Kogan KASNSRWFTHA Manual de usuario
KOGAN SMARTERHOME™ SMART
TEMPERATURE & HUMIDITY SENSOR
(WI-FI)
KASNSRWFTHA
Read all instructions and safety notes before first use. Retain this guide for future
reference.
• Do not use in an environment with humidity over 90%.
• Do not use in an environment with temperature lower than -10°C.
• To conserve battery this product has been set with a 30 second upload delay.
Power
SAFETY & WARNINGS
OVERVIEW
Temperature
Humidity
WI-FI Signal
Install App
Download the “Kogan SmarterHome” app from the Play Store (Android) or App Store (iOS).
Register
If you do not have a Kogan SmarterHome™ account, register or sign in with a verification
code sent by SMS.
To R e g i s t e r
1. Ta p t o e n t e r r e g i s t r a t i o n p a g e .
2. The system automatically recognises your country/area. You can also select your
country code manually. Enter your email address and tap ‘Next.’
3. Alternatively, you can select ‘Register by mobile number' and enter the verification
code sent to you by SMS.
4. Create a profile on the next page to define your location and room.
CONNECT TO SMARTERHOME™ APP
Set device in pairing mode
Open the battery compartment and install two (2) AAA batteries and close. Alternatively,
this product can be powered using a USB cable.
When the device is first turned on, it may automatically enter pairing mode (device will
beep).
If not automatically in pairing mode, you can manually set the device in pairing mode by
using a pin to press the reset button for 5 seconds until the Wi-Fi icon begins flashing or
the device ‘Beeps’.
Reset
Add device through network
5. Once registered, tap “+” in the upper right corner of the app’s home page to add a
new device through the network.
6. Select the product type from the list of options in the app (Sensor > Thermostat).
7. Ensure that the device is in pairing mode, with the Wi-Fi icon flashing rapidly and
tap “Confirm indicator rapidly blink”.
8. Upon successfully confirming pairing mode, enter your Wi-Fi details. It is important
that your SmarterHome™ device and the app are connected to the same Wi-Fi
network during setup.
9. The device will commence the pairing process and connect to the app. Ensure your
Wi-Fi router, mobile phone, and the SmarterHome™ device are kept close until
connection is complete.
10. After successfully being added, you will have the option to rename the device and
assign it to a location. It will now be listed on the app’s home page. Tap the device
listing to enter its control page.
Notes:
• The device and the app have to use the same Wi-Fi network.
• The device is only compatible with 2.4Ghz networks.
Add device through Bluetooth
5. Ensure that the device is in pairing mode (Wi-Fi icon flashing or the device ‘Beeps’).
6. Connect your smart phone to your 2.4GHz Wi-Fi network.
7. Ensure that Bluetooth is enabled on your smart phone.
8. Open the “Kogan SmarterHome” app.
9. Tap “+” in the upper right corner of the app’s home page to add a new device
through the network.
10. The app will automatically detect the device, tap “Go to add”.
11. If the device doesn't appear automatically, please select it in the device list and
follow the prompt to detect/connect your device.
12. The device will commence the pairing process and connect to the gateway and
app. Ensure your Wi-Fi router, mobile phone, and the SmarterHome™ device are
kept close until connection is complete.
13. After successfully being added, you will have the option to rename the device and
assign it to a location. It will now be listed on the app’s home page. Tap the device
listing to enter its control page.
If the above two methods aren’t successful, use ‘AP Mode’ to add device
5. Remove and re-insert the batteries then use a pin to press the reset button for 5
seconds until the Wi-Fi icon begins flashing rapidly. Press the reset button for
another 5 seconds until the Wi-Fi icon begins flashing slowly.
6. Once registered, tap “+” in the upper right corner of the app’s home page to add a
new device through the network.
7. Select the product type from the list of options in the app (Sensor > Thermostat),
and then select “Other Mode” from the top-right corner when asked to reset the
device.
8. Select “AP Mode” for the set-up type.
9. Ensure that the device is in pairing mode, with the Wi-Fi icon flashing slowly and
tap “Confirm indicator slowly blink”.
10. Enter your Wi-Fi details. It is important that your SmarterHome™ device and the
app are connected to the same Wi-Fi network during setup.
Tabla de contenidos
Otros manuales de Accesorios de Kogan
Kogan
Kogan KAPB10K225A Manual de usuario
Kogan
Kogan OVELA OVCEBL12BA Manual de usuario
Kogan
Kogan SMARTERHOME KARMDF1800A Manual de usuario
Kogan
Kogan SMARTERHOME SMART POWER BOARD Manual de usuario
Kogan
Kogan KAPWB26UNIA Manual de usuario
Kogan
Kogan KATRCHNCMPA Manual de usuario
Kogan
Kogan KAPB10KALBA Manual de usuario
Kogan
Kogan KAPB26800HC Manual de usuario
Kogan
Kogan KACRDWFLBKA Manual de usuario
Kogan
Kogan SMARTERHOME SECURITY CAMERA DOORBELL 3 PRO Manual de usuario
Kogan
Kogan KAPWB45SLSA Manual de usuario
Kogan
Kogan KAPWBLG5RDA Manual de usuario
Kogan
Kogan KAWLSDBELL Manual de usuario
Kogan
Kogan KAPDPBQC20A Manual de usuario
Kogan
Kogan KAM43BEVFGA Manual de usuario
Kogan
Kogan KASHSDRBELA Manual de usuario
Kogan
Kogan KAWLSDBELLC Manual de usuario
Kogan
Kogan Cordless Portable Travel Water Flosser Manual de usuario
Kogan
Kogan SMARTERHOME SMART DOORBELL 2 PRO Manual de usuario
Kogan
Kogan KAELBLFFSBA Manual de usuario
