Kodak RFS 3570 Manual de usuario
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User’s Manual
KODAK Professional
RFS 3570 Film Scanner
© Eastman Kodak Company, 1997.
This manual and the accompanying software are protected by United States and international
copyright laws. You may make one backup copy of the enclosed software and one copy of this
manual. Do not make additional copies of the software or copies of the manual or electronically
transmit them in any form whatsoever, in whole or in part, without the prior written permission
of Eastman Kodak Company.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ii
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iii
Important Safeguards and
Precautions
WARNING: To prevent fire or shock hazard, do not expose unit to rain
or moisture.
CAUTION
RISK OF ELECTRIC
SHOCK DO NOT OPEN
CAUTION: TO REDUCE THE RISK
OF ELECTRIC SHOCK, DO NOT
REMOVE COVER. NO USER-
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
Read Instructions — Read all the safety and operating instructions
before operating the unit.
Retain Instructions and Packing Materials — Retain the safety and
operating instructions for future reference. Retain the packing case for
use if the equipment must be shipped.
Heed Warnings — Heed all warnings on the equipment and in the
operating instructions.
Follow Instructions — Follow all operating and use instructions.
Controls — Adjust only those controls that are covered by the operat-
ing instructions.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iv
Cleaning — Unplug the unit before cleaning. Clean only the outside
cabinet with a damp cloth. Do not use liquid cleaners or aerosol
cleaners.
Attachments — Do not use attachments that are not recommended.
The use of such attachments may cause hazards and serious damage
to the equipment.
WARNING: Water and Moisture — Do not use the equipment near
water — for example, near a sink, or in a wet room or basement, etc.
Do not expose the unit to rain or moisture and do not immerse the
equipment in water or other liquids; contact Kodak for servicing if this
occurs.
Dust — Excessive dust levels may damage internal parts. Be certain to
cover the scanner with the supplied dust cover whenever the scanner
is off. Because dust can build up in the scanner and affect image
quality, we recommend that you follow the procedure at the begin-
ning of each work session that is described at the end of “Appendix
C — Trouleshooting.” Doing so will help to ensure that you remove
dust buildup before scanning.
Power Sources — You should operate the unit only from the type of
power source indicated on the back of the unit. If you are not sure of
the type of power supply that will be used, consult a dealer or local
power company.
Replaceable Fuse — There is one replaceable fuse in the unit. Be sure
that the fuse meets the power requirements listed on the fuse-rating
label on the unit.
Grounding — The unit is equipped with a three-wire grounding-type
plug with a third (grounding) pin. The three-wire plug will fit into a
grounding-type power outlet. This is a safety feature. If you are unable
to insert the plug into an outlet, contact an electrician to replace the
obsolete outlet. Do not defeat the safety purpose of the grounding-type
plug.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
v
Power-Cord Protection — Route power-supply cords so that they are
not likely to be walked on or pinched by items placed on or against
them; pay particular attention to cords at plugs, receptacles, and the
point where they leave the unit.
Operating Range — If the Scanner has been stored or transported
outside its operating ambient temperature range (refer to
“Appendix J — Specifications”), allow it to return to within its operat-
ing range before turning it on.
Lightning — For added protection of the equipment during a lightning
storm, or any time when you will leave the equipment unattended
and unused for long periods of time, unplug the unit from the power
outlet. This will protect the equipment from damage caused by
lightning or power-line surges.
Overloading — Do not overload power outlets and extension cords;
this can result in a risk of fire or electric shock.
Object or Liquid Entry — Never push foreign objects of any kind into
the equipment openings. Never spill liquid of any kind on the equip-
ment; contact Kodak for servicing if this occurs.
Servicing — Do not attempt to service the unit yourself, except to
change the fuse (see instructions in “Appendix E — Replacing the
Fuse”). Opening or removing covers may expose you to dangerous
voltage or other hazards.
Damage Requiring Service — Unplug the unit from the wall outlet
and refer all servicing to the manufacturer under the following condi-
tions. (Refer to “Appendix B — Warranty” for additional information.)
– When the power-supply cord or plug is damaged (send cord
only). Power cords are available as a spare part; refer to
“Appendix I — Optional Equipment & Spare Parts List.”
– If liquid has been spilled or if objects have fallen into the equip-
ment.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
vi
– If the equipment has been exposed to rain or water.
– If the unit does not operate normally according to the operating
instructions.
– If the unit has been dropped or the housing has been damaged.
– When the equipment exhibits a distinct change in performance.
Accessories — Do not place the unit on an unstable cart, stand,
bracket, or table. It can fall, causing serious injury to persons and
serious damage to the unit. Use only with a stable cart, stand, bracket,
or table.
Handling — Handle the equipment with care; do not drop the equip-
ment.
CAUTION: To prevent fire or shock hazard, use only the recom-
mended accessories or attachments.
Electromagnetic Emissions
This equipment has been tested and found to comply with the limits for a
Class A digital device pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interfer-
ence when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference, in
which case the user will be required to correct the interference at his or
her own expense.
This equipment conforms with the requirements of European Standard
EN55022 with respect to radio interference for a Class A device.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
vii
Le présent appareil numérique n’émet pas de bruits radioélectriques
dépassant les limites applicables aux appareils numériques de la classe A
prescrites dans le règlement sur le broullage radioélectrique édicté par le
Ministère des Communications du Canada.
This digital apparatus does not exceed the Class A limits for radio noise
emissions from digital apparatus set out in the radio interference regula-
tions of the Canadian Department of Communications.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
viii
Technical Assistance
Refer to the following sources for assistance if you have questions as you
work with the Scanner.
If you encounter difficulties with hardware, with scanned images or
with product performance, refer to “Appendix C — Troubleshooting.”
If you notice circular shaped objects in scanned images — like water
spots or bubbles — be certain that you follow the procedure at the
beginning of each work session that is described at the end of “Ap-
pendix C — Troubleshooting.” Doing so will help to ensure that you
remove dust buildup before scanning.
If a message appears on the computer screen that you do not under-
stand, refer to “Appendix D — Messages from KODAK Drivers.”
If you need other assistance from this manual, refer to the “Contents”
and the “Index.”
If you are unable to find answers from this manual, contact your
dealer.
If you are a customer in the United States and you are unable to find
answers to your questions using this manual or from you dealer, call
Kodak at 1-800-CD-KODAK.
If you are a customer in Canada and you are unable to find answers to
your questions using this manual or from your dealer, call Kodak at 1-
800-465-6325.
If you are a customer outside the United States or Canada and you are
unable to find answers to your questions using this manual, contact
your local Kodak representative for technical assistance.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ix
Contents
1Introduction 1-1
2Before You Begin — Macintosh Computer 2-1
Required Hardware 2-2
Computer 2-2
Monitor 2-2
Display Card 2-2
Required Software 2-3
Optional Printers 2-4
3Installation
(Hardware and Software) — Macintosh Computer 3-1
Installing the Scanner Hardware 3-2
Connecting the Scanner to a Power Source 3-2
Connecting the Scanner to Your Computer 3-3
If No External SCSI Devices Are Connected 3-5
If External SCSI Devices Are Connected 3-9
Setting the Scanner SCSI Identification Number 3-19
Installing the KODAK Driver for Adobe Photoshop Software (Macintosh) 3-21
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
x
4Loading the Film and Slide Holders — Macintosh Computer 4-1
Loading 35 mm Film and Slides 4-2
Loading 35 mm Film into the 35 mm Film Holder 4-2
Loading 35 mm Slides into the Slide Holder 4-3
Loading 35 mm Film and Slide Holders into the Scanner 4-4
Loading Film Sizes Other Than 35 mm 4-8
Loading Film into the Film Holder 4-8
Loading Film Holders (Other Than 35 mm Sizes) into the Scanner 4-10
5Using the KODAK Driver for Adobe Photoshop Software —
Macintosh Computer 5-1
Displaying the KODAK Driver Window 5-3
Producing Scanned Images 5-5
Loading the Film Holder 5-5
Operating the KODAK Driver 5-6
Set the Film Type 5-6
Set the Film Size 5-6
PreScan the Image (and Calibrate the Scanner) 5-6
Change the Magnification Adjustment 5-12
PreScan the Image Again 5-14
Select the Image 5-15
Set Auto Balance 5-16
Rotate the Image 5-16
Sharpen the Image 5-16
Set the Image to Black and White 5-17
Focus the Image 5-17
Change Color Levels 5-18
Change Brightness 5-19
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Escáner de Kodak
Kodak
Kodak I640 - Document Scanner Manual de usuario
Kodak
Kodak i55 Manual de usuario
Kodak
Kodak Scanmate i1120 Manual de usuario
Kodak
Kodak Kodak i1840 Manual de usuario
Kodak
Kodak i5250 Manual de usuario
Kodak
Kodak i1400 Series Manual de usuario
Kodak
Kodak Ngenuity 9090DB Manual de usuario
Kodak
Kodak i200 Series Manual de usuario
Kodak
Kodak i4200 Manual de usuario
Kodak
Kodak Scan Station 500 Manual de usuario
Kodak
Kodak i1800 Series Manual de usuario
Kodak
Kodak I780 - Document Scanner Manual de usuario
Kodak
Kodak i1400 Series Manual de usuario
Kodak
Kodak 1500 Manual de usuario
Kodak
Kodak 3520D - Digital Science Manual
Kodak
Kodak i5200 Manual de usuario
Kodak
Kodak P811 Manual de usuario
Kodak
Kodak i1220 Plus Manual
Kodak
Kodak PROFESSIONAL RFS 3600 Manual de usuario
Kodak
Kodak Ngenuity 9090DB Manual de usuario
