Kobalt SGY-AIR236 Manual de usuario

ATTACH YOUR RECEIPT HERE

Serial Number Purchase Date

Questions, problems, missing parts? Before returning to your

retailer, please call our Customer Service Department at

1-888-3KOBALT, 8 a.m. – 8 p.m., EST, Monday – Friday.

ITEM #0840780

MODEL #SGY-AIR236

1/2-IN 1000-FT-LB

IMPACT WRENCH

Français p. 16

Español p. 31

AB171057

Kobalt®is a registered trademark of LF, LLC.

TABLE OF CONTENTS

Safety Information..........................................................................................3

Compressor Requirements.............................................................................2

Package Contents..........................................................................................9

Product Specifications....................................................................................3

Preparation...................................................................................................10

Assembly Instructions...................................................................................10

Operating Instructions..................................................................................12

Care and Maintenance.................................................................................13

Troubleshooting............................................................................................14

Warranty.......................................................................................................15

COMPRESSOR REQUIREMENTS

IMPORTANT: To operate correctly, this tool requires airflow of at least 5

Standard Cubic Feet per Minute (SCFM) at 90 Pounds per Square Inch (PSI)

at the tool. The air hose length could affect how much air pressure the tool is

actually receiving. You may need to adjust the air pressure higher on the air

regulator to achieve the working pressure of 90 PSI.

SCFM 90

PSI

Tool Requirements

Exigences relatives aux outils

Requisitos de herramientas

PRODUCT SPECIFICATIONS SPECIFICATIONS

COMPONENT

SAFETY INFORMATION

Please read and understand this entire manual before attempting to

assemble, operate or maintain this product. If you have any questions,

please call our Customer Service Department at 1-

To reduce your exposure to chemicals, work in a well-ventilated area and

work with approved safety equipment, such as a respirator or dust masks

which are specially designed to filter microscopic particles.

888-3KOBALT,

8 a.m. – 8 p.m., EST, Monday – Friday.

WARNING

Improper operation or maintenance of this tool could result in serious injury

and property damage. Read and understand all warnings and operation

instructions before using this tool. When using any tool, basic safety

precautions should always be followed to reduce the risk of personal injury.

Use each tool for its intended function only. Do not use this product in

unsafe work conditions. It is always recommended to keep a fire

extinguisher and first aid kit near work areas.

FAILURE TO OBSERVE AND FOLLOW SAFETY INSTRUCTIONS COULD

RESULT IN INJURY OR DEATH.

1/2 IN.

7,000 RPM

1,000 FT.-LBS.

5 SCFM

1/4 IN. NPT

3/8 IN.

90 PSI

DRIVE

FREE SPEED

MAXIMUM TORQUE

AVERAGE AIR CONSUMPTION

AIR INLET

AIR HOSE

WORKING PRESSURE

SAFETY INFORMATION

RISK OF EYE OR HEAD INJURY

WARNING

WHAT COULD HAPPEN HOW TO PREVENT IT

This air powered tool is capable of

propelling materials such as

fasteners, metal chips, and other

debris at high speed which could

result in serious injury.

Always wear ANSI approved Z87.1

safety glasses.

Never leave operating tool

unattended.

Disconnect tool from air supply when

tool is not in use or when changing

accessories to prevent accidental

operation.

Compressed air can be hazardous,

propelling objects or particles that

can cause injury into soft tissues

such as eyes and ears.

For additional protection, use an

approved face shield in addition to

safety glasses.

Tool attachments can become loose

or break and fly apart, becoming

projectiles or propelling other objects

at the operator or bystanders in the

work area.

Make sure all attachments are

properly assembled and securely

fastened before use.

Always use the tool at a safe distance

from others in the work area.

Maintain awareness of work area

safety at all times.

RISK OF LOSS OF HEARING

RISK OF FIRE OR EXPLOSION

Always wear ANSI S3.19 hearing

protection.

Exposure to noise produced by air

tools can lead to permanent hearing

loss.

This tool is capable of generating

sparks, which can result in ignition of

flammable materials.

Never operate tools near flammable

substances such as gasoline,

naphtha, cleaning solvents, etc.

Work in a clean, well-ventilated area

free of combustible materials.

Never use oxygen, carbon dioxide or

other bottled gases as a power

source for air tools.

SAFETY INFORMATION

WARNING

WHAT COULD HAPPEN HOW TO PREVENT IT

RISK OF ENTANGLEMENT

RISK OF CUTS OR BURNS

Loose hair, clothing, jewelry or other

loose objects can become entangled

in the moving elements of this tool

and can cause serious injury.

Do not wear loose clothing, jewelry,

or anything that may get caught or

tangled when using tool.

Remove any jewelry which may be

caught by the tool.

Always keep hands and body parts

away from moving parts.

Always wear properly fitted clothing

and other properly fitted safety

equipment when using this tool.

This tool is capable of causing

serious injury if operated improperly,

or in a manner for which the tool is

not intended.

Keep the working part of the tool

away from hands and body.

Accessories can become extremely

hot through friction where they

contact the workpiece.

SAFETY INFORMATION

RISK OF ELECTRIC SHOCK

WARNING

WHAT COULD HAPPEN HOW TO PREVENT IT

RISK OF PERSONAL INJURY

This tool is not provided with an

insulated gripping surface. Contact

with a “live” wire will also make

exposed metal parts of the tool “live”

and can result in electrical shock,

electrocution or death.

Never use air tools where they may

come in contact with energized

electrical wiring.

Thoroughly investigate workpieces

and work areas for possible hidden

wiring before performing work.

Air tool accessories such as impact

sockets that come into contact with

hidden electrical wiring could cause

electrocution or death.

A tool left unattended or with the air

hose attached can be activated by

unauthorized persons leading to

their injury or injury to others.

Air tools can propel fasteners or

other materials throughout the work

area.

Air tools can become activated by

accident during maintenance or tool

changes.

Disconnect the tool from the air

supply during accessory changes,

tool changes, maintenance or repair.

Never carry the tool by the air hose.

To avoid unintentional operation,

never carry the tool with the trigger

depressed or engaged.

Only an authorized service

representative should service the

tool.

Remove air hose when the tool is

not in use and store tool in a secure

location away from reach of children

and untrained users.

Use only parts, fasteners and

accessories recommended by the

manufacturer.

Keep work area clean and free of

clutter.

Do not allow children to operate tool,

and keep children away from the

work area.

Keep work area well lit.

SAFETY INFORMATION

RISK OF PERSONAL INJURY

WARNING

WHAT COULD HAPPEN HOW TO PREVENT IT

Air tools can cause the workpiece to

move upon contact, leading to injury. Always make sure the workpiece is

secure. Use clamps or other devices

to prevent movement.

Before changing accessories,

making repairs, or when tool is not in

use, shut off the air supply and

release/drain air pressure from hose.

Disconnect tool from air supply and

store in a safe location.

Never use the tool while using drugs

or alcohol.

Loss of control of the tool can lead

to operator injury or injury to others

in the work area.

There is a risk of bursting if the tool

is damaged.

Poor quality, improper or damaged

attachments can detach or fly apart

during operation, sending projectiles

through the work area and causing

serious injury.

Follow lubrication instructions for

best and safest operation.

Follow instructions on how to

properly change accessories.

Always use tool attachments rated

for the speed of the power tool.

Never use tools, which have been

dropped, impacted, or are damaged.

Do not apply excessive force to the

tool; let the tool perform the work.

Never use a tool that is leaking air,

has missing or damaged parts, or

requires repairs.

Keep proper footing at all times when

handling tools. Slipping, tripping

and/or falling are major causes of

serious injury and or death.

Keep tool handles dry, clean and

free from oil/grease.

Stay alert. Use common sense.

Do not operate tools when you are

tired.

Always follow assembly, operation,

maintenance instructions.

SAFETY INFORMATION

RISK OF PERSONAL INJURY

WARNING

WHAT COULD HAPPEN HOW TO PREVENT IT

Improperly maintained tools and

accessories can cause serious injury.

Using an accessory not intended for

a specific tool increases the risk of

injury to the operator and everyone

else in the work area.

Repetitive motions, awkward

positions and exposure to vibration

can be harmful to hands and arms.

Discontinue use of tool if discomfort,

tingling feeling or pain occurs.

Consult a physician before resuming

use if any of these symptoms occur.

Always use accessories and

attachments designed for the tool

and the work at hand.

Do not improvise or modify tools or

accessories.

Maintain the tool and accessories

with care.

Keep tools clean and properly oiled

for best and safest performance.

PACKAGE CONTENTS

PREPARATION

DESCRIPTION QUANTITY

PART

1/2 in. Impact Wrench

Anvil

Trigger

Reverse Button

Forward Button

Air Inlet

E Torque Setting Switch

DR DF

Before assembling this tool, make sure all parts are present. Compare parts

with package contents list. If any part is missing or damaged, do not attempt

to assemble the tool.

Tools and Materials Required for Assembly (not included):

• 3/4 in. (19 mm) wrench

• 9/16 in. (14 mm) or adjustable wrench

• Thread sealant tape

• Tool oil

• Male plug

Estimated Assembly Time: 1 – 3 minutes

ASSEMBLY INSTRUCTIONS 1

1. Remove plastic air inlet protective cap

from air inlet (E) (See Figure 1).

NOTE: The air inlet (E) will spin freely, so

two wrenches are required to inert the

male plug.

2. Insert the male plug into the air inlet (E).

Using a 3/4 in. (19 mm)

wrench (not included) hold the air inlet

nut (E), and tighten the male plug by

turning it clockwise using a 9/16 in.

(14 mm) wrench (not included)

for an air tight connection (See Figure 2).

DO NOT OVERTIGHTEN.

33. Place 2 – 3 drops of air tool oil

(not included) into the opening of the

male air plug before each use

(See Figure 3).

NOTE: Use threaded sealant tape

(not included) on the threading of the

male plug.

Tabla de contenidos

Idiomas:

Otros manuales de Atornillador de impacto de Kobalt

Kobalt

Kobalt SGY-AIR185 Manual de usuario

Kobalt

Kobalt KIW 5024B-03 Manual de usuario

Kobalt

Kobalt SGY-AIR141 Manual de usuario

Kobalt

Kobalt KXIW 124B-03 Manual de usuario

Kobalt

Kobalt SGY-AIR166 Manual de usuario

Kobalt

Kobalt K20LW-26A Manual de usuario

Kobalt

Kobalt CID120KU Manual de usuario

Kobalt

Kobalt 6904 Manual de usuario

Kobalt

Kobalt 382461 Instrucciones de uso

Kobalt

Kobalt KID 124B-03 Manual de usuario

Kobalt

Kobalt KCW 5024B-03 Manual de usuario

Kobalt

Kobalt KID 124B-03 Manual de usuario

Kobalt

Kobalt KIW 124B-03 Manual de usuario

Kobalt

Kobalt KRAIW 124B-03 Manual de usuario

Kobalt

Kobalt SGY-AIR290 Manual de usuario

Kobalt

Kobalt 6904 Manual de usuario

Kobalt

Kobalt KXID 124B-03 Manual de usuario

Kobalt

Kobalt SGY-AIR216 Manual de usuario

Kobalt

Kobalt 6904 Manual de usuario

Kobalt

Kobalt SGY-AIR173 Manual de usuario

Kobalt

Kobalt SGY-AIR134 Manual de usuario

Kobalt

Kobalt KID 324B-03 Manual de usuario

Manuales populares de Atornillador de impacto de otras marcas

stayer

stayer IW500D Manual de usuario

Makita

Makita DTD152 Manual de usuario

Milwaukee

Milwaukee M12 FID Manual de usuario

Grizzly

Grizzly H6140 Manual de usuario

Makita

Makita BTW450 Manual de usuario

Ozito

Ozito LID-3000 Manual de usuario

Astro Pneumatic Tool

Astro Pneumatic Tool 1812 Manual de usuario

Greenlee

Greenlee HW3 Manual de usuario

Sthor

Sthor 57091 Manual de usuario

Makita

Makita DTD145 Manual de usuario

Hilti

Hilti SIW 2-A12 Manual de usuario

Ryobi

Ryobi R18IW3 Manual de usuario

Parkside

Parkside PDSSA 20-Li A1 Manual de usuario

Flex

Flex FX1471 Manual de usuario

SATA

SATA 51075C Manual técnico

Cembre

Cembre NR-11P Manual de usuario

Makita

Makita BTP131RFE Manual de usuario

DeWalt

DeWalt XR Li-ion DCF902 Manual de usuario