Kodak Ektalite 1000 Manual de usuario
KODAK EKTALITE Slide Projectors 43
english
Table of Contents
1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
2 Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Start-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Loading the Slide Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Operating the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Clearing a Gate Jam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
3 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Changing the Projection Lamp . . . . . . . . . . . . . . . . . . . . . . . 70
Cleaning the Condenser and Mirror . . . . . . . . . . . . . . . . . . . . 72
4 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Self-check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
5 Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
6 How to Obtain Service . . . . . . . . . . . . . . . . . . . . . . . . . 81
Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Shipping Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
7 Special Application Receptacle . . . . . . . . . . . . . . . . . . 82
Twelve-Pin Receptacle Specifications(Model 2000) . . . . . . 82
KODAK EKTALITE Slide Projectors
44
Important Safety Instructions
When operating your projector, always follow basic safety precautions:
1. Read and understand all instructions before operating your projector.
2. Before you switch on your projector, ensure that the mains voltage input is correct or is
correctly adjusted for Models 2000, 1500, and 1000! Incorrect voltage can lead to malfunction
in the projector.
3. Close supervision is necessary when any appliance is used by or near children, or others who
may not understand the need for these precautions. Do not leave the projector unattended
during use.
4. Be careful not to touch hot parts. For lamp replacement, allow the module to cool before
touching the lamp. Do not place the lamp module on heat-sensitive surfaces.
5. Do not operate your projector if the cord is damaged or if the projector has been dropped or
damaged (see “How to Obtain Service” on page 81).
6. Position the cord so that it is not tripped over, pulled, or placed in contact with hot surfaces.
7. If an extension cord is necessary, use a cord with a current rating at least equal to that of the
projector. Cords rated for less amperage than the projector may overheat.
8. Always unplug the projector from the electrical outlet before cleaning and servicing and when
it is not in use.
9. Allow the project to cool before storing.
10. Do not immerse this equipment in water or other liquids.
11. Do not disassemble this projector. Use a qualified service technician when service or repair is
required. Incorrect reassembly can cause electric shock the next time the projector is used.
12. Use only safety electrical low-voltage (SELV) devices.
13. The use of an accessory attachment not recommended by the manufacturer may increase risk
of damage.
14. Connect this projector to a grounded outlet.
15. Keep the air-flow vents unobstructed.
Electrical Approvals and CE Mark
This projector complies with International Safety requirements of IEC 335-/-2-56 and bears the
following safety marks:
•CE
• SGS Australian Standard
• TÜV
• VDE (Pending)
KODAK EKTALITE Slide Projectors 45
english
1Overview
FRONT RIGHT
1. Tray
2. Lock Ring/Cover
3. Transformer Module
4. Elevating Foot
5. Elevating Adjustment Wheel
6. Quick Release Button (Models
2000, 1500, 1000)
7. Projection Lens
8. Lens Focus and Release Knob
9. Autofocus (Models 2000, 1500)
10. Select Bar
11. Gate Index
12. Timer (Models 2000, 1500)
13. Reverse
14. Forward
15. Power (NO LIGHT/LO/HI—
Models 2000, 1500, 1000)
(NO LIGHT/ON—Model 500)
A098_0069AC
3
6
45
7
A098_0069ACA
8
9
10
11
12
13
15
14
2
1
Overview
KODAK EKTALITE Slide Projectors
46
BACK RIGHT
16. Alignment Mark
17. Index Mark
18. Lamp Module
19. Leveling Foot
20. Reading Light Cover
(Models 2000, 1500, 1000)
21. Internal/External Switch
(Model 2000)
22. Twelve-Pin (Dissolve)
Receptacle (Model 2000)
23. AC Power Main Receptacle
24. Six-Pin Remote Control
Receptacle (Models 2000, 1500,
1000)
BASE
25. Voltage Selector
(Models 2000, 1500, 1000)
26. Fixing Holes (6 mm thread)
(Models 2000, 1500, 1000)
27. Serial Number Label
28. Power Cord Retainer
A098_0070AC
23
24
A098_0070ACA
21
22
2019
18
17
16
A098_0071AC
27
28
25 26
A098_0071ACA
KODAK EKTALITE Slide Projectors 47
english
2Operation
Start-up Models 2000, 1500, and 1000 only
Caution
Before you turn on your new KODAK EKTALITE Slide Projector, it is
critical to set the voltage selector to the proper setting.
The voltage selector is located on the base of the projector. You can set
the voltage selector for the proper voltage (100, 115, 130, 220, 230, and
240 V, 50/60 Hz) by turning the selector until the arrow of your main
voltage lines up with the arrow on the projector housing.
A098_0046AC
A098_0046ACA
Voltage selector
Fuse storage door
Power BASE
Operation
KODAK EKTALITE Slide Projectors
48
A 220, 230, or 240 main requires a 2.5 A H/250 V fuse. The 100, 115
or 130 V main requires a 5 A slow blow/250 V fuse. To fit or check the
fuse, pull out the fuse holder located beneath the power main.
At manufacture, the voltage selector is set at 240 V with a 2.5A
slow blow/250 V fuse fitted in the fuse holder. A spare fuse for
replacement is provided in the first compartment of the fuse holder.
Important
Countrieswith100,115,or130Vmainwillrequireremovalofthetwo
fuses in the fuse holder. Use the 5 A slow blow/250 V fuse, provided.
Set the voltage selector for your main voltage.
After you have set the correct voltage and fitted the required fuse, you
can safely plug the projector into your power main and switch it on.
Model 500 only
Operating Voltage Range: Minimum 207V
Maximum 254 V
50/60Hz
Operation
KODAK EKTALITE Slide Projectors 49
english
All Models
Plug the 6-pin cable remote connector into the remote-control
receptacle, aligning the raised arrow with the notched side of the socket.
This receptacle also accepts plugs for accessories, such as a KODAK
EKTALITE IR Remote Control.
A098_0079AC
control
Remote
receptacle
Remote control
A098_0079ACA
Operation
KODAK EKTALITE Slide Projectors
50
Loading the
Slide Tray The KODAK EKTAPRO 80 Slide Tray (with transparent cover) and
the KODAK EKTAGRAPHIC Universal Slide Tray are designed to
hold up to 80 slides. Be sure that your slide mounts are in good
condition; frayed or bent mounts or mounts with loose tape may fail to
drop into the projector. A variety of slide trays are available with
capacity up to 140 slides. See your dealer in Kodak products for a
complete list of Kodak trays and accessories.
Place the tray over the center post of the projector. Align the “0” slot
with the gate index; the tray will drop into position.
If your slide tray does not drop easily, rotate the metal plate on the
bottom of the tray until it locks into position.
80 - Slide Tray
Metal plate
80 - Slide Tray
Operation
KODAK EKTALITE Slide Projectors 51
english
Place the loaded slide tray on the projector. Align the gate index at the
zero slide position. The tray will drop.
Front-Screen Projection
Remove the tray’s transparent cover (or the lock ring) by turning it
counterclockwise and lifting it off.
Check each slide’s orientation (horizontal or vertical) and arrange them
in the order you wish to show them. Then turn the slides upside down.
Number each mount in the upper right-hand corner.
Gate index
Lock ring
Operation
KODAK EKTALITE Slide Projectors
52
Insert your first slide into the first slot in the tray so that the number is
visible on the outer circumference of the tray.
A098_0050GC
Front Projection
A098_0051AC
Otros manuales para Ektalite 1000
1
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Proyector de Kodak
Kodak
Kodak FLIK X4 Manual de usuario
Kodak
Kodak FS-10-N Guía de solución de problemas
Kodak
Kodak Carousel S-AV 2010 Manual de usuario
Kodak
Kodak EKTALITE Manual de usuario
Kodak
Kodak V600 Manual de usuario
Kodak
Kodak EKTAPRO Manual de usuario
Kodak
Kodak EKTAPRO 7010 Manual de usuario
Kodak
Kodak Carousel S-AV 2050 Manual de funcionamiento
Kodak
Kodak DP800 - Digital Projector Instrucciones de funcionamiento
Kodak
Kodak DP850 - Ultra Digital Projector Guía de inicio rápido
Kodak
Kodak DP1050 ULTRA Manual de usuario
Kodak
Kodak Model AFT Manual de usuario
Kodak
Kodak Ektapro 4020 Manual de usuario
Kodak
Kodak DP2000 - Digital Projector Manual de usuario
Kodak
Kodak DP1100 - Digital Projector Manual de usuario
Kodak
Kodak Pocket Pico Projector Manual de usuario
Kodak
Kodak DP2000 - Digital Projector Manual de usuario
Kodak
Kodak Cube Manual de usuario
Kodak
Kodak Carousel S-AV1000 Manual de usuario
Kodak
Kodak DP2900 - Digital Projector Manual de usuario
