“-up button. Conrm the settings by pressing the function key “MENU OK” - hold
it for 5 seconds. Beep saves the settings.
Carrying out the sensor test is to check the condition of electrical connections, the state plugs
connecting cables, the technical condition of the sensors.
Sensor
Te s t LR
The top row of icons is a state of coupling the left and right control tramlines. The bottom row of icons
indicates the level of seed in the tank, turns the sowing shaft and position markers. Covering the sen-
sor in the transmission, e.g. Hand, appears to us a symbol of a full box. By turning the crank sowing
shaft - appears to us arrow icon on the wheel, leaving the marks we see the variable position of the
marker icon.
8
KONNECT 1000 EN 251017
FEATURES AND USE
The following screen display shows the status of the sensors:
Actuator test
on
LR
Use the “up” select the type of sensor - a horizontal line under the icons, which is checked.
Highlighted in black icon indicates that the sensor is active.
6.5 ALARMS
Watching of hopper and tramline clutches work at a speed of more than 1 km/h. In case of
a fault an alarm screen with ashing icon is displayed and the outputs 5 beeps. The alarm
can be acknowledged by the work-key. This action returns to the work screen.The tramline
clutches are checked, that they have stopped, when tramlines are active. When tramlines
are not active the sensors in the clutches have to output impulses. At clutches alarm the
side is displayed with the characters L (left) or R (right).
6.6 SELECTION OF THE TYPE OF MACHINE
This is very important because the type of machine contains the type of the drive wheel
and the working width.
Machines type:
ECO 2,5m 7.00x12
ECO 3,0m 7.00x12
PROFI 3,0m 10/80x12
5s
Use the “up-down” select the type of machine.
When you press the function key “MENU OK” for 5 seconds, the system approves and
memorizes the type of drill.
6.7 SELECTION OF THE NUMBER OF PULSES
Area meter accuracy of the calculation depends on the number of impulses in the system
collects during operation of the drill in the eld. The following method is to calculate the
number of pulses according to the following formula:
pulses = 3183
rubber wheel diameter (in cm)
9
FEATURES AND USE
Choose the speed display of the machine by the “MENU OK”
Imp.
100 m
+
_
100
5s
Enter the number of impulses from the table below.
Saving in memory the number of pulses is necessary for the correct indication of sown
area. Depending on the drill (diameter of the wheel), medium slides on the soil - the
number of counted pulses is different. When you press the function key “MENU OK”for 5
seconds, the system approved by us in memory the value of the number of pulses.
Type drill
Eco Line Wheel 7.00x12
Wheel 6.00x16
Wheel 10.0/80x12
Land wheel
Land wheel
Land wheel
48
52
54
50
50
50
Profi Line
Profi Line
Master Line
NS 4100
NS 5100
Type wheel drive Wheel impulses per 100 m
6.8 ALARM TIME
Determining the time after which the alarm is activated is very important. This time can be
adjusted from 1 second to 20 seconds - the key “up-down”
Alarm time
5s +_
6s
The shorter the response time of the system, the faster we can detect any problems during
operation, e.g. locked sowing shaft, low seed in the hopper and so on.
When you press the function key “MENU OK” for 5 seconds, the system approved by us in
memory the type of drill.
10
KONNECT 1000 EN 251017
FEATURES AND USE
6.9 WORKING WIDTH
This option allows changing the working width of the drill.
There is a choice of width in the range from 2m to 12m with intervals of 0,1 m.
m
+_
9,7
5s
Use the “up-down” select the working width.
When pressing the function key “MENU OK” for 5 seconds, the system approves and
memorizes the selected working width.
6.10 HECTARE COUNTER
The rst press: “ha” gives us a partial result of the count sown area, but repeated pressing
gives the total area sown so far surfaces. Then, before the digit number of hectares sign
appears: “
Σ
”Shown the value of sown area can be reset by long pressing on the button
”ha” 5 seconds.
ha
48,1 ha
Σ50,1
6.11 HALF WORKING WIDTH SETUP - OPTION
In some tramline sequence systems, it is necessary to begin with a half working width.
Then the icon “half width”is displayed automatically. In contrast, we can always use this
function at any time by pressing the button in the lower left corner of the keyboard icon
“half width”
The drill should be equipped with LINAK actuator system.
Then sowing shaft is disconnected in the middle of its length by means of the clutch cen-
ter. Thereby half the sowing wheels on the left hand side of the drill from the rear of the
machine are not running.
Tabla de contenidos
