Knightsbridge UCLCT4 Manual de instrucciones

INSTALLATION & MAINTENANCE MANUAL

UCLCT4 / UCLCT9 / UCLCT13 / UCLCT18

These instructions should be read carefully and retained after installation by the

end user for future reference and maintenance.

These instructions should be used to aid installation of the following products:

UCLCT4 / UCLCT9 / UCLCT13 / UCLCT18

GENERAL INSTRUCTIONS

SAFETY

• This product must be installed in accordance with the latest edition of the IEE Wiring

Regulations (BS7671) and current Building Regulations. If in any doubt, consult a qualiﬁed

electrician

• Please isolate mains prior to installation or maintenance

• Check the total load on the circuit (including when this luminaire is ﬁtted) does not exceed

the rating of the circuit cable, fuse or circuit breaker

• Please note the IP (Ingress Protection) rating of this luminaire when deciding the location

for installation

•This product is for indoor use only

• This product is Class II double insulated

•This product is IP20 rated

INSTALLATION

Note - If this luminaire is being used in conjunction with an external PIR or sensor, please

conﬁrm with the manufacturer of the sensors that they are compatible with LED luminaires.

• Provide a suitable power supply to the required position of the luminaire and connect to

the supplied power cable ensuring correct polarity is observed

• Mark the location of the ﬁxing holes for the mounting clips. The mounting clips should be

spaced so as to distribute the weight of the luminaire evenly. Drill the holes ensuring not

to infringe with any gas / water pipes or electrical cables (see Fig. 1)

INSTRUCTIONS –UCLCTx

These instructions should be read carefully and retained after installation by the end user for future reference and

maintenance.

These instructions should be used to aid installation of the following products:

UCLCT4 / UCLCT9 / UCLCT13 / UCLCT18

SAFETY

•This product must be installed in accordance with the latest edition of the IEE Wiring Regulations

(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician

•Please isolate mains prior to installation or maintenance

•Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating

of the circuit cable, fuse or circuit breaker

•Please note the IP (Ingress Protection) rating of this luminaire when deciding the location for

installation

•This product is Class II double insulated

•This series is IP20 rated

INSTALLATION

Note - If this luminaire is being used in conjunction with an external PIR or sensor, please confirm with

the manufacturer of the sensors that they are compatible with LED luminaires.

•Provide a suitable power supply to the required position of the luminaire and connect to the

supplied power cable ensuring correct polarity is observed

•Mark the location of the fixing holes for the mounting clips. The mounting clips should be spaced so

as to distribute the weight of the luminaire evenly. Drill the holes ensuring not to infringe with any

gas / water pipes or electrical cables (see Fig. 1)

Fig. 1

•Push the luminaire into the mounting clips to secure into place

•Connect the power lead to the end of the luminaire, switch on the power supply and check for

correct operation

•Multiple fittings can be connected together by using the coupler or link leads (not included)

CHANGING THE COLOUR TEMPERATURE

The colour temperature of an individual fitting can be changed by means of the switch located on the fitting.

The colour temperature of a group of fittings can be changed by means of a wall switch.

•To change colour temperature, switch off and on again within one second. The colour will change each

time this is done

Fig.1

•Connect the power cord to the mains supply ensuring the correct polarity is observed:

L -Live (brown), N - Neutral (blue), and plug into the luminaire

•Multiple ﬁttings can be linked together using a coupler (included) or link leads (available

separately) up to a maximum of 20 ﬁttings

•Switch on and check for correct operation

The colour temperature of an individual ﬁtting can be changed by means of the switch

located on the ﬁtting.

The colour temperature of a group of ﬁttings can be changed by means of a wall switch.

• To change colour temperature, switch off and on again within one second. The colour will

change each time this is done

• To retain colour temperature, switch off for longer than three seconds before switching on

again. The colour temperature will be retained

• If any of the luminaires are switched off and on again for an interval between one and

three seconds, they may go out of synchronisation with each other. If this happens the

switches located on the individual ﬁttings must be used to resynchronise them

• The switch on each individual ﬁtting will only affect the colour temperature of that ﬁtting,

not of those connected after it

CHANGING THE COLOUR TEMPERATURE

GENERAL

WARNING

This product contains a light source of energy efﬁciency class F to Regulation (EU)

No. 2019/2015.

This product contains a non-replaceable LED light source and control gear.

Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which

may damage the product.

This product is non-dimmable.

This product should be dismantled for disposal when it reaches the end of its life. Please

see website for dismantling instructions.

This product should be recycled in the correct manner when it reaches the end of its life.

Check local authorities for where facilities exist.

This luminaire must be disconnected from the circuit if subjected to any high voltage or

insulation resistance testing. Irreparable damage will occur if this instruction is not followed.

Non-replacable light source

Non-replacable gear tray

DCJUL21_V2

WARRANTY

This product has a warranty of 2 years from date of purchase. Failure to install this product

in accordance with the current edition of the IEE Wiring Regulations (BS7671), improper

use, or removal of the batch codes will invalidate the warranty. If this product should fail

within its warranty period, it should be returned to the place of purchase for a free of

charge replacement. ML Accessories does not accept responsibility for any installation costs

associated with the replacement product. Your statutory rights are not affected.

ML Accessories reserve the right to alter product speciﬁcation without prior notice.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de iluminación de Knightsbridge

Knightsbridge

Knightsbridge LEDFIPRGBW Manual de instrucciones

Knightsbridge

Knightsbridge TNXQUADMWW Manual de instrucciones

Knightsbridge

Knightsbridge RWL Series Manual de instrucciones

Knightsbridge

Knightsbridge BT9EMS Manual de instrucciones

Knightsbridge

Knightsbridge TNXQUADSTW Manual de instrucciones

Knightsbridge

Knightsbridge TNXQUADMWSTW Manual de instrucciones

Knightsbridge

Knightsbridge KIT4B Manual de instrucciones

Knightsbridge

Knightsbridge BATC Series Manual de instrucciones

Knightsbridge

Knightsbridge 12DC36 Manual de instrucciones

Knightsbridge

Knightsbridge LFX512WW Manual de instrucciones

Knightsbridge

Knightsbridge CPL6CT Manual de instrucciones

Knightsbridge

Knightsbridge RCTRGB Manual de instrucciones

Knightsbridge

Knightsbridge WW15C Manual de instrucciones

Knightsbridge

Knightsbridge OS002 Manual de instrucciones

Knightsbridge

Knightsbridge BF1430EMS Manual de instrucciones

Knightsbridge

Knightsbridge EMGUKIT1 Manual de instrucciones

Knightsbridge

Knightsbridge EMXST Manual de instrucciones

Knightsbridge

Knightsbridge EMPOWERST Manual de instrucciones

Knightsbridge

Knightsbridge LED Series Manual de instrucciones

Knightsbridge

Knightsbridge SLIGHT2 Manual de instrucciones

Knightsbridge

Knightsbridge SLULED Manual de instrucciones

Knightsbridge

Knightsbridge VFR7EM Manual de instrucciones

Knightsbridge

Knightsbridge TRLED EM Series Manual de instrucciones

Knightsbridge

Knightsbridge GDL2 Manual de instrucciones

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario